Girard Systems 98GC661B Installation Manual

Girard Systems 98GC661B Installation Manual

5 channel wall switch

Advertisement

98GC661B
5 CHANNEL WALL SWITCH
INSTALLATION AND PAIRING GUIDE
RV AWNING PRODUCTS
1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (949) 259-4000 FAX (949)276-5500
www.girardrv.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 98GC661B and is the answer not in the manual?

Questions and answers

Summary of Contents for Girard Systems 98GC661B

  • Page 1 98GC661B 5 CHANNEL WALL SWITCH INSTALLATION AND PAIRING GUIDE RV AWNING PRODUCTS 1361 CALLE AVANZADO, SAN CLEMENTE, CA 92673 (949) 259-4000 FAX (949)276-5500 www.girardrv.com...
  • Page 2 Shore Power – if connected; Generator Power – if the generator is running; Inverter Power – batteries must be charged for inverter operation. Girard Systems awnings are supplied with an electric motor appropriate to the product.
  • Page 3: Table Of Contents

    These components must be electronically matched or paired before use. This is usually done at the Girard Systems factory. Should the need arise for the user to pair a device with the motor controller they must...
  • Page 4: Product Description

    PRODUCT DESCRIPTION The 98GC661B is a 5 channel RF transmitter, powered by two 3v Lithium batteries (CR2032) designed to control a single awning by means of a 6 button control pad as seen in the picture below. The faceplate can be removed easily by holding the module at the left and right edges firmly in one hand and push the STOP and P2 buttons with two fingers of your other hand.
  • Page 5: Setting Time And Date

    SETTING TIME AND DATE The 98GC661B not only controls the awning but functions as a 24 hour clock and a 7 day calendar. Screw mounting holes When the battery tray is inserted the display will light up as in the photograph above, then it will default to Mon 10:00.
  • Page 6: Installation

    Screws are provided with the module for this purpose. The 98GC661B has an operating range of 100’ but should be mounted with as few obstructions as possible between itself and the Motor Controller it is paired...
  • Page 7: Programming

    PROGRAMMING The following pages give instructions of how to pair the 98GC661B with various motor controllers. Ensure that you select the correct set of instructions for the motor controller on your vehicle. GC136 AC Motor Controller Program Button Stop Button Fig.1...
  • Page 8: Gc274A / Gc274B Ac Motor Controllers

    Lid Release Fig.3 To pair the 98GC661B Wall Switch with a GC274A or GC274B first remove the lid of the motor control module by pressing on the Lid release catches as shown in Fig.3 Note; When carrying out this part of the procedure each step must be executed within 10 seconds of the previous one or the module will revert to factory settings.
  • Page 9: 98Gc74 Ac Motor Controller

    98GC74 AC Motor Controller When pairing with the 98GC74 it is advised that the awning to be controlled is manually extended couple of feet to enable the programmer to see if the awning is responding in the correct direction when the buttons on the wall switch are pressed. The programming window for this module is only 6 seconds so please ensure that the programming instructions are read and understood before attempting to execute them.
  • Page 10: Gc732G Dc Motor Controller

    GC732G DC Motor Controller Program Button Fig.4 To pair the 98GC661B Wall switch with a GC732G Motor controller follow the steps below. Note; When carrying out this part of the procedure each step must be executed within 10 seconds of the previous one or the module will revert to factory settings.
  • Page 11: Gc1146C Dc Motor Controller

    GC1146C DC Motor Controller To pair the 98GC661B Wall switch with a GC1146C Motor controller follow the steps below.  Identify the Remote handset which operates the DC Motor controller for the awning that the wall switch is to operate. This is likely to be either a 98GC1063 Single channel, or a 98GC1029 Multi channel handset.
  • Page 12 Ensure that the awning responds correctly to the wall switch by pressing the OUT, STOP and IN buttons alternately. For queries or assistance with programming any remote handset to any of your G-Link devices please call Girard Systems toll free on 800–382–8442 between 7:30am and 5:00pm P.S.T.

Table of Contents

Save PDF