SunTech ST4950 Quick Start Manual
  1. Manuals
  2. Brands
  3. SunTech Manuals
  4. GPS
  5. ST4950
  6. Quick start manual

SunTech ST4950 Quick Start Manual

Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

1. Scope:

Focused initial steps to quickly connect the ST4950 to a PC, configure Network Parameter settings using
SyncTrak, and assemble for use. For detailed specifications and programming information please see the
Related Suntech Documentation links below or contact Suntech Support at

2. Related Suntech Documentation:

a.
Suntech ST4950 Documentation
b.
ST4000 Series SIM Card Information
c.
ST4000 Series-LED Activity and Diagnostic Guide
d.
SyncTrak User Manual
e.
Universal Protocol-Asset Tracking

3. Required Resources:

a.
HW: Suntech ST4950, 6 assembly screws, Magkey, USB to Micro-USB cable, Power Cable, Mag-Cradle
b.
HW: SIM card: Activated, Access Point Name (APN) for carrier/network
c.
HW: PH#1 or PH#2 Screwdriver (Torque Driver recommended)
d.
HW: PC Computer: Windows 10 recommended
e. SW: Suntech USB Driver: v1.1032.3 or newer, available
f.
SW: Suntech SyncTrak: v5.0.6.5 or newer,

4. Connect the ST4950 to a PC

a. Remove solar panel lid to access SIM card holder, Micro-USB, battery and solar connectors, see Figure 2.
ST4950 Quick Start Guide
Connect, Configure and Assemble
Figure 1: Suntech ST4950
available
Figure 2: Remove solar panel lid
support@suntechus.com.
at
support@suntechus.com
at
support@suntechus.com
SU-P-021-RevA, 10/29/2020
Page 1 of 6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST4950 and is the answer not in the manual?

Questions and answers

Related Manuals for SunTech ST4950

Summary of Contents for SunTech ST4950

  • Page 1 Figure 1: Suntech ST4950 1. Scope: Focused initial steps to quickly connect the ST4950 to a PC, configure Network Parameter settings using SyncTrak, and assemble for use. For detailed specifications and programming information please see the Related Suntech Documentation links below or contact Suntech Support at support@suntechus.com.
  • Page 2 Figure 3: Install SIM card Figure 4: Ensure the SIM card holder lid is locked in place c. Next, connect the ST4950 cables in the following order, see Figure 5: i. Short 5 wire battery connector with 2-red, 1-white, 2-black wires ii.
  • Page 3 Solar Panel is connected to the PCB. Check the COM port assigned to the ST4950. Open Windows Device Manager and expand Ports (COM &LPT). The ST4950 will connect as “USB Serial Device (COMxx)”, see Figure 8 for an example. Note: Your PC may assign a different COM port value.
  • Page 4 Parameters may prevent the device from connecting with network or server and is not indicative of a failed device. To fully configure the device please see the Related Suntech Documentation at the beginning of this document or contact Suntech Support at support@suntechus.com.
  • Page 5 If no User ID, Password or PIN is required: select None in Authentication(1000). ii. Contact Suntech Support if you require the use of the User ID, Password and PIN fields. e. Server IP(1005): Enter Server IP address (or URL).
  • Page 6 Using a PH#1-PH#2 Screwdriver or torque driver (2.6 +/- 0.2 in-lbs recommended), attach the base to the solar panel lid. d. The ST4950 can be powered On and Off after assembly with the provided MagKey, see Figure 15 for placement. Review Table 1 for LED indications, please see Related Suntech Documentation for details.

Table of Contents