Advertisement
@crown
* System
@crown
* System
®
®
Rotate PIP2 180°
18 PIN (B)
B
20 PIN (A)
A
Plug In CABLE A
B
OUT
BUS
Plug In CABLE B
A
B
20 PIN (A)
OUT
BUS
Rotate PIP2 180° in
opposite direction
SLM #.#
IN
AUD IO
CH- 2
Slide PIP2 Into Amplifier
IN
AUD IO
CH- 2
2
PIP
Installation
®
®
Product Reference
Product Reference
P.I.P.-SLM (Page 3 of 3)
—Sweep Resolution
—Sweep Start Frequency
—Sweep Stop Frequency
—Oscillator Frequency
—Generator Amplitude
—Acquisition Mode
—Start/Abort Sweep
CRO WN BUS
DATA
—Impedance Response Tolerance
AUX
SLM #.#
##
IN
OUT
OUT IN
AUD IO
IN
CH- 1
CH- 2
—Frequency Response Tolerance
—Report Pass-Fail at Aux
—Start/Abort Via Aux
SOFTWARE SUPPORT
The P.I.P.-SLM is supported by the
Turbo 1.4, and Sys-Config II DOS soft-
18 PIN (B)
ware packages as well as the IQ For
20 PIN (A)
Windows software package.
A
P.I.P.-SLM SPECIFICATIONS
2
CH-
CH-
1
IO
AUD
OUT
IN
IN
IN
SLM
#.#
##
AUX
Audio specifications are referenced to
DATA
WN
CRO
0 dBu, measurements taken at the edge
connector of the module itself.
Aux Port:
Aux Port: Pin 1 is tied to ground. Pin 2 is
Aux Port:
Aux Port:
Aux Port:
a sensing input capable of sensing an
analog voltage or digital state. Pin 3 is
high impedance when switched off from
18 PIN (B)
software, +15 VDC at 15 ma when
switched on from software.
2
CH-
CH-
1
IO
AUD
OUT
IN
IN
IN
SLM
#.#
##
AUX
DATA
CRO
WN
CRO WN BUS
DATA
AUX
##
OUT
IN
OUT IN
CH- 1
CRO WN BUS
DATA
AUX
##
SLM #.#
OUT
IN
OUT IN
CH- 1
Power Requirements:
Power Requirements:
Power Requirements: Unregulated
Power Requirements:
Power Requirements:
±24VDC from amplifier.
Memory Backup:
Memory Backup:
Memory Backup:
Memory Backup: EEPROM maintains
Memory Backup:
memory with amplifier power off. Rated
at greater than 10,000 writes. Changes
are written to EEPROM memory ap-
proximately 30 seconds after the last
command to change a setting is re-
ceived.
Data Rate:
Data Rate:
Data Rate: 38,400 baud.
Data Rate:
Data Rate:
Data Format:
Data Format:
Data Format:
Data Format: Serial, binary, asynchro-
Data Format:
nous, 1 start bit, 1 stop bit, 8 data bits,
no parity.
Data Protocol:
Data Protocol:
Data Protocol:
Data Protocol:
Data Protocol: IQ
Interface Type:
Interface Type:
Interface Type:
Interface Type: Isolated 20 ma current
Interface Type:
loop.
Operation:
Operation:
Operation: Half duplex.
Operation:
Operation:
Intelligence:
Intelligence:
Intelligence: 8 bit processor with 20 KB
Intelligence:
Intelligence:
firmware.
Input Impedance:
Input Impedance: Nominally 20K Ohm
Input Impedance:
Input Impedance:
Input Impedance:
balanced, 10K Ohm unbalanced.
Signal/Noise:
Signal/Noise:
Signal/Noise:
Signal/Noise: >85 dB 20 to 22 kHz.
Signal/Noise:
Frequency Response:
Frequency Response:
Frequency Response:
Frequency Response:
Frequency Response: ±0.1 dB 20 to 22
kHz.
Crosstalk:
Crosstalk:
Crosstalk:
Crosstalk:
Crosstalk: >70 dB at 1 kHz, >65 dB at
20 kHz.
T.H.D.:
T.H.D.:
T.H.D.:
T.H.D.:
T.H.D.: <0.05% 20 to 22 kHz.
Guaranteed Excellence
@crown
Crown International, Inc.
PO Box 1000 Elkhart, IN 46515-1000
Ph. 800-342-6939/219-294-8200
Fax 219-294-8301
Internet: www.crownaudio.com
Trademark Notice:
Trademark Notice:
Trademark Notice:
Trademark Notice:
Trademark Notice:
IQ System
®
and P.I.P.
®
are registered
trademarks of Crown International Inc.
2
protocol.
Advertisement
