Seav WiWeather S/F 433 Manual page 10

position yourself on SPEED LED, the LED will start to double flash for the number of times
equal to the wind Safety threshold in the memory (to every double flash of the SPEED LED
corresponds an increase of 5 Km/h), (example: 5 flashes of SPEED LED = 25 Km/h).
Selection of the wind Safety threshold from 5 to 40 Km/h
The sensor is supplied with the wind Safety intervention threshold equal to 25 Km/h
(SPEED OFF LED).
The programming of the wind Safety threshold selection is carried out as follows: with the
SEL key position yourself on SPEED LED and press the SET key to start the programming
procedure: at the same time, the SPEED LED will start to double flash; (every double flash of
the SPEED LED corresponds to an increase of 5 Km/h), once the desired threshold has been
reached, press the SET key; the selected value will be memorised at the same time and the
SPEED LED will remain on (example: 5 double flashes of SPEED LED = 25 Km/h).
It is possible to repeat the operation in case of an incorrect programming.
3) WIND : (Wind Sensor ON/OFF)
Deactivation of the Wind Sensor
The device is supplied with the Wind Sensor enabled (WIND ON LED).
The deactivation of the Wind Sensor can be carried out as follows: with the SEL key
position yourself on the flashing of the WIND LED and press the SET key for an instant: at
the same time, the WIND LED will switch off and the Wind Sensor deactivation will be
complete. It is possible to repeat the operation to activate the Wind Sensor.
4) SUN : (Sun Sensor ON/OFF)
Enabling the Sun Sensor
The device is supplied with the Sun Sensor disabled (SUN OFF LED).
The enabling of the Sun Sensor can be carried out as follows: with the SEL key position
yourself on the flashing of the SUN LED and press the SET key for an instant: at the same
time, the SUN LED will remain on and the Sun Sensor enabling will be complete. It is
possible to repeat the operation to disable the Sun Sensor.
5) RAIN : (Rain Sensor ON/OFF)
Deactivation of the Rain Sensor
The device is supplied with the Rain Sensor enabled (RAIN ON LED).
The deactivation of the Rain Sensor can be carried out as follows: with the SEL key posi-
tion yourself on the flashing of the RAIN LED and press the SET key for an instant: at
the same time, the RAIN LED will switch off and the Rain Sensor deactivation will be
complete. It is possible to repeat the operation to activate the Rain Sensor.
6) TEST: (Test Sensors ON/OFF)
The device is supplied with the Wind - Sun - Rain Test Sensors disabled (TEST OFF LED).
The activation of the Wind - Sun - Rain Test Sensors can be carried out as follows: with the
SEL key position yourself on the flashing of the TEST LED and press the SET key for an instant:
at the same time, the TEST LED will switch on and the activation of the Wind - Sun - Rain Test
Sensors will be complete. It is possible to repeat the operation to disable the Test Sensors.
Anemometer Test:
manually rotate the Anemometer blades and, at the same time, the WIND MONITOR LED
will switch on, signalling the radio sending of the necessary information to the previously
configured coupled control unit (signalled by the flickering of the CODE MONITOR LED),
controlling the ascent for 5 sec.
Sun Sensor Test:
rotate VR1 trimmer as far as possible clockwise (in + position) and, at the same time, the
SUN MONITOR LED will switch on, signalling the radio sending of the necessary informa-
tion to the previously configured coupled control unit (signalled by the flickering of the CODE
MONITOR LED), controlling the descent for 5 sec. Rotate the VR1 trimmer VR1 anti-clock-
wise (in - position) and, at the same time, the SUN MONITOR LED will switch off, signalling
the radio sending of the necessary information to the previously configured coupled control
unit (signalled by the flickering of the CODE MONITOR LED), controlling the ascent for 5 sec.
Rain Sensor Test:
wet the sensitive part of the Rain Sensor and, at the same time, the RAIN MONITOR LED
will switch on, signalling the radio sending of the necessary information to the previously
configured coupled control unit (signalled by the flickering of the CODE MONITOR LED),
controlling the ascent for 5 sec.
Completed the test, ensure to have dried the sensitive part of the rain sensor before using
the control unit in the normal functioning.
SENSORS MONITOR
The control unit presents four "monitor" indicator LED with which it is possible to display
the radio transmission of the information relating to each sensor.
———————————— — LEDS MONITOR ————————————
LED Reference LED Off
CODE MONITOR Info = OFF
WIND MONITOR Info = OFF
SUN MONITOR Info = OFF
RAIN MONITOR Info = OFF
RESET:
In case it is necessary to reset the control unit default factory configuration, press the
SEL and SET keys together so that all indicator LED switch on and off at the same time.
10
LED On
Info = ON
Info = ON
Info = ON
Info = ON
Rev. 3.0 dated 05/09/2016