Page 3
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from PoE(53 Vdc), 0.32 A. (PNM-8082VT) EXPLANATION OF GRAPHICAL SYMBOLS 16. This product is intended to be supplied by isolation power.
Page 4
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a ~ Do not place this apparatus on an uneven surface. protective earthing connection. ~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area.
CONTENTS OVERVIEW Important Safety Instructions WEB VIEWER Connecting to the Camera Recommended PC Specifications Password setting Recommended Micro SD/SDHC/SDXC Login Memory Card Specifications Camera Web Viewer Setup What’s Included Optional Accessories for Installation At a Glance APPENDIX Troubleshooting INSTALLATION & CONNECTION Installation Powering and networking NETWORK CONNECTION AND...
overview RECOMMENDED PC SPECIFICATIONS WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. ~ CPU : Intel(R) Core(TM) i7 3.4 GHz or higher (As for each sales country, accessories are not the same.) ~ RAM : 8G or higher ~ Recommended browser: Chrome Appearance...
OPTIONAL ACCESSORIES FOR INSTALLATION AT A GLANCE You can purchase appropriate optional accessories available. Appearance Product type Wall mount Model Name SBP-300WMW1 Product type Hanging mount Ceiling mount Model Name SBP-276HMW SBP-300CMW Product type Corner mount Pole mount Model Name SBP-300KMW SBP-300PMW Item...
Page 8
overview Components Item Description Output port for test monitoring the video output. Use the test monitor cable to connect to a Test monitor out port mobile display and check the test video. The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.
installation & connection INSTALLATION 2. Loosen the fastening screw on the camera body. You don’t have to completely remove the screws. This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Page 10
installation & connection Inserting a Micro SD card Removing a Micro SD card Gently press down on the exposed end of the Micro SD card as shown in the diagram to eject the Micro SD 1. Remove the dome cover of the camera. card from the slot.
Page 11
Installation (mount plate) 1-3. Pull out network cable through the hole in the mount plate. [Directly installing on ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2.
Page 12
installation & connection 2-3. Place the pipe on the mount plate. [Attaching to the unbundled adapter] 2-4. Fix the mount plate using appropriate screws. Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.
Page 13
Installation (camera body and dome cover) 3. Connect the network cable jack to the PoE+ port of the camera. Refer to “Connecting waterproof network cable” on page 14. 1. Connect the safety wire. 4. Push the mounting clip until it clicks into place as shown in the figure. 2.
Page 14
installation & connection 6. Adjust the lens to the desired direction by referring to “Adjusting the monitoring direction for the Connecting waterproof network cable camera”. (Page 16) Use an appropriate cable bush for the network cable to be connected. If you tilt the lens, you may need to adjust the lens as this may block the screen. - Basic camera : Use the cable with a diameter of Ø5~6.5.
Page 15
4. Connect the network cable jack to the PoE+ port of the camera. Connecting the installation monitor Connect the test monitor out port of this product to the video input terminal of the monitor for installation. The wiring varies depending on your monitor type and peripheral devices; please refer to the user manual for each device. Please make sure the monitor and camera are turned off when connecting them.
Page 16
installation & connection How to set up channels to monitor for installation Adjusting the monitoring direction for the camera The camera body has a channel DIP switch, as shown in the figure. You can change the channel of the camera using the channel DIP switches. Tilt Moving the camera module (Pan) Lens Rotation...
POWERING AND NETWORKING Connect the PoE+ device with the PoE+ port of the camera. Connect and use a PoE+ -enabled router. Use a PoE+ device that complies with the IEEE 802.3at standard. If you connect using an PoE+ -enabled router, you don't need a separate power supply cable to power it on. Network Cable Specification Item Contents...
network connection and setup network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING Connecting to the camera from a local PC in the LAN INTERNET 1.
USING DEVICE MANAGER If using a Broadband Router ~ IP Address : Enter an address falling in the IP range provided by the Broadband Router. Device manager program can be downloaded from <Technical Guides>-<Online Tool> menu at Hanwha Techwin website ex) 192.168.1.2~254, 192.168.0.2~254, (http://www.hanwha-security.com).
~ Example of the Dynamic IP environment configure the IP. PNM-8082VT - If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 2. Click < + > at the main page of device manager.
Port forwarding can be done without additional router setup if the router supports the UPnP (Universal Plug and Play) function. For more information, refer to the user manual of the applicable router. After connecting the network camera, select the checkbox from the menu <Quick connect> in <Wisenet DDNS> in “Settings -> Network -> DDNS”.
2. From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the IP address of the Broadband Router in the address bar. ex) http://ddns.hanwha-security.com/ID To use Wisenet DDNS, sign up at the Wisenet DDNS homepage (http://ddns.hanwha-security.com) and register the product at [My DDNS]>[Register Product]. 22_ network connection and setup...
To register your device to the <DDNS> server, visit http://ddns.hanwha-security.com and register your device first, and then set the Web Viewer’s <Network> - <DDNS> to <Wisenet DDNS>, as well as providing Type the IP address and HTTP port number of the camera in the address bar.
web viewer PASSWORD SETTING CAMERA WEB VIEWER SETUP When you access the product for the first time, you must register the 1. Click the [Setup ( )] icon. login password. 2. The Settings window appears. 3. You can configure settings for the camera’s basic information, video, audio, network, event, analysis, and For a new password with 8 to 9 digits, you must use at least 3 of system over the network.
appendix TROUBLESHOOTING PROBLEM SOLUTION ~ Check whether two or more cameras are set to a single multicast address instead of different PROBLEM SOLUTION Images overlap. addresses. If a single address is used for multiple cameras, the images may overlap. ~ On the authentication popup window prompted when initially accessing https, click "View ~ If the transmission method is set to multicast, check whether there is a router that supports Authentication Certificate"...
Page 26
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the PNM-8082VT and is the answer not in the manual?
Questions and answers