Advertisement
Quick Links
Advertisement
Related Manuals for AEG BEWS18125BLC
Summary of Contents for AEG BEWS18125BLC
- Page 1 BEWS18125BLC BEWS18125BLP Original instructions...
- Page 2 Important! This appliance is not intended to be used or cleaned by persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given instructions concerning the safe use of the appliance by a person legally responsible for their safety. They should be supervised whilst using the appliance.
- Page 3 12. Dust cover 3. Spindle lock button 8. Half tool-less wheel guard 13. Battery port 4. Grinding wheel 9. Anti-vibration auxiliary handle 14. Toolless cutting guard 5. Standard outer flange nut 10. Auxiliary handle 15. Wrench BEWS18125BLC BEWS18125BLP BEWS18125BLP BEWS18125BLC BEWS18125BLP BEWS18125BLC...
- Page 4 BEWS18125BLC BEWS18125BLP...
- Page 5 BEWS18125BLP BEWS18125BLC START START STOP STOP BEWS18125BLC BEWS18125BLP...
- Page 6 BEWS18125BLC...
- Page 7 BEWS18125BLP...
- Page 9 click click...
- Page 10 0° 30° 30° 60° 60°...
- Page 11 BEWS18125BLC WARNING: Always check the spindle lock button is fully released before switching on the tool! After using the spindle lock to tighten / loosen the abrasive disk, it is possible that the button may stick in the lock position. Whilst this will not damage the tool it may cause the tool or battery protection to operate and remove power to the tool.
- Page 12 BEWS18125BLC...
- Page 13 BEWS18125BLP WARNING: Always check the spindle lock button is fully released before switching on the tool! After using the spindle lock to tighten / loosen the abrasive disk, it is possible that the button may stick in the lock position. Whilst this will not damage the tool it may cause the tool or battery protection to operate and remove power to the tool.
- Page 14 BEWS18125BLP...
- Page 15 Remove the battery pack before starting any work on the product.
- Page 16 78-100 % 55-77 % 33-54 % 10-32 % <10 %...
- Page 17 BEWS18125BLC Start Stop...
- Page 18 BEWS18125BLC Start Start Steady Red Stop Start...
- Page 19 BEWS18125BLC Flashing Red (Overload) Electronic brake Start...
- Page 20 BEWS18125BLP Start Stop...
- Page 21 BEWS18125BLP Start Start Steady Red Stop Start...
- Page 22 BEWS18125BLP Flashing Red (Overload) Electronic brake Start...
- Page 23 < 30°...
- Page 24 Accessory...
- Page 25 Accessory...
- Page 26 Accessory...
- Page 27 Remove and brush the dust cover after every 5 hours of work. (Sooner in dusty environments) If over current protection is frequent, check if there is any blockage at the vents. Clean as necessary and try again. click...
-
Page 28: Angle Grinder Safety Warnings
L1890R b. Operations such as sanding or polishing are not recommended to be performed with this power tool. Use AEG 18V battery and charger only Operations for which the power tool was not designed may... - Page 29 create a hazard and cause personal injury. Sparks could ignite these materials. c. Do not use accessories which are not specifically designed o. Do not use accessories that require liquid coolants. Using and recommended by the tool manufacturer. Just because water or other liquid coolants may result in electrocution or the accessory can be attached to your power tool, it does not shock.
-
Page 30: Additional Safety Warnings
Do not dispose of used battery packs in the household refuse or wheel. When the wheel, at the point of operation, is moving by burning them. AEG Distributors offer to retrieve old batteries to away from your body, the possible kickback may propel the protect our environment. -
Page 31: Maintenance
Battery packs which have not been used for some time should be need to be replaced which have not been described, please contact recharged before use. one of our AEG service agents (see our list of guarantee/service Temperatures in excess of 50°C (122°F) reduce the performance of addresses). - Page 32 SYMBOLS Safety alert Rated speed Volts Direct current Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements. Please read the instructions carefully before starting the machine. Always wear goggles when using the machine. Always wear gloves when using the machine. Remove the battery pack before starting any work on the machine.
- Page 36 www.aegpowertools.com.au www.aegpowertools.co.nz Techtronic Industries Australia Pty Ltd 31 Gilby Road, Mount Waverley, VIC 3149 Melbourne, Australia Techtronic Industries N.Z. Limited 2 Landing Drive, Mangere Auckland, 2022, New Zealand 961096412-01A...