Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axminster UE-125DV
Summary of Contents for Axminster UE-125DV
-
Page 2: Table Of Contents
Table of Contents General Safety Rules ......................1 Electrical schematic ......................... 2 Before cutting and pump grease ....................3 The Quick Vise and Work Set Up ..................3 Usage of the vise ........................3 Work set up ..........................3 Special Safety Rules for Metal Saw ..................4 Before using the saw ....................... -
Page 3: General Safety Rules
1. General Safety Rules WARNING Read and understand instructions of this manual entirely before operating the machine. Always wear approved safely glasses /face shields when using the machine. Make certain the machine is properly grounded. Before machine in operation, remove tie, ring, watch, other jewelry, and roll your sleeves up to above elbows. -
Page 4: Electrical Schematic
Electrical Schematic - 2 -... -
Page 5: Before Cutting And Pump Grease
2. The Quick Vise and Work Set BEFORE CUTTING Release the lock pin (A) in Fig.1 to free this Usage of the Vise saw. After service, must relock in the pin properly for your safety and carry. Failure to comply with the warning could result in The vise is mounted on the machine base. -
Page 6: Special Safety Rules For Metal Saw
3. Special Safety Rules for Metal aluminum, wood, plastic and so ˙ Make sure the direction of rotation arrow on the blade matches the direction arrow on the saw. The blade teeth should always point WARNING: For your own safety, do not downward at the front of the saw. -
Page 7: Whenever Saw Is Running
To avoid injury from accidental starting, always unplug saw before WARNING: Read the following warning disconnecting the guard, installing or labels found on the front of the saw. removing any blade, accessory or attachment, or making any adjustment. To avoid an electrical shock, make sure your fingers do not touch the DANGER metal prongs on the plug when... -
Page 8: Motor Safety Protection
supply circuit) or to overly long supply circuit wire. Always check the connections, DANGER: To avoid electric shock the load and the supply circuit whenever 1. Do not change the power cord and motor doesn’t work well. Check wire size plug to another specification not and length with the Wire Size Chart below. -
Page 9: Description And Characteristics
6. Description and Characteristics 7. Operating This 125DV portable band saw is made as Information before Operation light as 21 kg by weight for your fitness to transport to any worksites. Be sure the blade isn’t in contact with the work This machine frame is cast by the when the motor is started. -
Page 10: Angle Cutting
Angle Cutting Remove the blade guard by loosening two screws (U) in Fig. 9 on the saw frame. The machine uses a swivel miter base for angle cutting from 0 ~60 degree. On the sawing arm, there is an attached scale (Q) in Fig.7. This machine is preset zero degree before leaving the factory. -
Page 11: Magnetic Switch
Remove blade from both wheels and blade 8. Adjusting guides bearings in Fig.12. Adjusting Blade Guide An unbounded handle (A) in Fig.14 is mounted on the unit for freely changing blade guide device position by loosens it counter- clockwise. Fig. 12 Blade guides bearings Place a new blade on the wheels but not too tight, twist blade slightly and let it slip... -
Page 12: Changing The Motor Carbon Brushes
Fig. 17 Fig. 15 Fig. 18 Fig. 16 WARNING Fig. 19 SHUT OFF THE POWER SOURCE BEFORE THIS MACHINE IS IN ADJUSTMENT, MAINTENANCE, OR REPAIRMENT. Changing the Motor Carbon Brushes If the motor is making an unusual noise then the carbon brushes may need to be replaced. -
Page 13: Part List & Explosion Drawings
- 11 -... - Page 14 - 12 -...
- Page 15 - 13 -...
- Page 16 - 14 -...
Need help?
Do you have a question about the UE-125DV and is the answer not in the manual?
Questions and answers