D-Link Web Smart DES-1210-28P Reference Manual
Web ui reference guide
Hide thumbs
Also See for Web Smart DES-1210-28P:
- Selection manual (6 pages) ,
- Specifications (6 pages) ,
- Reference manual (99 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for D-Link Web Smart DES-1210-28P
Summary of Contents for D-Link Web Smart DES-1210-28P
-
Page 3: Table Of Contents
File ... 14 Help ... 15 Device Configuration... 16 Add(+), Delete(-) and Discover the device ... 18 Device List... 18 Configuration ... 20 Smart Wizard Configuration... 20 Password Settings... 20 SNMP Settings ... 21 D-Link Web Smart Switch User Manual... - Page 4 Configuration > Spanning Tree > STP Global Settings... 48 Configuration > Spanning Tree > STP Port Settings ... 49 QoS > Storm Control ... 50 QoS > Bandwidth Control... 50 QoS > 802.1p/DSCP Priority Settings... 51 D-Link Web Smart Switch User Manual...
- Page 5 Appendix B - Technical Specifications ... 75 Hardware Specifications ... 75 Key Components / Performance ... 75 Port Functions ... 75 Physical & Environment ... 75 Emission (EMI) Certifications ... 75 Safety Certifications... 75 Features ... 75 D-Link Web Smart Switch User Manual...
- Page 6 Table of Contents L2 Features ... 75 VLAN ... 75 QoS (Quality of Service)... 76 Security... 76 Green... 76 Management... 76 Appendix C – Rack mount Instructions ... 77 D-Link Web Smart Switch User Manual...
-
Page 7: About This Guide
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. -
Page 8: Product Introduction
The intuitive SmartConsole easily allows customers to discover multiple D-Link web smart switches in the same L2 network segment. With this utility, users do not need to change the IP address of PC and provides easy initial setting of smart switches. -
Page 9: Des-1210-08P
Port Link/Act LED (1-8): The Link/Act LED lights up with solid green indicate a network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to the port. Reset: By pressing the Reset button the Switch will change back to the default configuration and all changes will be lost. -
Page 10: Rear Panel
CAUTION: The MiniGBIC ports should use UL listed Optical Transceiver product, Rated Laser Class I. 3.3Vdc. Reset: By pressing the Reset button the Switch will change back to the default configuration and all changes will be lost. Rear Panel Power: The power port is where to connect the AC power cord. -
Page 11: Rear Panel
When a port has amber light indicates that port is running on 10M or 100M. When it has a green light it is running on 1000M. Reset: Press the reset button to reset the Switch back to the default settings. All previous changes will be lost. -
Page 12: Rear Panel
CAUTION: The MiniGBIC ports should use UL listed Optical Transceiver product, Rated Laser Class I. 3.3Vdc. Rear Panel Power: Connect the supplied AC power cable to this port. D-Link Web Smart Switch User Manual Figure 8 – DES-1210-52 Rear Panel... -
Page 13: Hardware Installation
Rack Installation The switch can be mounted in an EIA standard size 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and secure them with the screws provided (please note that these brackets are not designed for palm size switches). -
Page 14: Step 3 - Plugging In The Ac Power Cord
(e.g. use of power strips)." Step 3 – Plugging in the AC Power Cord Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected). -
Page 15: Power Failure
Figure 13 – Plugging DES-1210-28/28P/52 into an outlet Power Failure As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in. Figure 12 – Plugging the DES-1210-08P into an outlet... -
Page 16: Getting Started
This chapter introduces the management interface of D-Link Web-Smart Switch. Management Options The D-Link Web Smart Switch can be managed through any port on the device by using the Web-based Management or through any PC using the SmartConsole Utility. Each switch must be assigned its own IP Address, which is used for communication with Web-Based Management or a SNMP network manager. -
Page 17: Login Web-Based Management
Spanish, French, Italian, Japanese and Russian. By default, the password is admin and the language is English. Smart Wizard After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart Switch. Please refer to Smart Wizard Configuration section for details. Web-based Management By clicking the Exit button in Smart Wizard, you will enter the Web-based Management interface. - Page 18 CD-Rom or DVD-Rom) and click OK. Follow the on-screen instructions to install the utility. Upon completion, go to Start > Programs > D-Link SmartConsole Utility and open the SmartConsole Utility. Connect the Smart Switch to the same L2 network segment of your PC and use the SmartConsole Utility to discover the Smart Switches.
