Advertisement
Quick Links
Advertisement
Related Manuals for Sherman digitec DIGITIG PULSE AC/DC 200GD
Summary of Contents for Sherman digitec DIGITIG PULSE AC/DC 200GD
- Page 1 V1.2 17/08/07 USER MANUAL WELDING RECTIFIER Inverter DIGITIG PULSE AC / DC 200GD...
- Page 2 EDGE WITH EQUIPMENT! EDGE WITH EQUIPMENT! EDGE WITH EQUIPMENT! before installation and and start-up device and equipment should with y acquainted Æ si ę with this and instructions and before installation and and start-up device and equipment should with y acquainted Æ si ę with this and instructions and before installation and and start-up device and equipment should with y acquainted Æ...
- Page 3 Poisoning prevention vapors and gases secreted during the welding electrodes and coatings Evaporation metals: • use Æ device and the ventilation device being cut and and g and installed in limited air exchange, use Æ device and the ventilation device being cut and and g and installed in limited air exchange, use Æ...
-
Page 4: Specifications
3. GENERAL DESCRIPTION DIGITIG PULSE AC / DC converter serving 200GD with s welding r ę handwriting pr and dem constant and alternating structural steel coated DIGITIG PULSE AC / DC converter serving 200GD with s welding r ę handwriting pr and dem constant and alternating structural steel coated DIGITIG PULSE AC / DC converter serving 200GD with s welding r ę... - Page 5 Degree ñ protection Degree ñ protection Degree ñ protection IP set ś la the extent to which devices and The unit is resistant to a passage ę to internal and inside pollution ñ IP set ś la the extent to which devices and The unit is resistant to a passage ę to internal and inside pollution ñ IP set ś...
- Page 6 7.2 TIG terminal pr and dowy should handle with s connected and whether Æ slot of negative polarization (6), plug control and cy carefully handle Screw ę these Æ the terminal pr and dowy should handle with s connected and whether Æ slot of negative polarization (6), plug control and cy carefully handle Screw ę these Æ the terminal pr and dowy should handle with s connected and whether Æ...
- Page 7 8. FUNCTIONAL DESCRIPTION switches and POKR Ê Tel 8. FUNCTIONAL DESCRIPTION switches and POKR Ê Tel 8. FUNCTIONAL DESCRIPTION switches and POKR Ê Tel 8.1 Front and rear panel 1. Off and main switch 1. Off and main switch 1. Off and main switch 2.
- Page 8 B - Setting the welding parameters, memory Ec Act ñ Ec Act ñ Ec Act ñ Adjust welding parameters Regulation of welding parameters make up ę for help and buttons Regulation of welding parameters make up ę for help and buttons Regulation of welding parameters make up ę...
- Page 9 D - button On and on / off and switching pulse D - button On and on / off and switching pulse D - button On and on / off and switching pulse D - button On and on / off and switching pulse D - button On and on / off and switching pulse Off button active and including welding methods and TIG.
- Page 10 for you ś display appears ę inscription "LL". "Err" indicates overheating or the incorrect ś CIW and wash ę for you ś display appears ę inscription "LL". "Err" indicates overheating or the incorrect ś CIW and wash ę for you ś display appears ę inscription "LL". "Err" indicates overheating or the incorrect ś CIW and wash ę for you ś...
- Page 11 pr and d crater - pr and d used in some modes of welding, when the arc is not extinguished immediately after the descent phase pr and the welding. pr and d crater - pr and d used in some modes of welding, when the arc is not extinguished immediately after the descent phase pr and the welding. pr and d crater - pr and d used in some modes of welding, when the arc is not extinguished immediately after the descent phase pr and the welding.
- Page 12 to zajarzy Æ arc mode should dwutaktu with s approaching with s Æ electrode ę to the workpiece on the distance SC 2 mm and press rte d button in the to zajarzy Æ arc mode should dwutaktu with s approaching with s Æ electrode ę to the workpiece on the distance SC 2 mm and press rte d button in the to zajarzy Æ...
-
Page 13: Before Calling Service
t4 : t4 : push rte d the handle. pr and welding current starts falling Æ the worth ś you pr and large crater. them ś l On and pulsator is connected, push rte d the handle. pr and welding current starts falling Æ the worth ś you pr and large crater. them ś l On and pulsator is connected, push rte d the handle. -
Page 14: Maintenance Instructions
12. OPERATION MANUAL Operation of devices and DIGITIG devices PULSE AC / DC should be done 200GD Æ si ę in an atmosphere free from components with r and smokers and Operation of devices and DIGITIG devices PULSE AC / DC should be done 200GD Æ si ę in an atmosphere free from components with r and smokers and Operation of devices and DIGITIG devices PULSE AC / DC should be done 200GD Æ... - Page 15 16. ELECTRIC SCHEME rocker switch CON10 CON12 AC220V CON4 CON13 CON11 CON2 Output + 25 * 15 * 12 CON3 ARC primer Bottom board CON8 PCON1 PZ01B-044-A magnet ring CON7 1234 MID-board 221 / 2KV 221 / 2KV 1234567 PD01B-011-D torch switch board CON5 Main transformer 22: 9 * 3...
- Page 16 DECLARATION OF CONFORMITY Ś 01 CI / DECLARATION OF CONFORMITY Ś 01 CI / DECLARATION OF CONFORMITY Ś 01 CI / DIGITIGPACDC200GD / 2017 authorized with manufacturer's representative: authorized with manufacturer's representative: authorized with manufacturer's representative: TECWELD Peter Polak 41-943 Piekary Ś l and State Street. 41-943 Piekary Ś...
Need help?
Do you have a question about the DIGITIG PULSE AC/DC 200GD and is the answer not in the manual?
Questions and answers