Advertisement
grinding wheel flanges.
e. Do not use worn down wheels from larger power tools. Wheel
intended for larger power tool is not suitable for the higher
speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-Off
Operations:
a. Do not "jam" the cut-off wheel or apply excessive pressure. Do
not attempt to make an excessive depth of cut. Overstressing
the wheel increases the loading and susceptibility to twisting or
binding of the wheel in the cut and the possibility of kickback
or wheel breakage.
b. Do not position your body in line with and behind the rotating
wheel. When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel the
spinning wheel and the power tool directly at you.
c. When wheel is binding or when interrupting a cut for any
reason, switch off the power tool and hold the power tool
motionless until the wheel comes to a complete stop. Never
attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate
and take corrective action to eliminate the cause of wheel
binding.
d. Do not restart the cutting operation in the workpiece. Let
the wheel reach full speed and carefully re-enter the cut.
The wheel may bind, walk up or kickback if the power tool is
restarted in the workpiece.
e. Support panels or any oversized workpiece to minimize the
risk of wheel pinching and kickback. Large workpieces tend
to sag under their own weight. Supports must be placed under
the workpiece near the line of cut and near the edge of the
workpiece on both sides of the wheel.
Use extra caution when making a "pocket cut" into existing
f.
walls or other blind areas. The protruding wheel may cut gas or
water pipes, electrical wiring or objects that can cause kickback.
Safety Warnings Specific for Wire Brushing Operations:
a. Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing, do
not allow any interference of the wire wheel or brush with the
guard. Wire wheel or brush may expand in diameter due to work
load and centrifugal forces.
ADDITIONAL SAFETY WARNINGS
Dust and splinters must not be removed while the machine is running.
Never reach into the danger area of the tool when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and separating.
Immediately switch off the machine in case of considerable vibrations
or if other malfunctions occur. Check the machine in order to find out
the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, flying sparks are produced. Take care that no
persons are endangered. Because of the danger of fire, no combustible
materials should be located in the vicinity (spark flight zone). Do not
use dust extraction.
30
Due care should be taken that no sparks or sanding dust flying from
the workpiece come into contact with you.
The adjusting nut must be tightened before starting to work with the
machine.
The workpiece must be fixed if it is not heavy enough to be steady.
Never lead the workpiece to the grinding disk with your hand.
For accessories intended to be fitted with threaded hole wheel, ensure
that the thread in the wheel is long enough to accept the spindle
length.
For cutting or separating use a closed protection cap, available as an
accessory.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System GBS chargers for charging System GBS battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING! To reduce the risk of fire, personal injury, and product
damage due to a short circuit, never immerse your tool, battery pack
or charger in fluid or allow a fluid to flow inside them. Corrosive or
conductive fluids, such as seawater, certain industrial chemicals, and
bleach or bleach containing products, etc., can cause a short circuit.
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise and the operator should pay special attention to
avoid the following:
■ Injury caused by thrown-off particles
– Metal or abrasive particles may enter the eyes and cause
severe permanent damage. Wear goggles approved for
grinding operations whenever you use the product.
■ Injury caused by vibration
– Limit exposure. See Risk Reduction.
■ Injury caused by dust
– Wear appropriate dust control mask with filters suitable for
protecting against particles from the material being worked
on and abrasive particles from the grinding disc. Do not eat,
drink, or smoke in the work area. Ensure adequate ventilation.
■ Injury from contact with the grinding disc
– The disc and workpiece will become hot during use. Wear
gloves when changing discs or touching workpiece. Keep
hands away from the grinding area at all times. Clamp the
workpiece whenever possible.
■ Injury caused by noise
– Prolonged exposure to noise will increase the risk of hearing
damage, and the effects are cumulative. When using power
30
Advertisement
