NEC MultiSync P435 User Manual page 102

SLOT MENU
COMPUTE MODULE*
POWER CONTROL
POWER SUPPLY
POWER BUTTON
RESET
Connection Status*
3
Power Status*
3
Module*
3
POWER SETTING
AUTO POWER UP
AUTO SHUTDOWN*
POWER SUPPLY
OFF DELAY
AUTO DISPLAY OFF
OFF WARNING
ADVANCED SETTING
SHUTDOWN SIGNAL
IR SIGNAL
MONITOR CONTROL
WDT
START UP TIME
PERIOD TIME
SLOT POWER
RESET
*: This input is available when the optional Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute Module are installed. See
* 2 : This function depends on which Option Board you are using. This function is only available when an Option Board is installed.
* 3 : Some Option Boards may not show it correctly.
* 4 : When the option board is a computer, check the settings on the computer side.
Configure settings for a Raspberry Pi Compute Module Interface Board and Raspberry Pi Compute
Module.
Controls power to the Compute Module.
Select [YES] then press SET on the remote control to power on the device.
Select [NO] then press SET on the remote control to power off the device.


NOTE: The option that is highlighted under [POWER SUPPLY] when you open the [POWER CONTROL]
menu indicates the current power status. If [YES] is highlighted, the power is on. If [NO] is
highlighted, the power is off.
Performs a normal shut down of the Compute Module.
Press SET to force a shutdown and restart of the Compute Module when it does not respond to shutdown
using the [POWER BUTTON] function.


NOTE: This function may corrupt the data files on the Compute Module and data files on a storage
device connected to the Compute Module interface card.
Shows the connection status of a Compute Module. If the status is not "Connected" then a device is not
installed.
Shows the operating status of the Compute Module.
Shows information about the Compute Module Interface Board.
The Compute Module will be turned on automatically when the monitor power is turned on.
The Compute Module is turned off when the monitor switches into standby mode.
4
This sets the time delay after the Shutdown Signal is set until the power to the Compute Module is
turned off. Configure this to allow adequate time for any software to shutdown safely.
Allows the monitor switch into the same status when the Compute Module goes into standby or power
save mode.


NOTE: If you select [ENABLE], the monitor power is not automatically on when the Compute Module
turns on.
Shows a warning, when shutting down the power to the Compute Module, that the device should be turned
off from within the OS of the device. This message cannot be changed.
This function is available when [POWER SUPPLY] is [OFF].
Enables or disables the use of GPIO 23 to signal that power to the Compute Module will be shutting down.
Enables or disables the forwarding of IR remote control signals.
Enables or disables the internal serial connection between the monitor and the Compute Module.
Enables or disables the monitor's built-in Watchdog Timer function for the Compute Module.
When enabled, the monitor will expect to receive a periodic reset command from the Compute Module via
the internal UART. If the command isn't received for three consecutive timeout periods, the monitor will
restart the Compute Module.
Sets the time delay for when the monitor should start receiving WDT reset commands after the Compute
Module powers up.
Sets the maximum amount of time within which the monitor must receive WDT reset commands from the
Compute Module.
Allows the monitor to supply power to an Option Board slot during power save mode or standby mode.
[AUTO]: Power is continuously supplied to the Option Board slot, even during power save and standby
modes.
Power to the Option Board slot stops during power save and standby modes, when there is no installed
device.
[ON]: Power is continuously supplied to the Option Board slot, even during power save and standby
modes.
[OFF]: Power to the Option Board slot stops during power save and standby modes.


NOTE: To activate the power management function with no signal input from a device connected to the
Option Board, please set [OPTION POWER] to [AUTO] or [ON].
Resets all SLOT settings back to factory settings, except for [POWER SUPPLY] in [OPTION], [POWER
SUPPLY] and [ADVANCED SETTING] in [COMPUTE MODULE].
English−98
page 83.