Advertisement
LOW-S
After delivery, immediately remove the packaging from the product in a manner that preserves the
packaging and maintains the orientation of the product in the packaging; then inspect the product closely to
determine whether it sustained damage during transport. If damage is discovered during the inspection,
immediately record a complete description of the damage on the bill of lading. If the product is
undamaged, discard the packaging.
NOTES:
1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the
product is used is exclusively the responsibility of the owner/end-user.
2) Vestil is not liable for any injury or property damage that occurs as a consequence of failing to apply
either: a) the instructions in this manual; or b) information provided on labels affixed to the product. Neither
is Vestil responsible for any consequential damages sustained as a result of failing to exercise sound
judgment while assembling, installing, using or maintaining this product.
Table of Contents
Product Features................................................................................................................. 2
Hazard Identification: Explanation of Signal Words..................................................................... 2
Safety Guidelines................................................................................................................. 3
FIG. 1: Trolley assembly and bill of materials............................................................................. 4
Installation.......................................................................................................................... 5 - 6
Use Instructions................................................................................................................... 7
Inspections & Maintenance.................................................................................................... 7 - 8
Label Placement Diagram...................................................................................................... 9
Limited Warranty.................................................................................................................. 10
Copyright 2014 Vestil Manufacturing Corp.
rev. 3/24/2014
Vestil Manufacturing Co.
2999 North Wayne Street, P.O. Box 507, Angola, IN 46703
Telephone: (260) 665-7586 -or- Toll Free (800) 348-0868
Fax: (260) 665-1339
www.vestilmfg.com
L
P
ERIES
OW
ROFILE
I
NSTRUCTION
e-mail:
sales@vestil.com
M
C
B
ANUAL
HAIN
LOCKS
M
ANUAL
LOW, manual.doc
1 of 10
Advertisement
Table of Contents
Related Manuals for Vestil LOW Series
Summary of Contents for Vestil LOW Series
-
Page 1: Table Of Contents
2) Vestil is not liable for any injury or property damage that occurs as a consequence of failing to apply either: a) the instructions in this manual; or b) information provided on labels affixed to the product. Neither is Vestil responsible for any consequential damages sustained as a result of failing to exercise sound judgment while assembling, installing, using or maintaining this product. -
Page 2: Product Features
If after reading the manual you do not understand an instruction, ask your supervisor or employer for clarification, because failure to adhere to the directions in this manual might result in serious personal injury. Copyright 2014 Vestil Manufacturing Corp. 2 of 10... -
Page 3: Safety Guidelines
To reduce the likelihood of injury: DO NOT modify the chain block or the trolley in any way UNLESS you first obtain written approval from Vestil. Unauthorized modifications automatically void the Limited Warranty and might make the product unsafe to use. - Page 4 Copper bushing Flat washer Cotter pin Slotted nut Lock washer Right side plate Shaft stopper pin Split pin Suspension shaft Suspension block Block pin Pin retainer Slotted screw Cotter pin Hand chain wheel Copyright 2014 Vestil Manufacturing Corp. 4 of 10...
-
Page 5: Installation
2mm and 1mm washers Cotter pins (2) 7. Mark the center of the suspension block (25); then measure half of the flange width (half of measurement 2) from the center of the block. Copyright 2014 Vestil Manufacturing Corp. 5 of 10... - Page 6 However, total clearance between the edge of the beam flange and the track roller flanges cannot be more than 1/8in. (3mm) or 1/16in. per side. (Shown by white arrows in FIG. 5). Copyright 2014 Vestil Manufacturing Corp. 6 of 10...
-
Page 7: Use Instructions
Individual links should not be bent or twisted. The points of contact between links should not be significantly worn. Load hook: inspect the hook in accordance with ANSI/ASME B30.10; look for twists, cracks, and elongations. Copyright 2014 Vestil Manufacturing Corp. 7 of 10... - Page 8 30°F to 120°F. Apply lubricant to the contact surfaces as frequently as necessary to ensure that all teeth are thoroughly covered. d. Fasteners and pins – Lubricate fasteners and pins, especially threaded surfaces, with appropriate lubricants (e.g. anti-seize compound or thread lubricant). Copyright 2014 Vestil Manufacturing Corp. 8 of 10...
-
Page 9: Label Placement Diagram
3/24/2014 LOW, manual.doc Label placement diagram: The chain block a trolley should be labeled as shown in the diagram below. Contact Vestil to order a replacement hanging tag if the original tag is lost, damaged, or unreadable. Trolley data tag:... -
Page 10: Limited Warranty
(you) for warranty service. Who may request service? Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an authorized distributor AND Vestil has been fully paid.
Need help?
Do you have a question about the LOW Series and is the answer not in the manual?
Questions and answers