-
Page 19: Smartconsole Utility
4 SmartConsole Utility SmartConsole Utility The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link smart switches which are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations of the switch. -
Page 20: Log
File By clicking on this icon you will see below options: Figure 19 – SmartConsole Log Figure 20 – SmartConsole Trap Icon Description No new traps New traps was received D-Link Web Smart Switch User Manual... -
Page 21: Help
4 SmartConsole Utility D-Link Web Smart Switch User Manual Figure 21 – SmartConsole File Monitor Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used. Monitor Save As: Records the setting of the Device List in an appointed filename and file path. -
Page 22: Device Configuration
Device List. Device Settings Select a switch from the Device List. Click on this icon to launch the Device Settings window. Here you can configure the Product Name, IP Address, Gateway, Subnet Mask, System Name, Location, Trap Host IP, Switch Group Interval, and DHCP Client Setting of the Switch. - Page 23 DHCP Refresh: If a DHCP-client enabled switch in the Device List shows the default IP is still used, it means the device did not receive an IP address from the DHCP server successfully. Select that switch and click the DHCP refresh icon.
-
Page 24: Add(+), Delete(-) And Discover The Device
4 SmartConsole Utility Web Access Select a switch from the Device List. Click this icon to launch your internet browser (eg. The Internet Explorer). Here you can configure the Switch through the Web-based Management utility. You may also get into the Web-based Management by double-clicking the device in the device list. - Page 25 Subnet Mask: Displays the Subnet Mask setting of the device. Gateway: Displays the Gateway setting of the device. Device Group Interval: Displays the intervals (in seconds) that the Switch will be discovered in the SmartConsole Device List Firmware version: Displays the current Firmware version of this device.
-
Page 26: Configuration
5 Configuration D-Link Web Smart Switch User Manual Configuration The features and functions of the D-Link Web Smart Switch can be configured for optimum use through the Web-based Management Utility. Smart Wizard Configuration After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart Switch. -
Page 27: Snmp Settings
5 Configuration D-Link Web Smart Switch User Manual SNMP Settings The SNMP Settings feature allows you to quickly enable or disable the SNMP function and configure the SNMP community name. For the complete SNMP feature, please navigate to Setup Menu > System >... -
Page 28: System Settings
System > System Settings”. The default setting of System IP address is Static. Select DHCP to have the switch obtain an IP address from a DHCP server in the network. Figure 32 – Configure System IP address in Smart Wizard NOTE: Changing the system IP address will disconnect you from the current connection. -
Page 29: Web-Based Management
Finally, by clicking on the D-Link logo at the upper-left corner of the screen you will be redirected to the local D-Link website. D-Link Web Smart Switch User Manual... -
Page 30: Tool Bar > Save Menu
The Tool Menu offers global function controls such as Reset, Reset System, Reboot Device, Configuration Backup and Restore, Firmware Backup and Upgrade. Reset Provide a safe reset option for the Switch. All configuration settings in non-volatile RAM will be reset to factory default except for the IP address. Reset System Provide another safe reset option for the Switch. -
Page 31: Reboot Device
Click Restore after selecting the backup settings file you want to restore. Firmware Backup and Upload Allow for the firmware to be saved, or for an existing firmware file to be uploaded to the Switch. Two methods can be selected: HTTP or TFTP. -
Page 32: Tool Bar > Smart Wizard
Tool Bar > Online Help The Online Help provides two ways of online support: Online Support Site will lead you to the D-Link website where you can find online resources such as updated firmware images; User Guide can offer an immediate reference for the feature definition or configuration guide. - Page 33 5 Configuration D-Link Web Smart Switch User Manual Figure 45 – User Guide Micro Site...
-
Page 34: Function Tree
D-Link Web Smart Switch User Manual Function Tree All configuration options on the switch are accessed through the Setup menu on the left side of the screen. Click on the setup item that you want to configure. The following sections provide more detailed description of each feature and function. -
Page 35: System > System Settings
5 minutes. Group Interval: The D-Link Web Smart Switch will routinely send report packets to the SmartConsole Utility in order to maintain the information integrity. The user can adjust the Group Interval to optimal frequency. -
Page 36: System > Port Settings
(From Port and To Port), the Speed can be set for all selected ports, effective by clicking Apply. Press the Refresh button to view the latest information. D-Link Web Smart Switch User Manual Figure 50 – System > Trap Setting... -
Page 37: System > Snmp Settings > Snmp Global State
Switch to other networking devices, a crossover cable must be used. This switch provides configurable MDI/MDIX function for users. The switches can set as an MDI port in order to connect to other hubs or switches without an Ethernet crossover cable. -
Page 38: System > Snmp Settings > Snmp User Table
This page is used to maintain the SNMP user table for the use of SNMPv3. SNMPv3 allows or restricts users using the MIB OID, and also encrypts the SNMP messages sent out between users and Switch. User Name: Enter a SNMP user name of up to 32 characters. -
Page 39: System > Snmp Settings > Snmp View Table
5 Configuration AuthPriv – Both authorization and encryption are required for packets sent between the Switch and SNMP manger. Notify View Name: Specify a SNMP group name for users that can receive SNMP trap messages generated by the Switch's SNMP agent. -
Page 40: System > Snmp Settings > Snmp Host Table
System > SNMP Settings > SNMP Engine ID The Engine ID is a unique identifier used to identify the SNMPv3 engine on the Switch. Input the Engine ID then click Apply to apply the changes and click Default resets to default value. -
Page 41: System > Password Access Control
Figure 59 – System > SNMP Settings > SNMP Trap Setting System > Password Access Control Setting a password is a critical tool for managers to secure the Web-Smart Switch. After entering the old password and the new password two times, click Apply for the changes to take effect. - Page 42 5 Configuration D-Link Web Smart Switch User Manual You may change the name accordingly to the desired groups, such as R&D, Marketing, email, etc. Figure 62 – Configuration > 802.1Q VLAN > Default Setting Figure 63 – Configuration > 802.1Q VLAN > Add VID Figure 64 –...
