Page 2
As a result, people all over the world are benefiting from the TRUE experience. Innovation across the full product line has made TRUE successful and is a trademark of the TRUE heritage. TRUE’s patented Heart...
ABLE ONTENTS ........................4 AFETY ................ENERAL ARE AND AINTENANCE ................... 8 IMENSIONS AND EIGHT ......................9 REPARATION .................... 10 ARTON ONTENTS .................... 11 ARTON ONTENTS & A NSTALLATION SSEMBLY 1: A ..............12 SSEMBLE THE RAME 2: A & L ............
9. If the machine appears damaged or inoperable, contact a facility staff member to place an “OUT OF ORDER, DO NOT USE” sign on the machine until it is repaired. Only use TRUE supplied replacement components to service this machine.
Page 5
3. Install this piece of equipment on a solid level surface that does not deviate more then 1/8” over a 10’ distance (or as defined and required by local building and architectural codes. 4. TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability.
Page 6
• Frames and Lifting Arms: Inspect weekly for integrity and function. Replace any component at first signs of wear. Use only TRUE supplied components. 4. Replace any warning label at first sign of wear. Labels and the Facility Safety Sign may be obtained from TRUE free of charge.
Be sure all hardware is tight before using the machine. Retain these instructions for future reference. If you have any questions, do not hesitate to contact your TRUE dealer or TRUE at (800) 883-8783 or service@truefitness.com.
REPARATION EQUIRED OOLS Ratchet Wrench and Socket: 9/16” Wrenches: 9/16” (or an adjustable crescent wrench). Rubber mallet. Allen wrenches: (included with the machine) Weight Plate Cartons Depending upon your order, this machine can be assembled with either a 170 lb. or 250 lb.
ARTON ONTENTS ITEM UMBER ESCRIPTION FS-CAP-000X TOP CAP FS53-SHD-300X FRONT SHROUD FS-SHD-350X REAR SHROUD FS53-UPR-000X UPRIGHT FS53-GRD-300X GUIDE ROD FS53-PAD-100X SEAT PAD FS-BKT-000 GUIDE ROD BRACKET FS-PAD-400X ROLLER PAD, SHORT FS-BKT-001 TOP CAP BRACKET FS-WSB-000 WEIGHT STACK BASE...
1: A SSEMBLE THE RAME 1. Assemble frame components as shown. ITEM UMBER ESCRIPTION FS53-UPR-000X UPRIGHT FRAME 2. Loosely assemble ALL hardware shown in this step. FS53-SFR-300X SEAT FRAME 3. After aligning all component edges and FS53-SFR-400X THIGH FRME surfaces, tighten the hardware. FS53-PAD-100X SEAT PAD 4.
Page 13
1: A SSEMBLE THE RAME 10,14,12,9,11 X 3 DETAIL A 10,15,9,12,11 X 2 DETAIL B...
2: A & L SSEMBLE EIGHT TACK AT TUBE 1. Assemble the Weight Stack, ITEM UMBER ESCRIPTION Bumper, Weight Stack Support, FS-GRD-300X GUIDE ROD Top Plate/Selector Bar, Guide FS-SBR-000X TOP PLATE/SELECTOR BAR Rods, Weight Stack 1” Washer, and Collars as shown below. C 757A WASHER, WEIGHT STACK 1”...
2: A & L SSEMBLE EIGHT TACK AT TUBE 10,8,9 X 4 DETAIL D Set the distance between the Collars and the tube as shown Use tape measure 1” distance from the bottom of the bolt to the top of the bar as shown. Lock the nut after the distance is set.
SSEMBLE RONT HROUD RAME ITEM UMBER ESCRIPTION 1. Install the front Shroud first. Slide the top portion of the shroud up to FS53-SHD-300X FRONT SHROUD the Lat Tube from the side, and FS53-MFR-200X ROW TUBE push the lower portion of the FS53-SFR-100X FOOT FRAME shroud into the Upright.
Page 17
ONTINUED 7,5,9,6 X 2 6,12,5,7 X 2 DETAIL F 7,5,9,6 X 2 6,13,8,5,7 X 2 DETAIL G...
Page 18
ONTINUED 7,5,9,6 X 2 6,13,8,5,7 X 2 DETAIL H Slide Foot Plate on to the Foot Frame and tighten all hardware. 6,11,8,5 X 4...
& R SSEMBLE ABLE UPPORT 1. Install the Row Tube Support ITEM UMBER ESCRIPTION below, then tighten all hardware in FS53-MFR-300X ROW TUBE SUPPORT previous steps. FS53-ROL-001A ROW TUBE A, PVC FS53-ROL-002A ROLL SHAFT A 2. Install the Row Cable as shown B 900 PULLEY, 4.5”...
Page 20
& R SSEMBLE ABLE UPPORT 9,13,8,7 Adjust stop to remove cable slack. 9,16,8,7 DETAIL M 9,12,8,6 X 2 9,16,8,7,5 9,16,8,7 2 X 2 9,14,8,7,5 9,15,8,7 3 X 2 9,12,8,6 X 2 DETAIL N...
5: I & R NSTALL ANDLE 1. Install the Lat Bar and Row Handle ITEM UMBER ESCRIPTION as shown below. FS-BAR-100X LAT BAR FS-BAR-200X ROW HANDLE B 1004 1/4 QUICK LINK...
6: I & T NSTALL HROUD 1. Install the Rear Shroud, put the ITEM UMBER ESCRIPTION bottom of the shroud in first and push FS-SHD-350X REAR SHROUD the shroud into the upright. FS-CAP-000X TOP CAP 2. Install the Top Cap on the upright as C 754C WASHER, FLAT 3/8 shown in view DETAIL AF.
7: I NSTALL THE EIGHT TACK ABEL 1. Select the appropriate weight stack label(s) according to your order. You can install pound labels, kilogram labels, or both. 2. If you ordered a 170 lb weight stack, use labels: LBL-WSE-01170 (for pounds) LBL-WSM-01170 (for kilograms).
(European) safety standards for stability (without floor anchors) when the machine is used for it’s intended purpose as designated by the manufacturer. However, TRUE strongly recommends that all equipment be anchored to the floor to prevent movement and increase stability.
Cables should be replaced at the first sign of wear or on an annual basis. Both cables on this machine should be replaced at the same time. Use only genuine TRUE cables. Please refer to the following diagram when replacing the cable to insure that it is properly routed.
Page 27
& C ABLE EPLACEMENT ABLE OUTING IAGRAM CABLE RETAINER PINS CORRECT CABLE MUST BE ROUTED ABOVE THE VERTICAL FRAME BOLTS WRONG! WRONG! CABLE RETAINER BOLT WRONG!
ACHINE ABELS The following are the warning labels required for this FS machine. If any of these labels are missing or become damaged, TRUE will replace them free of charge. Note: these labels are not to scale. scale. B2051 B2141C...
O W T O B T A I N E R V I C E For warranty service, contact an Authorized TRUE Dealer or a TRUE Customer Service representative at 1-800-883-8783. You can also email us at nasales@paramountfitness.com. Before you call, please have the following information ready: •...
Page 30
Hours of operation 8:30am - 5:00 pm CST workmanship for a 10 years. The frame is warranted for labor and freight (for parts shipped from TRUE) for one year from date of purchase. * This limited warranty on structural frame does not include paint or coatings.
Page 31
(if anyone other than a TRUE authorized dealer/ technician initially assembles and installs the Product, this The FS-53 comes with one serial number on the base of the Limited Warranty will be void unless the written authorization machine. Please write down your serial number below and keep of TRUE is first obtained).
Page 32
If you prefer to mail your warranty card, have the owner of the product complete the information below and return it to TRUE Fitness within 30 days from the date of equipment installation.