Advertisement
DTP DVI 301 • Setup Guide (Continued)
f
DVI Output connector (Rx) — Connect a display with a DVI input for display of the transmitted direct digital image.
g
Audio Output connector (Rx) — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the Audio
captive screw connector. See the drawing below.
Do not tin the wires!
CAUTION:
Connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (-) contacts.
h
Power connector — Connect an IEC power cord between the included 12 VDC power supply and a 100-240 VAC, 50-60 Hz
source. Connect the power supply to either unit as shown at right.
CAUTION:
This product is intended to be supplied by a Listed Power Unit
marked "Class 2" or "LPS," rated 12 VDC, 1.0 A minimum.
Always use a power supply supplied by or specified by Extron.
Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply
and the end product. Unless otherwise stated, the AC/DC
adapters are not suitable for use in air handling spaces or in
wall cavities. The installation must always be in accordance
with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 75 and the Canadian Electrical Code
part 1, section 16. The power supply shall not be permanently
fixed to a building structure or similar structure.
NOTE: Only one power supply is required. A single power supply
connected to either unit in the pair powers both units. A power
supply is included with each transmitter.
Operation
After all devices are powered up, the system is fully operational. See the
definitions of the power indications (shown at right), below:
a
Power LED (front panel) —
Amber — The unit is receiving power, either locally or remotely (on the
DTP cable).
Green — The unit is powered on and is receiving an active DVI signal, either on the DVI input if a transmitter, or transmitted on
the DTP cable if a receiver.
b
Power LED (rear panel) —
Amber — The unit is receiving power remotely (on the DTP cable).
Green — The unit is receiving power locally.
c
DC Route switch — This rear panel switch selects either the remote or local DVI display as the display data channel (DDC)
reference for EDID and HDCP communication.
If any problems are encountered, verify that the cables are routed and connected properly. If your problems persist, call the
Extron S3 Sales and Technical Support Hotline that is closest to you, at the number shown below.
Extron USA - West
Extron USA - East
Headquarters
+800.633.9876
+800.633.9876
Inside USA/Canada
Inside USA/Canada
Only
Only
+1.714.491.1500
+1.919.863.1794
+1.714.491.1517 FAX
+1.919.863.1797 FAX
2
Tip
Tip
Ring
Sleeve(s)
Sleeve(s)
Tip
Tip
Ring
Unbalanced Stereo Output
Balanced Stereo Output
Extron Europe
Extron Asia
+800.7339.8766
+800.3987.6673
Inside Asia Only
Inside Europe Only
+65.6383.4400
+31.33.453.4040
+65.6383.4664 FAX
+31.33.453.4050 FAX
© 2011 Extron Electronics. All rights reserved.
Smooth
A
SECTION A–A
1
Front
(Both Units)
Extron Japan
Extron China
+81.3.3511.7655
+400.883.1568
+81.3.3511.7656 FAX
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
www.extron.com
Ridges
A
Power Supply
Output Cord
DDC ROUTE
POWER
12V
0.7 A MAX
ON
SPARE
Rear
2
(Tx)
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max.
REMOTE
1
2
ANAL
LOCAL
3
68-2169-50
Rev A
08 11
Advertisement