-
Page 43: Configuration > 802.1Q Vlan (Asymmetric Vlan)
VLAN 2 is configured to include ports 15-18, 20 (shared VLAN ports) and the set of ports to be separated from the other VLANs (for example, port 5). VLAN 3 and 4 are then configured to include D-Link Web Smart Switch User Manual Firewall, V1~V4... -
Page 44: Configuration > 802.1Q Management Vlan
Configuration > 802.1Q Management VLAN The 802.1Q Management VLAN setting allows you to transfer the authority of the switch from the default VLAN to others created by users. This allows managing the whole network more flexible. -
Page 45: Configuration > Voice Vlan > Voice Vlan Settings
From Port / To Port: A consecutive group of ports may be configured starting with the selected port. Auto Detection: Switch will add ports to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI configured in Voice VLAN OUI Setting page. Use the drop-down menu to enable or disable the OUI auto detection function. -
Page 46: Configuration > Voice Vlan > Voice Vlan Oui Setting
Similar as Voice VLAN, Auto Surveillance VLAN is a feature that allows you to automatically place the video traffic from D-Link IP cameras to an assigned VLAN to enhance the IP surveillance service. With a higher priority and individual VLAN, the quality and the security of surveillance traffic are guaranteed. The Auto Surveillance VLAN function will check the source MAC address / VLAN ID on the incoming packets. -
Page 47: Configuration > Link Aggregation > Port Trunking
Auto Voice VLAN is also enabled to guarantee the quality of VoIP traffic. Component Type: Surveillance VLAN will automatically detect D-Link Surveillance Devices by default. There are another five surveillance components that could be configured to be auto-detected by surveillance VLAN. -
Page 48: Configuration > Link Aggregation > Lacp Port Settings
Configuration > Link Aggregation > LACP Port Settings The LACP Port Settings is used to create port trunking groups on the Switch. The user may set which ports will be active and passive in processing and sending LACP control frames Figure 75 –... -
Page 49: Configuration > Igmp Snooping
Click Apply to implement the changes made. Configuration > IGMP Snooping With Internet Group Management Protocol (IGMP) snooping, the Web Smart Switch can make intelligent multicast forwarding decisions by examining the contents of each frame’s Layer 2 MAC header. IGMP snooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the Web Smart Switch will forward multicast traffic only to connections that have group members attached. -
Page 50: Configuration > Multicast Filtering Mode (For Des-1210-08P Only)
It also allows adjustments for controlling the frequency of IGMP traffic on a subnet. Default is 10 seconds. Querier State: D-Link Smart Switch is able to send out the IGMP Queries to check the status of multicast clients. Default is disabled. -
Page 51: Configuration > Multicast Filtering Mode (For Des-1210-28/28P/52)
Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied. This enables network managers to better monitor network performances. -
Page 52: Configuration > Sntp Settings > Time Settings
Configuration > SNTP Settings > Time Settings SNTP or Simple Network Time Protocol is used by the Switch to synchronize the clock of the computer. The SNTP settings folders contain two windows: Time Settings and TimeZone Settings. Users can configure the time settings for the switch, and the following parameters can be set or are displayed in the Time Settings page. -
Page 53: Configuration > Sntp Settings > Timezone Settings
Local - Indicates that the system time is set locally by the device. SNTP - Indicates that the system time is retrieved from a SNTP server. Current Time: Displays the current date and time for the switch. If choosing SNTP for the clock source, then the following parameters will be available: SNTP First Server: Specify the IP address of primary SNTP server from which the system time is retrieved. -
Page 54: Configuration > Spanning Tree > Stp Global Settings
Root Bridge, the Switch will start sending its own BPDU to all other switches for permission to become the Root Bridge. If it turns out that the Switch has the lowest Bridge Identifier, it will become the Root Bridge. -
Page 55: Configuration > Spanning Tree > Stp Port Settings
STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use on the switch level, the Switch allows for the configuration of groups of ports, each port-group of which will have its own spanning tree, and will require some of its own configuration settings. -
Page 56: Qos > Storm Control
The Storm Control feature provides the ability to control the receive rate of broadcast, multicast, and unknown unicast packets. Once a packet storm has been detected, the Switch will drop packets coming into the Switch until the storm has subsided. -
Page 57: Qos > 802.1P/Dscp Priority Settings
The following figure displays the status of Quality of Service priority levels of each port, higher priority means the traffic from this port will be first handled by the switch. For packets that are untagged, the switch will assign the priority depending on your configuration. - Page 58 Figure 90 – QoS > DSCP Priority Settings Select QoS Mode: D-Link Smart Switch allows the user to prioritize the traffic based on the 802.1p priority in the VLAN tag or the DSCP (Differentiated Services Code Point) priority in the IP header. Only one mechanism is selected to prioritize the packets at a time.
