Advertisement
Quick Links
Operation Manual
5 in 1 Multifunction Petrol Tool
Grass Trimmer/Hedge Trimmer/Pole Mounted Pru-
ner/Brush Cutter
61494
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61494
Summary of Contents for WilTec 61494
- Page 1 Operation Manual 5 in 1 Multifunction Petrol Tool Grass Trimmer/Hedge Trimmer/Pole Mounted Pru- ner/Brush Cutter 61494 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Starting the engine will cause sparks. Sparks can ignite flam- mable substances nearby. Motors emit carbon monoxide, an odourless, colourless poison gas. Inhaling carbon monoxide can cause nausea, fainting, or even death. © by WilTec Wildanger Technik GmbH Item 61494 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 Everyone wanting to use, repair or maintain the product must have read and understood the content of this manual. Keep it in a safe place and ensure that they are handed out with the device when you © by WilTec Wildanger Technik GmbH Item 61494 Page 4 http://www.WilTec.de...
- Page 5 Only set up the device on stable and level surfaces from which it cannot fall. Make sure that both muffler and air filter are working properly as these parts act as flame re- © by WilTec Wildanger Technik GmbH Item 61494 Page 5 http://www.WilTec.de http://www.aoyue.eu...
- Page 6 4. Only carry the device by the handles. Place it in the vehicle so that it cannot tip over and the blades cannot injure anyone. With the device tipping over, fuel could leak or people near the device could be injured. © by WilTec Wildanger Technik GmbH Item 61494 Page 6 http://www.WilTec.de...
- Page 7 Wear suitable protective clothing. Slips, trips or falls: Falls can lead to very serious injuries. Wear non-slip shoes, make sure you • stand securely and always stay alert and focused. © by WilTec Wildanger Technik GmbH Item 61494 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 Air filter 14 S4 Allen key (4 mm) Start handle 15 Open-end wrench Fuel tank 16 Screwdriver Throttle trigger 17 Measuring beaker for fuel mixture Shoulder harness © by WilTec Wildanger Technik GmbH Item 61494 Page 8 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 9 Oil tank Cutting cover Chain Hedge trimmer Figures 4 and 5 № Name № Name Lock hole Cutting unit 180° cutting unit adjusting lever Cutting cover Lever lock © by WilTec Wildanger Technik GmbH Item 61494 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 10 6500 Fuel tank capacity (ℓ) Ignition Capacitor discharging ignition (CDI) Mixing ratio 1:25 (oil:petrol) Weight (㎏) 12.5 Brush cutter Size (㎜) 255×1.4×25.4 Trimmer Cutting width (㎜) © by WilTec Wildanger Technik GmbH Item 61494 Page 10 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 11 1. First loosen the blade nut (1) Fig. 2-point 4 using the open-end wrench in- cluded in the scope of delivery and remove the cover. 2. Dispose the chain and guide bar. © by WilTec Wildanger Technik GmbH Item 61494 Page 11 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 12 4 screws and nuts). 2. Fasten the guard using the 4 screws and nuts. Use the included S5 hexagon wrench (5) and the open-end wrench. © by WilTec Wildanger Technik GmbH Item 61494 Page 12 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 13 4 screws and nuts). 2. Fasten the guard using the 4 screws and nuts. Use the S5 hexagon wrench (5) and the open-end wrench included in the scope of delivery. © by WilTec Wildanger Technik GmbH Item 61494 Page 13 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 14 3. Replace the metal cover (3) tighten locking screw (1). Removing the extension: 1. Loosen the locking screw (1). 2. Press the metal clip (2) down and pull out the extension. © by WilTec Wildanger Technik GmbH Item 61494 Page 14 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 15 We recommend using the supplied measuring beaker for the fuel mixture. This will help you to achieve an optimal mixing ratio. Proceed as follows: 1. First pour fuel into the container until it reaches the “578.92” mark. © by WilTec Wildanger Technik GmbH Item 61494 Page 15 http://www.WilTec.de http://www.aoyue.eu...
- Page 16 Then put the carburettor lever to the start position to engage the throttle. Next, press the injection button 6 times to ensure that there is sufficient petrol in the petrol lines. © by WilTec Wildanger Technik GmbH Item 61494 Page 16 http://www.WilTec.de http://www.aoyue.eu...
- Page 17 In addition, an insufficiently tensioned chain wears out faster. © by WilTec Wildanger Technik GmbH Item 61494 Page 17 http://www.WilTec.de...
- Page 18 Never touch a hard surface with the mower head, such as an asphalt, stone or hard clay floor, as this can damage the string coil head beyond repair. Be aware that the severed length of string © by WilTec Wildanger Technik GmbH Item 61494 Page 18 http://www.WilTec.de...
- Page 19 The coil divider should still be visible even with the string fully rolled up. © by WilTec Wildanger Technik GmbH Item 61494 Page 19 http://www.WilTec.de http://www.aoyue.eu...
- Page 20 Cleaning the air filter; exchange, if necessary Checking that all nuts and bolts are tightened Ensuring that the device is not leaking oil or fuel Checking that the starter and the starter rope are intact © by WilTec Wildanger Technik GmbH Item 61494 Page 20 http://www.WilTec.de http://www.aoyue.eu...
- Page 21 (1) With the device operated in dusty area, this type of maintenance should be done more often. (2) This type of maintenance should only be carried out by qualified persons. © by WilTec Wildanger Technik GmbH Item 61494 Page 21 http://www.WilTec.de...
- Page 22 1. Remove the plastic cover. 2. Pull off the spark plug cover and loosen the connector using the socket wrench. 3. If necessary, clean, replace, or readjust the spark plug. © by WilTec Wildanger Technik GmbH Item 61494 Page 22 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
-
Page 23: Troubleshooting
Replace. properly. residues in the fuel Blocked fuel vent Clean or replace. Dirty or worn spark plug Fair wear or tear Clean, adjust or re- place. © by WilTec Wildanger Technik GmbH Item 61494 Page 23 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de... - Page 24 Important notice: The reprint or reproduction, even of excerpts, and any commercial use, even in part of this instructions manual require the written permission of WilTec Wildanger Technik GmbH. © by WilTec Wildanger Technik GmbH Item 61494 Page 24 http://www.WilTec.de...