Download Print this page
Danfoss Optyma Plus OP-LPQM Manual

Danfoss Optyma Plus OP-LPQM Manual

Hide thumbs Also See for Optyma Plus OP-LPQM:

Advertisement

Quick Links

Optyma
Plus
OP-LPQM, OP-MPXM
Name plate
OP-MPXM034MLP00G
A
114X4261
B
C
Application
MBP
D
Refrigerant
(1) R404A R507 R448A/R449A
R407A/R407F/R452A
E
M.W.P. HP
(1) 28 bar
M.W.P. LP
(1) 7 bar
F
Voltage
230 V ~ 1N ~ 50Hz
LRA
60 A
OIL INSIDE
POE 46
G
Serial No.
123456CG2816
xxxxxxxxxxxxxx
EAN No.
A: Model
B: Code number
C: Application, Protection
D: Refrigerant
E: Housing Service Pressure (Maximum
working pressure)
F: Supply voltage, Locked Rotor Ampere,
Maximum Current Consumption
G: Serial Number and bar code
Picture 2 : Stacked mounting
Picture 4 : Normal wiring
© Danfoss | DCS (CC) | 2020.12
MADE IN INDIA
Y
IP 54
(2) R134a
R513A
(2) 23 bar
(2) 5 bar
MCC 19 A
Picture 1 : Minimum mounting distances
Q: Air in
Danfoss A/S, 6430 Nordborg, Denmark
Unit
Housing 4
(Code n° 114X34-- or 114X44--)
V
U
V
T: Mounting brackets for stacked mounting (not supplied)
U: M8 bolts for stacked mounting (supplied)
V: Mounting bolts (not supplied)

Q
W
Z
R
X
R: Air out
W
X
Y
Z
[mm]
[mm]
[mm]
[mm]
250 900 700 700
T
U
Picture 5 : Temporary wiring
The condensing unit must only be used for
its designed purpose(s) and within its scope of
application.
Under all circumstances, the EN378 (or
other applicable local safety regulation)
requirements must be fulfilled.
The condensing unit is delivered under nitro-
gen gas pressure (1 bar) and hence it cannot
be connected as it is; refer to the «installation»
section for further details.
The condensing unit must be handled with cau-
tion in the vertical position (maximum offset
from the vertical : 15°)
Installation and servicing of the condensing
units by qualified personnel only.
Follow these instructions and sound
refrigeration engineering practice relating to
installation, commissioning, maintenance and
service.
Picture 3 : Electronic controller display
Compressor running
Crankcase heater on
Fan running
Temperature value for suction pressure.
Push lower button to switch to tempera-
ture value for condensing pressure
118A2221A - AN363632996019en-ZA0101 | 1

Advertisement

loading

Summary of Contents for Danfoss Optyma Plus OP-LPQM

  • Page 1 U: M8 bolts for stacked mounting (supplied) ture value for condensing pressure V: Mounting bolts (not supplied) Picture 2 : Stacked mounting Picture 4 : Normal wiring Picture 5 : Temporary wiring  © Danfoss | DCS (CC) | 2020.12 118A2221A - AN363632996019en-ZA0101 | 1...
  • Page 2: Version Control

    Use • The unit ambient temperature may not exceed appropriate and safe lifting equipment.. 50°C during off-cycle. • When stacking, the topmost unit must be 2 | AN363632996019en-ZA0101 - 118A2221A © Danfoss | DCS (CC) | 2020.12...
  • Page 3 33 bar setting. to the compressor while it is under vacuum as 40 = R448A, 41 = R449A, 42 = R452A. • Once pressure relief valve opens, Danfoss this may cause internal damage. • Push the middle button to confirm the selected recommended to replace new pressure relief value.
  • Page 4 • Condensing unit measurements are made • When needed, additional refrigerant in liquid according standard “EN 13771-2:2017” 4 | AN363632996019en-ZA0101 - 118A2221A © Danfoss | DCS (CC) | 2020.12...
  • Page 5 The product warranty may be void in following • Any deviation from recommended instructions units and oil should be recycled by a cases: pertaining to installation, application or suitable company at its site. © Danfoss | DCS (CC) | 2020.12 118A2221A - AN363632996019en-ZA0101 | 5...
  • Page 6 H Nameplate A Ø12 Hole for Mounting Air out Electrical Cables B Sight Glass Suction Port Note: all dimension are in mm C Controller Display G Liquid Port 6 | AN363632996019en-ZA0101 - 118A2221A © Danfoss | DCS (CC) | 2020.12...
  • Page 7 5 Filter Drier B4 Low Pressure cartridge Switch (auto-reset) (PSL) Insulation 6 Sight Glass D1 Pressure relief valve (PRV) 7 Liquid Ball Valve R1 Ambient Temperature sensor (T4) © Danfoss | DCS (CC) | 2020.12 118A2221A - AN363632996019en-ZA0101 | 7...
  • Page 8 Denmark Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trade- marks in this material are property of the respective companies.

This manual is also suitable for:

Optyma plus op-mpxm