Table of Contents
Advertisement
Quick Links
**********************************
invalid calibration data in EEPROM
**********************************
Loading values for devNum [0] from eep file ar5006xs_mb62ag.eep
Operating in 11a at channel 5.220GHz
Devlib Revision 5.2 BUILD #58 Mainline
Devices detected:
PCI deviceID : 0xff16
MAC revisionID: 0xa5
RF productID : 0x6
Using defaults from //depot/sw/branches/ART_525/bringup/ar5k/config/eagle2_0.cfg#1
Base Addr: 0xFFEE0000 Interrupt: 17
Wireless MAC ADDR: 0xFFFF_FFFF_FFFF
Reading in Calibration Setup from calsetup.txt
Reading in Target Powers and CTL Info from calTrgtPwr_ar5006xs_mb62ag.txt
=======================================
Plug in DUT (Device Under Test)
Press any key to start or <ESC> to quit
=======================================
=======================================
Waiting for other test set to finish
=======================================
Setting up Power Meter
Setting up Spectrum Analyzer
Setting up Attenuator
using cal fixed gain for mode 11a from calsetup.txt ... FG6
using cal fixed gain for mode 11b from calsetup.txt ... FG6
using cal fixed gain for mode 11g from calsetup.txt ... FG6
Manufacturing Test start ...
Collecting raw data for the adapter for mode 11a
ch: 5180 --> max pwr is 22.70 dBm
ch: 5320 --> max pwr is 24.10 dBm
ch: 5600 --> max pwr is 22.37 dBm
ch: 5745 --> max pwr is 21.17 dBm
ch: 5825 --> max pwr is 20.01 dBm
Collecting raw data for the adapter for mode 11g
=============================================
|
UNKNOWN BOARD
=============================================
Sub systemID : 0xffff
BB revisionID: 0x61
RF revisionID: 0x3
WLM54AG_1B.log
Page 1
|
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Compex WLM54AG
Summary of Contents for Compex WLM54AG
- Page 1 ********************************** invalid calibration data in EEPROM ********************************** Loading values for devNum [0] from eep file ar5006xs_mb62ag.eep Operating in 11a at channel 5.220GHz ============================================= ============================================= Devlib Revision 5.2 BUILD #58 Mainline Devices detected: PCI deviceID : 0xff16 MAC revisionID: 0xa5 RF productID : 0x6 Using defaults from //depot/sw/branches/ART_525/bringup/ar5k/config/eagle2_0.cfg#1 Base Addr: 0xFFEE0000 Interrupt: 17 Wireless MAC ADDR: 0xFFFF_FFFF_FFFF...
- Page 2 ch: 2412 --> max pwr is 23.35 dBm ch: 2442 --> max pwr is 23.29 dBm ch: 2472 --> max pwr is 22.44 dBm Collecting raw data for the adapter for mode 11b ch: 2412 --> max pwr is 24.18 dBm ch: 2442 -->...
- Page 3 2442 20.1/20.0 19.7/20.0 2472 19.9/20.0 20.0/20.0 Start Spectral Mask Test for mode 11b spec mask - chan:2412 No. Bad Points: 0 spec mask - chan:2442 No. Bad Points: 0 spec mask - chan:2472 No. Bad Points: 0 Start TX EVM Test in 11b mode 2412 MHz 11 Mbps EVM:...
- Page 4 ########################################################################### ============================================== Test complete. Replace DUT (Device Under Test) Press any key to start or <ESC> to quit ============================================== ... WMAC function Attached to the Device for instance = 1 Loading values for devNum [0] from eep file ar5006xs_mb62ag.eep ======================================= Waiting for other test set to finish ======================================= Setting up Power Meter...
- Page 5 5600 MHz 54 Mbps EVM: 5745 MHz 54 Mbps EVM: 5825 MHz 54 Mbps EVM: Start RX PER Test in 11a mode 5180 MHz 54 Mbps 5320 MHz 54 Mbps 5600 MHz 54 Mbps 5745 MHz 54 Mbps 5825 MHz 54 Mbps Start Target Power Control Test in 11g mode FREQ...
- Page 6 Timing Report ... time taken for instrument setup time taken for 11a cal = 6.6 time taken for 11g cal = 4.5 time taken for 11b cal = 4.6 time taken for program eeprom time taken for 11a target pwr ctl time taken for 11a PER and RXSEN time taken for 11g target pwr ctl time taken for 11g PER and RXSEN...
Need help?
Do you have a question about the WLM54AG and is the answer not in the manual?
Questions and answers