Section 4 − Specifications; Serial Number And Rating Label Location; Software Licensing Agreement; Information About Default Weld Parameters And Settings - Hobart Multi-Handler 200 Owner's Manual

4-1. Serial Number And Rating Label Location

The serial number and rating information for this product is located on the back of unit. Use rating label to determine input power requirements and/or
rated output. For future reference, write serial number in space provided on back cover of this manual.

4-2. Software Licensing Agreement

The End User License Agreement and any third-party notices and terms and conditions pertaining to third-party software can be found at
https://www.hobartwelders.com/eula

4-3. Information About Default Weld Parameters And Settings

NOTICE − Each welding application is unique. Although certain Miller Electric products are designed to determine and default to certain typical welding
parameters and settings based upon specific and relatively limited application variables input by the end user, such default settings are for reference
purposes only; and final weld results can be affected by other variables and application-specific circumstances. The appropriateness of all parameters
and settings should be evaluated and modified by the end user as necessary based upon application-specific requirements. The end user is solely
responsible for selection and coordination of appropriate equipment, adoption or adjustment of default weld parameters and settings, and ultimate
quality and durability of all resultant welds. Miller Electric expressly disclaims any and all implied warranties including any implied warranty of fitness
for a particular purpose.

4-4. Unit Specifications For MIG (GMAW)

.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input Rated Welding
Voltage Output
100 A @ 19.0 Volts DC
40% Duty Cycle
120 VAC
Wire Type
And Diameter
200 A @ 24.0 Volts DC
15% Duty Cycle
140 A @ 21.0 Volts DC
40% Duty Cycle
240 VAC
Wire Type
And Diameter

4-5. Unit Specifications For TIG (GTAW)

.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input Rated Welding
Voltage Output
140 A @ 15.6 Volts AC/DC
120 VAC
20% Duty Cycle
200 A @ 18.0 Volts AC/DC
240 VAC
20% Duty Cycle

4-6. Unit Specifications For Stick (SMAW)

.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input Rated Welding
Voltage Output
80 A @ 23.2 Volts AC/DC
120 VAC
40% Duty Cycle
170 A @ 28.0 Volts AC/DC
240 VAC
15% Duty Cycle
.
A complete Parts List is available at www.HobartWelders.com
SECTION 4 − SPECIFICATIONS
.
and are incorporated by reference herein.
Amperage
Range
30 − 120
Solid/Stainless
.024 - .035 in.
(0.6 - 0.8 mm)
30 − 200
Solid/Stainless
.024 − .035 in.
(0.6 − 0.9 mm)
Amperage
Range
20 − 140
20 − 200
Amperage
Range
30 − 100
30 − 200
Maximum Open-
Circuit Voltage
DC
63
Flux Cored
.030 - .035 in.
60 − 650 IPM (1.5 − 16.5 m/min)
(0.8 - 0.9 mm)
63
Flux Cored
.030 − .045 in.
60 − 650 IPM (1.5 − 16.5 m/min)
(0.8 − 1.2 mm)
Maximum Open-
Circuit Voltage
DC
63
63
Maximum Open-
Circuit Voltage
DC
63
63
Amperes Input at Rated
Load Output, 50/60 Hz,
Single-Phase
20.9
Wire Feed Speed Range
25.0
25.1
Wire Feed Speed Range
Amperes Input at Rated
DC Load Output,
50/60 Hz, Single-Phase
25.0
20.0
Amperes Input at Rated
DC Load Output,
50/60 Hz, Single-Phase
19.2
23.5
OM-285922 Page 11