Grizzly T30945 Owner's Manual
  1. Manuals
  2. Brands
  3. Grizzly Manuals
  4. Saw
  5. T30945
  6. Owner's manual

Grizzly T30945 Owner's Manual

7" benchtop tile saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL T30945
7" BENCHTOP TILE SAW
OWNER'S MANUAL
(For models manufactured since 12/19)
COPYRIGHT © FEBRUARY, 2020 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CS20849 PRINTED IN CHINA
V1.02.20

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T30945 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Grizzly T30945

Summary of Contents for Grizzly T30945

  • Page 1 (For models manufactured since 12/19) COPYRIGHT © FEBRUARY, 2020 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #CS20849 PRINTED IN CHINA V1.02.20...
  • Page 2 This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

  • Page 3: Table Of Contents

    Table of Contents INTRODUCTION ..........2 SECTION 5: ACCESSORIES ......25 Contact Info............ 2 SECTION 6: MAINTENANCE ......27 Manual Accuracy ........... 2 Schedule ............27 Identification ........... 3 Cleaning & Protecting ........27 Controls & Components ......... 4 Lubrication ........... 27 Machine Data Sheet ........

  • Page 4: Introduction

    Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equip- Manufacture Date ment, or poor work results. Serial Number Model T30945 (Mfd. Since 12/19)

  • Page 5: Identification

    Use tool only with smooth edge blades free of openings and grooves. e) Replace damaged blades before operating. f) Do not fill water bath above water fill line. Model T30945 (Mfd. Since 12/19)

  • Page 6: Controls & Components

    D. Splash Hood: Protects user from rotating to water bath. blade and helps contain overspray. Overflow Drain Plug: Drains excess water E. Rear Support: Provides ripping support for and removes to drain water bath. larger tiles up to 24". Model T30945 (Mfd. Since 12/19)

  • Page 7: Machine Data Sheet

    Table Tilt Stops ............................22.5, 45 deg. Maximum Supported Length of Cut .........................24 in. Maximum Depth of Cut ............................1-1/4 in. Diagonal Capacity ..............................12 in. Required Blade Body Thickness ...........................0.05 in. Model T30945 (Mfd. Since 12/19) Model T30945 Page 1 of 2...
  • Page 8 Ribbed Table w/Water Return Trough 10" Infeed/Outfeed Scale Tilt Table w/22.5 & 45 Deg. Support Stops Adjustable Splash Hood 2.3L Water Bath Accessories: 7" Diamond Blade 8mm Arbor Wrench 19mm Closed-End Wrench Model T30945 (Mfd. Since 12/19) Page 2 of 2 Model T30945...

  • Page 9: Section 1: Safety

    Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model T30945 (Mfd. Since 12/19)
  • Page 10 Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. Model T30945 (Mfd. Since 12/19)

  • Page 11: Additional Safety For Tile Saws

    Always support/feed small or narrow workpieces to machine. Reduce cutting force if you hear any with miter guide, push stick, push blocks, jig, vise, strain on motor. or some type of clamping fixture. Model T30945 (Mfd. Since 12/19)

  • Page 12: Section 2: Power Supply

    -10- Model T30945 (Mfd. Since 12/19)
  • Page 13 Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -11- Model T30945 (Mfd. Since 12/19)

  • Page 14: Section 3: Setup

    IMPORTANT: Save all packaging materials until you are completely satisfied with the machine and have resolved any issues between Grizzly or the shipping agent. You MUST have the original pack- aging to file a freight claim. It is also extremely helpful if you need to return your machine later.

  • Page 15: Hardware Recognition Chart

    Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -13- Model T30945 (Mfd. Since 12/19)

  • Page 16: Assembly

    (see Lift and remove bevel table. Figure 9). Install blade as instructed in Removing & Installing Blade on Page 24. Overflow Drain Plug Figure 9. Overflow drain plug installed. -14- Model T30945 (Mfd. Since 12/19)

  • Page 17: Site Considerations

    Figure 12. Minimum working clearances. Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use. -15- Model T30945 (Mfd. Since 12/19)

  • Page 18: Bench Mounting

    DO NOT pull by the receptacle, and your hands are dry. cord as this may damage the wires inside. Lag Screw Flat Washer Machine Base Workbench Figure 16. Disconnecting power. Figure 14. "Direct Mount" setup. -16- Model T30945 (Mfd. Since 12/19)

  • Page 19: Lifting & Moving

    Lifting & Moving Test Run The Model T30945 is light enough for one person Once assembly is complete, test run the machine to lift and move a short distance. to ensure it is properly connected to power and safety components are functioning correctly.

  • Page 20: Section 4: Operations

    Places tile on table firmly against fence or ects. Regardless of the content in this sec- miter guide, or uses some other guiding fix- tion, Grizzly Industrial will not be held liable ture to guide tile while using bevel table. for accidents caused by lack of training.

