Specifications; General Safety - Water Ace R5PILT Owner's Manual

Pedestal sump pump
Table of Contents

Advertisement

Available languages

Available languages

DESCRIPTION
This Pedestal Sump Pump is designed for home sumps. Unit is
equipped with a 3-prong grounding-type power cord. Sleeve
bearings on motor shaft never need lubrication. Automatic
reset thermal protection.
NOTICE: This unit is not designed for applications involving
salt water or brine! Use with salt water or brine will void
warranty.

SPECIFICATIONS

Power supply required .......................................115V, 60 HZ.
Horsepower...................................................................1/2
Motor duty .......................................................Intermittent
Liquid Temp. Range ............................32°F to 70°F(0°-21°C)
Individual Branch Circuit Required
GFCI Class A...........................................................15 Amps
Motor full load (maximum) .....................................7.3 Amps
Discharge: ........................................................1-1/2" FNPT

GENERAL SAFETY

Electrically powered sump pumps normally give many years of
trouble-free service when correctly installed, maintained, and
used. However, unusual circumstances (interruption of power
to the pump, dirt/debris in the sump, flooding that exceeds
the pump's capacity, electrical or mechanical failure in the
pump, etc.) may prevent your pump from functioning normally.
To prevent possible water damage due to flooding, consult
your retailer about a secondary AC sump pump, a DC backup
sump pump, and/or a high water alarm. See the
"Troubleshooting Chart" in this manual for information
about common sump pump problems and remedies. For more
information, see your retailer or call the Consumer Hotline at
1-800-942-3343.
1. Know the pump application, limitations, and potential
hazards.
Do not use in explosive atmospheres.
Pump water only with this pump. Failure to follow this
warning can result in personal injury and/or property
damage.
2. Disconnect power before servicing.
3. Release all pressure within system before servicing any
component.
4. Drain all water from system before servicing.
PERFORMANCE
Model
5' (1.5)
R5PILT
3,830 (14,498)
WA584
5. Secure discharge line before starting pump. An unsecured
6. Check hoses for weak or worn condition before each use,
7. Inspect sump, pump and system components monthly.
8. Provide means of pressure relief for pumps whose discharge
9. Personal Safety:
10. When wiring an electrically driven pump, follow all electri-
11. This equipment is only for use on 115 volt (single phase)
TOTAL LIFT IN FEET (M)
CAPACITY IN GPH (LPH)
10' (3.0)
2,720 (10,296)
2
Risk of flooding. If a flexible discharge
hose is used, pump may move when motor starts. If it
moves far enough so that switch hits side of sump, switch
may stick and prevent pump from starting.Make sure pump
is secured so it cannot move around in sump.
discharge line will whip, possibly causing personal injury
and/or property damage.
making certain all connections are secure.
Keep free of debris and foreign objects. Perform routine
maintenance as required.
FIRE HAZARD - Do not store or rest
objects on or near motor or switch linkage. Keep all
flammable objects or liquids away from motor.
line can be shut-off or obstructed.
a. Wear safety glasses at all times when working with
pumps.
b. Keep work area clean, uncluttered and properly lighted
– replace all unused tools and equipment.
c. Keep visitors at a safe distance from work area.
d. Make workshop child-proof – with padlocks, master
switches, and by removing starter keys.
cal and safety codes, as well as most recent National
Electrical Code (NEC) and Occupational Safety and Health
Act (OSHA).
and is equipped with an approved 3-conductor cord and 3-
prong, grounding-type plug.
To reduce risk of electric shock, be cer-
tain that it is connected to properly grounded, ground-
ing-type receptacle.
Never connect green (or green and yel-
low) wire in cord to a live terminal!
Where a 2-prong wall receptacle is encountered, it must be
replaced with properly grounded 3-prong receptacle
installed in accordance with the National Electrical Code
and local codes and ordinances.
Maximum Lift
15' (4.6)
1610 (6,094)
(No Flow)
in Feet (M)
20' (6.1)

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents