® Display and Screw Down Crown/Pushbuttons ® LCD Digital Displays ® Setting Time and Date ® Setting Date/Time and Alarm ® Setting Time Zones/Leap Year ® Resetting Chronograph Hands to Zero ® Timing Mode • Simple Chronograph Function ® Timing Mode • Split-Time or Intermediate Times Function ®...
2 & 3 for adjustments only. Pushbuttons do not screw down; Do not operate pushbuttons under water! NOTE - Failure to screw down Crown to resist moisture will void your warranty and Screw Down Crown/Pushbuttons CHASE-DURER GENEVE 330 FEET FIGHTER...
12/24 Hour Time mode indicators Date Note - When the displays are flashing while watch is in setting mode, it indicates the watch is waiting for input. Blinking or partial displays when watch is in normal operating mode (not setting mode) indicates a low battery condition.
“60” to stop the second 330 FEET ALARM and press button once more. After 2 seconds, the two displays will Set crown in position adjust only the hour hand CHASE-DURER GENEVE 1/100 SEC FIGHTER COMMAND DATE Set crown in position...
Note - To test the alarm, press and hold ; the alarm should produce a beeping tone. for 2 seconds and then change to one are displayed in the left LCD, press if digital time is set to standard until the left LCD changes from CHASE-DURER GENEVE 330 FEET 1/100 SEC FIGHTER...
330 FEET ALARM and turn the hour hand counterclockwise (backwards) 24 hours and the right LCD (date) will display the correct date CHASE-DURER GENEVE 1/100 SEC FIGHTER COMMAND...
Resetting Chronograph Hands to Zero The chronograph hands can be set at zero or another time zone. Set the counter at 0 12 hour CHASE-DURER GENEVE 330 FEET 1/100 SEC FIGHTER COMMAND ALARM DATE Note: Pressing PUSHBUTTONS momentarily will advance hands one index mark at a time.
ADD FUNCTION: Order in which pushbuttons should be pressed. START STOP Read Note* Step ) may be repeated as many as necessary; Step before START STOP CHASE-DURER GENEVE 330 FEET 1/100 SEC FIGHTER COMMAND ALARM DATE Reset to Zero after step...
Timing Mode • Split-Time or Intermediate Times Function order of functions CHASE-DURER GENEVE 330 FEET 1/100 SEC FIGHTER COMMAND ALARM DATE CHASE-DURER GENEVE 330 FEET 1/100 SEC FIGHTER COMMAND ALARM DATE RESTART (catching up) Note* Step as necessary; Step START...
Timing Mode • Lap-Time Function order of functions START CHASE-DURER GENEVE Crown set in position 1 330 FEET 1/100 SEC FIGHTER COMMAND ALARM DATE LAP 2 Read TIME 2 0 hour 1 minute 43 seconds 30/100 second RESTART (catching up)
When stopped, the second hand points to the number on the TACHYMETRE scale by which the number of units (1, 10, 100 or 1,000 etc.) must be multiplied to obtain per-hour production rate or per-hour speed. CHASE-DURER GENEVE 330 FEET...
NOTE - The scale is valid for all elapsed times from outside this range, then the answer on the dial is not valid. Some of the following examples show ways to get around this limitation. CHASE-DURER GENEVE 330 FEET 1/100 SEC...
Hold the watch horizontal and point the hour hand at the sun; the bezel’s indicator will be pointing North. If there is any doubt as to which end of the line is north, remember that the sun rises in the east, sets in the west, and is due south at noon.
Deployment buckle with double lock security clasp. ® Screw-locked crown and s ® Water resistant to 100m/330 feet. ® cratch-resistant sapphire crystal. ® iameter - 42mm. ® Serial numbered. ® 2 year limited international warranty. Specifications FIGHTER COMMAND crew-in back...
Need help?
Do you have a question about the Fighter Command and is the answer not in the manual?
Questions and answers