-
Page 59: Security > Trusted Host
To delete the IP address simply click the Delete button, check the unwanted address, and then click Apply. Security > Safeguard Engine D-Link’s Safeguard Engine is a robust and innovative technology that automatically throttles the impact of packet flooding into the switch's CPU. This function helps protect the Web-Smart Switch from being interrupted by malicious viruses or worm attacks. -
Page 60: Security > Port Security
This page allows you to configure the SSL global state and the Ciphersuite settings. Select Enable or Disable and then click Apply to change the SSL state or the Ciphersuite settings of the Switch. By default, SSL is Disabled and all Ciphersuites are Enabled. -
Page 61: Security > 802.1X > 802.1X Settings
EAP Request/Identity packet transmitted to the client. Default is 24 seconds. ReAuthEnabled: This function is to determine whether regular re-authentication will take place on this port(s). When the 802.1X function is enabled, the switch sends an EAP-request/identity packet to client. The ReAuthEnabled function is by default disabled. -
Page 62: Security > Mac Address Table > Static Mac
SuppTimeout (1 – 65535 sec): This value determines timeout conditions in the exchanges between the Authenticator and the client. Default is 12 seconds. ServerTimeout (1 – 65535 sec): Sets the amount of time the switch waits for a response from the client before resending the response to the authentication server. Default is 16 seconds. -
Page 63: Security > Mac Address Table > Dynamic Forwarding Table
Security > MAC Address Table > Dynamic Forwarding Table For each port, this table displays the MAC address learned by the Switch. To add a MAC address to the Static Mac Address List, click the Add checkbox, and then click Apply associated with the identified address. - Page 64 5 Configuration D-Link Web Smart Switch User Manual Figure 97 – Monitoring > Statistics Refresh All: Renews the details collected and displayed. Clear All Counters: To reset the details displayed. TxOK: Number of packets transmitted successfully. RxOK: Number of packets received successfully.
-
Page 65: Monitoring > Cable Diagnostics
‧Test Failed means some other errors occurred during cable diagnostics. Please select the same port and test again. Cable Fault Distance (meters): Indicates the distance of the cable fault from the Switch port, if the cable is less than 2 meters, it will show “No Cable”. -
Page 66: Acl > Acl Configuration Wizard
ACL > ACL Configuration Wizard Access Control List (ACL) allows you to establish criteria to determine whether or not the Switch will forward packets based on the information contained in each packet's header. These criteria can be specified on a basis of MAC address, or IP address. -
Page 67: Acl > Acl Profile List
Show Details: To display an ACL’s profile details. The ACL profile details are displayed below the ACL table. Show Rules: To show the access rule in this profile. D-Link Web Smart Switch User Manual Figure 102 – ACL > ACL Profile List... - Page 68 3) After the Profile ID has been created, it will go back to the main Access Profile List page, clicking the Edit / New Rules button to enter Access Rule List page. D-Link Web Smart Switch User Manual Figure 103 – Add Access Profile...
- Page 69 Source IP Address: Specify the Source IP address. DSCP: Specify the DSCP value. IP Protocol: The L4 protocol above IP. Possible values are ICMP, IGMP, TCP, and UDP. D-Link Web Smart Switch User Manual Figure 104 – Access Rule List Figure 105 – Add Access Rule...