  • Page 21: Disabling & Locking Switch

    Rinse tank, re-install drain plug, and replace is properly disabled. with fresh water before connecting to power and resuming operations. Figure 19. Maximum lock shaft requirements. -19- Model T30945 (Mfd. Since 12/19)

  • Page 22: Making Rip Cuts

    (see Figure 23). Miter Guide Lock Knob Splash Hood Lock Knob Figure 21. Splash hood lock knob location. Figure 23. Miter guide lock knob location. -20- Model T30945 (Mfd. Since 12/19)

  • Page 23: Making Bevel Cuts

    Tilt bevel table up and adjust insert table legs Lock Knob to desired angle stop (see Figure 27). Figure 25. Splash hood lock knob location. Connect machine to power and turn ON. Table Legs Figure 27. Bevel table set to 45˚. -21- Model T30945 (Mfd. Since 12/19)

  • Page 24: Making L-Cuts

    (see Figure 31). If rip cut- ting, remove miter guide. Top View Front View Figure 29. Tile ready for bevel cut. Miter Guide Lock Knob Figure 31. Miter guide lock knob location. -22- Model T30945 (Mfd. Since 12/19)
  • Page 25 Connect machine to power and turn ON. Cut-Off Piece Tile Top view Figure 35. Second cut complete. 13. Without removing tile, turn saw OFF. 14. Wait for blade to stop spinning, then remove tile. -23- Model T30945 (Mfd. Since 12/19)

  • Page 26: Removing & Installing Blade

    (see Figure 37). Installing Blade Open-End Wrench The Model T30945 uses abrasive continuous-rim blades. This type of blade does not cut and wear like typical "toothed" blades, instead they cut and grind simultaneously, making them perfect for ceramics.

  • Page 27: Section 5: Accessories

    Measures 3' wide x 5' long x ⁄ " thick. To reduce this risk, only install accessories recommended for this machine by Grizzly. NOTICE Refer to our website or latest catalog for additional recommended accessories. G5726—4-Pc. Combination Square 12"...
  • Page 28 T20451—“Kirova” Clear Safety Glasses T20452—“Kirova” Anti-Reflective S. Glasses T20456—DAKURA Safety Glasses T20502 T20503 T20452 T20456 T20451 Figure 43. Assortment of basic eye protection. Figure 45. Optional stand for Model T30945. www.grizzly.com 1-800-523-4777 order online at or call -26- Model T30945 (Mfd. Since 12/19)

  • Page 29: Section 6: Maintenance

    Cleaning the Model T30945 is relatively easy. maintenance, or service. Wipe off tile dust with a wet cloth. If dust has built up in the bath or splash hood, use a mild soap and warm water to remove it.

  • Page 30: Section 7: Service

    3. Incorrectly mounted to workbench or stand 3. Adjust feet, shim, or tighten mounting hardware. feet not adjusted properly. 4. Motor bearings at fault. 4. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -28- Model T30945 (Mfd. Since 12/19)
  • Page 31 3. Clean and wax rail. Tile moves 1. Improper feeding technique. 1. Learn/use proper feeding technique. away from 2. Fence not parallel with blade. 2. Adjust fence parallel with blade (Page 30). fence when ripping. -29- Model T30945 (Mfd. Since 12/19)

  • Page 32: Squaring Fence To Blade

    Loosen splash hood lock knob, lift hood fully, and tighten lock knob to secure (see Figure 46). Splash Hood Lock Knob Figure 48. Splash hood mounting screw locations. Figure 46. Splash hood lifted for fence adjustment. Remove miter guide. -30- Model T30945 (Mfd. Since 12/19)

  • Page 33: Adjusting Fence

    Remove miter guide from rip fence and unlock and remove rip fence from table. Figure 51. Rip fence adjustment set screws. Test adjustment by unlocking rip fence and sliding it along table width. Adjust set screws until satisfied. -31- Model T30945 (Mfd. Since 12/19)

  • Page 34: Section 8: Wiring

    Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -32- Model T30945 (Mfd. Since 12/19)

  • Page 35: Wiring Diagram

    Run Capacitor 35MFD 250VAC WARNING! 120 VAC SHOCK HAZARD! 5-15 Plug Disconnect power Ground before working on wiring. Bottom Switch Figure 52. ON/OFF switch. Figure 53. Run capacitor. READ ELECTRICAL SAFETY -33- Model T30945 (Mfd. Since 12/19) ON PAGE 32!

  • Page 36: Section 9: Parts

    SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 70 71 104-1 104-2 104-3 BUY PARTS ONLINE AT GRIZZLY.COM!
  • Page 37 MOTOR FAN PT30945047 FOOT COVER (RR-LH) 104-2 PT30945104-2 BALL BEARING 6201-2RS (FRONT) PT30945048 FOOT (LH) 104-3 PT30945104-3 BALL BEARING 6003-2RS (BACK) BUY PARTS ONLINE AT GRIZZLY.COM! -35- Model T30945 (Mfd. Since 12/19) Scan QR code to visit our Parts Store.

  • Page 38: Labels & Cosmetics

    Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -36- Model T30945 (Mfd.

  • Page 39: Warranty & Returns

    WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.

Table of Contents