Advertisement
Available languages
Available languages
Table of Contents
H-5598
IGLOO PARTY BAR
TOOLS NEEDED
Wrench
Lid x 1
Rigid
Locking
Caster x 2
Caster x 2
Figure 1
Short
Screws
Long Screws
PAGE 1 OF 9
1-800-295-5510
uline.com
Phillips
Screwdriver
Caster Mounting
Hardware x 16
Opener x 1
INSTALLATION
Mounting
Bracket
Cooler
PARTS
Cooler x 1
Bottle
Short
Screw x 2
1.
Remove two short screws and bottle opener from
bag. Line up the bottle opener with the two most
upper holes. Using the Phillips screwdriver, tighten
the short screws into the cooler. (See Figure 1)
NOTE: The holes are not pre-cut, but are
marked with indentations in the cooler wall.
2. Attach mounting bracket to cooler wall using the two
long screws. Make sure mounting bracket is upright
(See Figure 1)
NOTE: The holes are not pre-cut, but are
marked with indentations in the cooler wall.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Base x 1
Mounting
Long
Bracket x 1
Screw x 2
Cap Catch
Bin x 1
0521 IH-5598
Advertisement
Table of Contents
Related Manuals for U-Line H-5598
Summary of Contents for U-Line H-5598
- Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-5598 1-800-295-5510 uline.com IGLOO PARTY BAR TOOLS NEEDED Wrench Phillips Screwdriver PARTS Base x 1 Lid x 1 Cooler x 1 Rigid Locking Caster Mounting Bottle Short Mounting...
- Page 2 INSTALLATION CONTINUED 3. Slide the cap catch bin onto the mounting bracket. Figure 2 (See Figure 2) 4. Connect the lid by pushing the three pins into the Figure 3 clips located on the cooler. (See Figure 3) 5. Flip the base upside down to install the rigid casters Locking Figure 4 Rigid...
- Page 3 INSTALLATION CONTINUED 10. Unscrew battery cover using the Phillips screwdriver Figure 6 and install four AA batteries (not included). Secure battery cover using the Phillips screwdriver. (See Figure 6) SAFETY • Do not sit on lid or stack heavy objects on lid. Doing •...
-
Page 4: Herramientas Necesarias
H-5598 800-295-5510 uline.mx IGLOO PARTY BAR HERRAMIENTAS NECESARIAS Llave Desarmador de Cruz PARTES 1 Base 1 Tapa 1 Hielera 2 Ruedas 2 Ruedas 16 Accesorios 1 Abrebotellas 2 Tornillos 1 Soporte 2 Tornillos 1 Gaveta para Fijas con Seguro de Instalación... - Page 5 CONTINUACIÓN DE INSTALACIÓN 3. Deslice la gaveta para recolectar tapas en el Diagrama 2 soporte de montaje. (Vea Diagrama 2) 4. Fije la tapa insertando los tres pasadores en los Diagrama 3 clips ubicados en la hielera ejerciendo presión. (Vea Diagrama 3) 5.
- Page 6 CONTINUACIÓN DE INSTALACIÓN 10. Desatornille la cubierta de las baterías usando el Diagrama 6 desarmador de cruz e inserte cuatro baterías AA (no incluidas). Fije la cubierta de las baterías usando el desarmador de cruz. (Vea Diagrama 6) SEGURIDAD • No se siente sobre la tapa ni estibe objetos pesados •...
-
Page 7: Outils Requis
H-5598 1-800-295-5510 uline.ca IGLOO – GLACIÈRE OUTILS REQUIS Clé Tournevis cruciforme PIÈCES Base x 1 Couvercle x 1 Glacière x 1 Roulette Roulette Matériel Décapsuleur x 1 Support de Bac à rigide x 2 verrouillable x 2 d'installation courte x 2 fixation x 1... - Page 8 INSTALLATION SUITE 3. Glissez le bac à capsules sur le support de fixation. Figure 2 (Voir Figure 2) 4. Installez le couvercle en insérant les trois tiges Figure 3 dans les fentes des supports situés sur la glacière. (Voir Figure 3) 5. Retournez la base à l'envers pour installer les Roulettes Figure 4 Roulettes...
- Page 9 INSTALLATION SUITE 10. À l'aide du tournevis cruciforme, dévissez le Figure 6 couvercle du compartiment à piles et installez quatre piles AA (non comprises). Refermez le couvercle du compartiment à piles à l'aide du tournevis cruciforme. (Voir Figure 6) SÉCURITÉ • Ne vous assoyez pas sur le couvercle et n'empilez •...
Need help?
Do you have a question about the H-5598 and is the answer not in the manual?
Questions and answers