-
Page 70: Acl > Acl Finder
Destination Port: Specify the TCP or UDP destination port value. TCP Flag: Specify the TCP flag value. Ports: Specify the switch ports that you want to implement the access rule to. Action: Specify the ACL forwarding action matching the rule criteria. Permit is to forward packets if all other ACL criteria are met. -
Page 71: Poe > Poe System Settings (Only For Des-1210-08P/28P)
This page allows you to configure the global PoE settings of the device and also displays current PoE status including System Budget Power, Support Total Power, Remainder Power, and The ratio of system power supply. D-Link Web Smart Switch User Manual Current power Figure 108 –... -
Page 72: Time-Based Poe > Time Range Settings (Only For Des-1210-08P/28P)
LLDP devices. The Switch will store that information in the Management Information Base (MIB); SNMP utilities can learn about the network topology by getting the MIB information from each LLDP device. -
Page 73: Lldp > Lldp Remote Port Information (Only For Des-1210-08P/28P)
Click << Back to return to the previous page. Figure 111 – LLDP > LLDP Global Settings Figure 112 – LLDP > LLDP Remote Port Information Figure 113 – LLDP > LLDP Remote Port Information D-Link Web Smart Switch User Manual... -
Page 74: Lldp > Lldp-Med Settings (Only For Des-1210-28P)
5 Configuration D-Link Web Smart Switch User Manual LLDP > LLDP-MED Settings (Only for DES-1210-28P) LLDP-MED (Link Layer Discovery Protocol-Media Endpoint Discovery) is an enhancement of LLDP. It improves the LLDP operation between endpoint devices such as IP phones and APs. LLDP-MED supports features such as Auto-discovery of LAN policies and device location discovery. -
Page 75: Command Line Interface
6 Command Line Interface Command Line Interface The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol. To connect a switch via TELNET: 1. -
Page 76: Upload
6 Command Line Interface firmware_fromTFTP cfg_fromTFTP tftp://ip-address/ filename Upload The upload command is used to upload the firmware file or a Switch configuration file to a TFTP server. Syntax upload firmware_toTFTP tftp://ip-address/filename } Parameters Parameter firmware_toTFTP cfg_toTFTP tftp://ip-address/ filename Config ipif system The config ipif system command sets the IP address of the switch. -
Page 77: Logout
This command checks if another IP address is reachable on the network. You can ping the IP address connected to through the managed VLAN (VLAN 1 by default), as long as there is a physical path between the switch and the target IP equipment. By default, Switch sends five pings to the target IP. -
Page 78: Reset
DES-1210-28P> Config account admin password The command sets the administrator password. Syntax config account admin password <passwd> D-Link Web Smart Switch User Manual Figure 120 – The reboot command Figure 121 – The reset config command : Static : 172.17.5.214 : 255.255.255.0... -
Page 79: Save
The command saves the configuration changes to the memory. Syntax save Example DES-1210-28P> save Building configuration ... [OK] DES-1210-28P> Debug info This command displays the ARP table and MAC FDB of the Switch. Syntax debug info Example DES-1210-28P> debug info % ARP table : Address Hardware Address ------- ---------------- 172.17.5.85... -
Page 80: Appendix A - Ethernet Technology
Appendix A - Ethernet Technology Appendix A - Ethernet Technology This chapter will describe the features of the D-Link Web Smart Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Gigabit Ethernet Technology Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, and management objects, but with a tenfold increase in theoretical throughput of over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet. -
Page 81: Appendix B - Technical Specifications
- DEM-210 (100BASE-FX, 15km) - DEM-211 (100BASE-FX, 2km) WDM Transceivers Supported: - DEM-330T (1000Base-BX,TX-1550/RX- 1310nm, 10km) - DEM-330R (1000Base-BX,TX-1310/RX- 1550nm, 10km) D-Link Web Smart Switch User Manual - DEM-331T (1000Base-BX,TX-1550/RX- 1310nm, 40km) - DEM-331R (1000Base-BX,TX-1310/RX- 1550nm, 40km) - DEM-220T (100Base-BX, TX-1550/RX- 1310nm, 20km) -
Page 82: Qos (Quality Of Service)
LLDP-MED (DES-1210-28P only) Trap setting for destination IP, system events, fiber port events, twisted-pair port events Port access control Web-based configuration restoration Web-based firmware backup/restore Firmware upgrade using SmartConsole Utility & Web-based management Reset, Reboot D-Link Web Smart Switch User Manual backup... -
Page 83: Appendix C - Rack Mount Instructions
Appendix C – Rack mount Instructions D-Link Web Smart Switch User Manual Appendix C – Rack mount Instructions Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.