Advertisement
2 2 - - 7 7 I I G G N N I I T T I I O O N N C C O O N N T T R R O O L L L L E E D D D D O O M M E E L L I I G G H H T T S S U U P P E E R R V V I I S S I I O O N N O O N N / / O O F F F F : : If turned on, the system will turn on the dome
light for 60 seconds when the ignition is turned off. The optional dome light supervision feature must be
installed as described in the Wire Connection Guide.
2 2 - - 8 8 D D O O U U B B L L E E P P U U L L S S E E U U N N L L O O C C K K O O N N / / O O F F F F : : Some vehicles require two pulses on a single wire to unlock the doors. When
the double pulse unlock feature is turned on, the BLUE wire will supply two negative pulses instead of a single
pulse. At the same time, the GREEN wire will supply two positive pulses instead of a single pulse. This makes it
possible to directly interface with double pulse vehicles without any extra parts.
2 2 - - 9 9 F F A A C C T T O O R R Y Y A A L L A A R R M M D D I I S S A A R R M M W W I I T T H H C C H H A A N N N N E E L L 2 2 : : In the default setting the factory alarm disarm output will disarm
the factory alarm system any time the button(s) controlling Channel Two is pressed.
2 2 - - 1 1 0 0 C C H H A A N N N N E E L L 4 4 V V A A L L I I D D I I T T Y Y / / L L A A T T C C H H E E D D / / L L A A T T C C H H E E D D R R E E S S E E T T W W I I T T H H I I G G N N I I T T I I O O N N / / 3 3 0 0 S S E E C C O O N N D D T T I I M M E E D D / / 9 9 0 0 S S E E C C O O N N D D T T I I M M E E D D
O O U U T T P P U U T T : : This wire provides a (-) 200mA output whenever the transmitter button(s) controlling Channel 4 is
pressed. This output can be programmed to provide the following types of outputs (see also the Feature Menus
section):
■ V V a a l l i i d d i i t t y y : : Output that will send a signal as long as the transmission is received.
■ L L a a t t c c h h e e d d : : Output that will send a signal when the Channel 4 button(s) is pressed and will continue until the
same button(s) is pressed again.
■ L L a a t t c c h h e e d d , , r r e e s s e e t t w w i i t t h h i i g g n n i i t t i i o o n n : : Similar to the latched output, this type of output turns on the first time the
Channel 4 button(s) is pressed and turns off the next time the same button is pressed. This type of output
additionally stops and resets whenever the ignition is turned on and then off.
■ 3 3 0 0 - - s s e e c c o o n n d d t t i i m m e e d d : : Output that will send a continuous signal for 30 seconds.
■ 9 9 0 0 - - s s e e c c o o n n d d t t i i m m e e d d : : Output that will send a continuous signal for 90 seconds.
2 2 - - 1 1 1 1 C C H H A A N N N N E E L L 5 5 V V A A L L I I D D I I T T Y Y / / L L A A T T C C H H E E D D / / L L A A T T C C H H E E D D R R E E S S E E T T W W I I T T H H I I G G N N I I T T I I O O N N / / 3 3 0 0 S S E E C C O O N N D D T T I I M M E E D D / / 9 9 0 0 S S E E C C O O N N D D T T I I M M E E D D
O O U U T T P P U U T T : : Channel Four can be programmed for these output configurations. The unit is set to the default valid-
ity output. To change the configuration, use the two-chirp setting to toggle through the different configurations.
Refer to channel 4 feature 2-10 for additional detail.
3 3 4 4
Advertisement
