DU9800Z DLP Projector Remote Communication Manual Table of Contents The Serial Interface RS-232 Command ..................2 Communication parameter ......................2 Operation commands ......................... 2 Operation command syntax ....................2 List of operation commands ....................3 Simulated IR remote controller commands ................15 List of simulated IR remote controller commands ..............
DU9800Z DLP Projector Remote Communication Manual The Serial Interface RS-232 Command This projector supports to control by RS-232 command, there exist two types of RS-232 serial commands: Operation command: Available menu options are INPUT, PICTURE, ALIGNMENT, CONTROL and SERVICE. ...
DU9800Z DLP Projector Remote Communication Manual List of operation commands INPUT OSD Function Operation Settings/Return Values Note command Input Select input.sel 0 = HDMI 1 Not applicable when the project is at 1 = HDMI 2 standby mode 2 = VGA...
Page 5
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command VGA Setup/H Phase h.phase 0-200 Available when the source is locked. Input source is VGA or Component(RGBHV) VGA Setup/V Start v.pos 0-200 Available when the source is locked.
Page 6
DU9800Z DLP Projector Remote Communication Manual Operation OSD Function Settings/Return Values Note command 0-200 Apply for YUV signal input tint Not applicable if the input signal is not locked yet. Sharpness sharp 0-15 Not applicable when the project is in standby mode or the input signal is not locked yet.
Page 7
DU9800Z DLP Projector Remote Communication Manual Operation OSD Function Settings/Return Values Note command 0-200 Available when the input source is HSG/Blue Gain hsg.b.gain locked. HSG/Cyan Gain hsg.c.gain 0-200 Available when the input source is locked. 0-200 Available when the input source is HSG/Magenta Gain hsg.m.gain...
Page 8
DU9800Z DLP Projector Remote Communication Manual Operation OSD Function Settings/Return Values Note command 0-200 Available when the input source is HSG/Magenta/Hue hsg.m. hue locked. HSG/Yellow/Hue Hsg.y. hue 0-200 Available when the input source is locked. 0-200 Available when the input source is HSG/White/Red Gain hsg.wr.gain...
Page 9
DU9800Z DLP Projector Remote Communication Manual Alignment OSD Function Operation Settings/Return Value Note command Lens control zoom.in (execute) Not applicable when the projector is Zoom at standby mode Lens control zoom.in.2 (execute) Not applicable when the projector is Zoom at standby mode.
Page 10
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Value Note command Lens control lens.right.3 (execute) Not applicable when the projector is Lens right at standby mode. Lens Memory / lens.load 1-10 set of lens memory Not applicable when the projector is...
Page 11
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Value Note command Warp / Keystone H h.keystone Horizontal -600 ~ + 600 Available when active.warp is set to 1 (keystone) or 4 (Pincushion) Warp / Keystone V v.keystone Vertical -400 ~ + 400 ...
Page 12
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Value Note command Edge Blend / eb.top 0 100~500 Available when Edge Blend is set to White Level On (eb.stat =1). Edge Blend / eb.bottom 0 100~500 Available when Edge Blend is set to White Level On (eb.stat =1).
Page 13
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Auto Power On auto.powon 0 = Off Not available when the projector is 1 = On at standby mode. Network/ Standby lan.power 0 = Off Not applicable when the project is at...
Page 14
DU9800Z DLP Projector Remote Communication Manual OSD Function Operation Settings/Return Values Note command Trigger trig.1 0 = Off Not applicable when the projector is 1 = Screen at standby mode. 2 = 5:4 3 = 4:3 4 = 16:10 5 = 16:9 6 = 1.88...
Page 15
DU9800Z DLP Projector Remote Communication Manual Others Function Operation Settings/Return Values Note command Power On power.on (execute) Power Off power.off (execute) Projector Status status 0 = Standby 1 = Warm Up 2 = Imaging 3 = Cooling 4 = Error...
DU9800Z DLP Projector Remote Communication Manual Simulated IR remote controller commands This control command simulates the IR remote controller and its control keys. It shares the same syntax of operation command. It begins with characters "ky", followed by control commands and settings separated by space blank [SP], and ended by carriage return pair "CR"...
DU9800Z DLP Projector Remote Communication Manual Control the Projector Through a Network This machine supports the following methods in remotely controlling the projector through a network: Control projector through web browser. Control projector with RS-232 control or simulated IR commands via TCP/IP communication protocol.
DU9800Z DLP Projector Remote Communication Manual Set up the projector for networking Before performing projector control by network, please configurate the network setting and make sure Standby Power is set to On. Network Mode: Switch network mode for projector control or service, the default setting is Projector Control.
DU9800Z DLP Projector Remote Communication Manual Control the projector through a network Control the projector through a web browser Open the web browser of your control PC; type the projector's IP address. The left of the web page shows below four options: Projector Status: Display current projector settings.
Page 20
DU9800Z DLP Projector Remote Communication Manual Projector Control This page provides the control buttons for power, blank, Input Selection and Lens control. Power : Projector power on/off control. Blank : Interrupt the projection temporarily or start the projection again. Input Selection : Select the input source by pressing the buttons.
Page 21
DU9800Z DLP Projector Remote Communication Manual Crestron RoomView This page shows Crestron control page for projector control, the available options are as below options. Power: Press this button to turn power on or off. Source List: Switch projector input sources. Press the ▲ or ▼ arrow key to scroll through the dropdown list of...
Page 22
DU9800Z DLP Projector Remote Communication Manual Control key window This window simulates keys on the remote controller and control panel. Enter: Confirm and select function options Menu: Press to display OSD menu. Press again to exit it. Auto: Run the auto image adjustment function.
DU9800Z DLP Projector Remote Communication Manual Alert Mail Setup This projector can send emails with projector abnormality messages to preset users. Set up the projector before enabling this function: SMTP Server : Set up SMTP server name. Port : Set up port name.
DU9800Z DLP Projector Remote Communication Manual About Vivitek Support If you cannot find solutions from this user guideline, please contact us using the contact information below: Europe, Middle East and Africa Vivitek Service & Support Zandsteen 15 2132 MZ Hoofddorp...