Declarations - ALTA Bliss Automation Programming And Users Manual
15 channel remote control
Hide thumbs
Also See for Bliss Automation:
- Installation and reference manual (9 pages) ,
- Programming and users manual (2 pages)
Table of Contents
Advertisement
Declarations
U.S. RADIO FREQUENCY FCC COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
ISED RSS WARNING:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
2
B L I S S R E M O T E C O N T R O L
|
R E F E R E N C E G U I D E
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Bliss Automation and is the answer not in the manual?
Questions and answers
BLINDS NOT CHARGING
ALTA Bliss Automation blinds may not be charging due to the following reasons:
1. Low Battery Alert – If the battery has run out, it needs to be recharged.
2. Charging Issues – Ensure the battery is connected to the correct USB power source (USB 5V 1A or USB 5V 2A).
3. Blinking Indicators – A blinking red light indicates a low battery, while a blinking green light shows charging is in progress. A solid green light means charging is complete.
4. Environmental Factors – The motor should not be exposed to moisture or extreme temperatures (-10℃ to +50℃).
5. Hardware Issues – If power cables are damaged or incorrectly connected, charging may not work.
Checking these factors can help diagnose and resolve charging issues.
This answer is automatically generated
Reset to factory, did pairing step. Unit is charged. When I press up or down it jogs but does not keep moving. I have been working on this for hours and hours.
If the ALTA Bliss Automation unit jogs but does not keep moving after a factory reset, follow these troubleshooting steps:
1. Check Battery and Power:
- Ensure the battery is not dead or inserted incorrectly (check polarity).
- If using a solar panel, recharge with the provided charger and check panel positioning.
- Verify that the motor is properly connected to power.
2. Check for Radio Interference:
- Keep the remote control and motor antenna away from metal objects.
- Move the remote closer to the receiver.
3. Check Remote Pairing:
- After a factory reset, the motor must be re-paired with the remote.
- Press the P1 button on the motor for about 2 seconds until the motor jogs once and beeps once.
- Within 10 seconds, press and hold the “Stop” button on the remote until the motor jogs twice and beeps three times.
4. Sleep Mode or Multiple Motors:
- Ensure other motors are in sleep mode to avoid interference.
- Make sure only one motor is paired to the remote channel being used.
5. Check Wiring:
- Confirm wiring is connected correctly if applicable.
If the motor jogs but does not continue operation, it is likely not fully paired with the remote or affected by one of the above issues. Re-pairing and checking power and signal conditions should resolve the issue.
This answer is automatically generated
Shade will not move either direction - new remote battery and unit charged fully
The ALTA Bliss Automation shade may not move in either direction despite a new remote battery and a fully charged unit because the motor direction cannot be changed if the upper and lower limits are already set. In this case, direction change can only be done using the P1 button. If the motor is set to move in a direction that is blocked by the preset limits, it will not respond to remote commands.
This answer is automatically generated
We moved into place with 2 shades that are synced with remote. They worked fine- today only 1 responds.