ALTA BLISS Automation Programming And Users Manual

DECLARATIONS
U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development
Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation of the device. Le présent appareil est conforme aux CNR d'ISED
applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
FCC SAR Warning:
RF Exposure Information (SAR): The SAR limit of USA (FCC)is 1.6W/Kg averaged
over one gram of tissue.
Product Type: BLISS Bridge (FCC ID: 2AU29-BLISSRFWIFIHUB) has also been
tested against this SAR limit. The device was tested for typical body-worn
operations to keep the BLISS Bridge at least 20cm from the body. When worn on
body must be correct back clip for this product, use of non-approved accessories
may result in exposure levels which exceed the uncontrolled environmental RF
exposure limits.
FCC SAR Warning:
The SAR limit of IC is 1.6W/Kg averaged over one gram of tissue.
Product Type: BLISS Bridge, model number: BLISS Bridge Wifi and RF (IC:
25624-BLISSWIFIHUB) has also been tested against this SAR limit. The device was
tested for typical body-worn operations to keep the BLISS Bridge at least 20cm
from the body. When worn on body must be correct back clip for this product,
use of non-approved accessories may result in exposure levels which exceed the
uncontrolled environmental RF exposure limits.
Le SAR de IC est limité à 16w / kg, avec une moyenne par gramme. Produits
Type: BLISS Bridge, type: BLISS Bridge Wifi and RF (IC: 25624-BLISSWIFIHUB) a
également été testé pour la limite SAR. Ce dispositif est utilisé pour tester des
opérations d 'usure corporelle typiques et des opérations en direction du Haut de
physique, de manière à maintenir une distance d' au moins 20cm entre le BLISS
Bridge et le visage. Osure.`
Product
Certification
BLISS Automation
™
AMP USB Bridge allows the user to link their motorized Shades, Blinds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
interaction with other IoT products.
Step 1 Download APP
Please scan the QR code below.
SERIAL BRIDGE
PROGRAMMING
AND USERS GUIDE
Step 2
Quick Start Guide for
Please scan the QR code below to learn more about linking the AMP USB Bridge
AMP USB Bridge
with your home Wi-Fi router, setting up the AMP APP, and establishing a connection
with other IoT applications.
Product
Certification
BLISS Bridge allows the user to link their motorized Shades and Blinds into a Wi-Fi
network enabling control via smart APP and interaction with other IoT products and
Third Party Integration.
AMP USB Bridge allows the user to link their motorized Shades, Blinds,
and Draperies into a Wi-Fi network, enabling control via smart APP and
Please scan the QR code below.
STEP 1
Please scan the QR Code below to download the app.
by Alta
Quick Start Guide for
AMP USB Bridge
Product
Certification
AMP USB Bridge allows the user to link their motorized Shades, Bli
and Draperies into a Wi-Fi network, enabling control via smart APP
interaction with other IoT products.
Step 1 Download APP
Please scan the QR code below.
Step 2
Please scan the QR code below to learn more ab
with your home Wi-Fi router, setting up the AMP
with other IoT applications.
Step 2
STEP 2
Please scan the QR code below to learn more about linking the AMP USB
with your home Wi-Fi router, setting up the AMP APP, and establishing a Please scan the QR Code below to view more about setting up the BLISS APP
along with additional BLISS Automation troubleshooting and how to videos.
with other IoT applications.