Page 1
TP200 PANEL User Guide Standard Menu Your Single Source Solution 42369 Rev A1...
Page 2
This user guide applies to TP200, TP240 and TP260 panels. THANK YOU TP200 PANEL for using Balboa Water Group spa controls. TP240 PANEL TP260 PANEL Please visit us at BP CONTROL SYSTEM www.BalboaWaterGroup.com Software Version: 7.0 and later...
REMINDER DASHED LINE AROUND THE DISPLAY Dashed lines indicate a Menu item that depends on a manufacturer configuration and may or may not appear. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Temperature. Two, you can navigate menus by pressing the LIGHT button. If you do not Utilities press any buttons for a few moments, the Main Screen will appear automatically. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
TIME Menu until the time is actually set, but reverse direction. since the spa started at noon, the filter cycles will run as programmed. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Cycle 2 will end at 11:00 AM. Press the LIGHT button, and the Main Screen will appear. Or, pause a moment, and the Main Screen will appear automatically. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Page 7
Menu Items may or may not appear appear automatically. If you do not press LIGHT, your setting will not be saved, and the Main Screen will appear momentarily. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Page 8
Menu Items may or may not appear If you do not press LIGHT, your setting will not be saved, and the Main Screen will appear momentarily. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Pause / back to Main Screen / setting saved Mode is done. After a moment Menu Items may or may not appear the Main Screen will appear automatically. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Press LIGHT to save your setting, and RUN HRS will appear. This message means you are about to set the duration. Use the same sequence to set the duration. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
3°F (1.5°C) above the set temperature (most likely to happen in very hot climates). MODE 2: The circulation pump will stay on continuously, regardless of the water temperature. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
In-Rest Mode for one hour. and Low ranges. During this hour the control system will attempt to keep the water temperature close to the Set Temperature. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Page 13
The Main Screen will alternate between displaying the Pause / back to Main Screen / setting saved water temperature and RRST. Menu Items may or may not appear Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Fault Log information. For example, this Message Code (B) will appear in the corresponding Fault Log. See how to review the Fault Log on page 55. Panel Message Message Code Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code. This message can be reset from the panel with any button press. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE...
View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code. This message can be reset from the panel with any button press. This message can be reset from the panel with any button press. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code. This message can be reset from the panel with any button press. This message can be reset from the panel with any button press. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code. This message can be reset from the panel with any button press. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE...
View page 55 for instructions on how to review the Fault Log that corresponds with the Message Code. This message can be reset from the panel with any button press. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE...
Page 21
Wood skirting and furniture should be cleaned Filters should be replaced occasionally to and conditioned per the manufacturers maintain proper spa function and instructions for maximum life. sanitary conditions. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Main Screen will appear automatically, and the will appear automatically. Or Press LIGHT address number will remain 0. to navigate the menu. Press TEMP again to change the address number (0-7). Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Press LIGHT to view UTIL. Or, pause a moment and the Main Screen will appear. Press LIGHT to view UTIL. Or, pause a moment and the Main Screen will appear. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
3.0 hours. Press LIGHT to save your setting, and PREF will appear. Press LIGHT to view UTIL. Or, pause a moment and the Main Screen will appear. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
16 indicates that it is showing 6 DIP store settings, memory reset switches that are numbered 1 - 6. N/A or special amperage rule This is the panel software version. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
If manually. the GFCI does not reset and freezing conditions exist, drain the spa of all water until the spa is functional again. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Page 29
This indicates that the GFCI is armed. Press LIGHT to navigate back to TRIP. Or, pause a moment, and the Main • • • Screen will appear automatically. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
B. Press LIGHT to navigate back °°° °°° °°° to the fault number. Or, pause a moment and the Main Screen will appear automatically. Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
The Main Screen displays temperature readings from sensor A and sensor B, until you turn Off this feature. Follow the same sequence to turn Off this feature. Heater Balboa Water Group | Your Single Source Solution TP200 USER GUIDE 42369 Rev A2...
Page 32
Balboa Water Group or its respective • Disconnect the electrical power before servicing. Warning: To avoid injury, exercise care when entering suppliers relating to the Balboa Water Group BP Spa Control Systems, Attention: or exiting the spa or hot tub.
Page 33
M - F 7:00AM to 6:00PM PT Costa Mesa, CA 92626 MEXICO OPERATIONS EUROPEAN OPERATIONS Balboa Water Group Balboa Water Group Aguila Azteca 6011 Hydroair International Baja Maq. El Aquila ApS Roustvej 50 DK-6800 Mexico 22221 Varde Balboa Water Group | Your Single Source Solution...