Advertisement
Quick Links
Advertisement
Related Manuals for Malouf POWER-FLEX 3
Summary of Contents for Malouf POWER-FLEX 3
- Page 1 POWER-FLEX POWER-FLEX OWNER’S MANUAL...
- Page 2 Do not use with oxygen or other flammable gasses. • Carefully read and follow the set up and installation instructions included with the ELECTRICAL • Power-Flex 3 • This product is for use on a standard • Always use a electrical surge protection device with this...
- Page 3 (2) this device must accept any interference received, including interference that may cause undesired operation. • Power-Flex 3 conti • To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirement and void user’s right...
- Page 4 POWER-FLEX OWNER’S MANUAL CONTENTS Overview Assembly Remote Control Massage Electrical Components and Backup Battery Synchronizing Two Bases Test All Functions / Additional Help Warranty Information...
- Page 5 Back Massage Underbed OVERVIEW LED Light Control Box USB Ports Foot Massage Underbed LED Light Power-Flex 3 Retainer Bar Power Supply Box Wireless Remote Control ( ) -Inch Legs ( ) -Inch Legs Power Cord (6) End Caps Sync Cable...
- Page 6 POWER-FLEX OWNER’S MANUAL ASSEMBLY A minimum of two people are required to assemble this adjustable Open box on the floor in the flat bottom facing to avoid Place the box in the room the bed will be used with the bottom of the box facing Carefully remove the binding straps and packaging taking care not to puncture the box with any sharp...
- Page 7 POWER-FLEX OWNER’S MANUAL Middle Leg on King Size Only Head ASSEMBLY Hand tighten all six legs for King into the bed frame until Note that there are two location options for each an outside placement or an inside Tighten the legs in the location of your maintaining a consistent inside or outside location Take care not to over tighten...
- Page 8 POWER-FLEX OWNER’S MANUAL ASSEMBLY With two to four the bed by the metal frame and turn it over so the mattress side is facing up Take caution not to the bed with the or to use the legs as pivot points causing angled pressure as this may cause Move the bed to the desired...
- Page 9 POWER-FLEX OWNER’S MANUAL ASSEMBLY To install the mattress retainer insert one end of the retainer bar in its respective slot until it slides fully into place Flex retainer bar to insert the other end on the other Plug the power cord into the wall outlet and run the test on pages of this You may want to familiarize yourself with the remote control functions prior to running the...
- Page 10 POWER-FLEX OWNER’S MANUAL Programmable Position Preset Zero Gravity Position Preset Anti Snore Position Preset Lounge Position Preset TV/Read Position REMOTE Remote Lock/Unlock Overview CONTROL All of the functions of the bed can be operated with the remote The remote control comes with buttons that will automatically adjust when Head Up/Down Foot Up/Down...
- Page 11 POWER-FLEX OWNER’S MANUAL REMOTE Overview CONTROL The original remote that comes in the box is already paired to the No further PAIRING action is In the event that the remote is not paired with the begin by checking the Ensure the remote batteries are Replace if Ensure the power cord is plugged into a powered The blue pairing button can also be...
- Page 12 POWER-FLEX OWNER’S MANUAL Press and hold to lock or unlock REMOTE CONTROL The remote control can be locked to prevent movement of the When the remote control is no buttons will function and the Lock button will illuminate red when a button is Press and hold the Lock button for or until the button stops flashing...
- Page 13 POWER-FLEX OWNER’S MANUAL MASSAGE To activate the massage press the desired Back or Foot button To adjust the intensity of the massage press the Back or Foot button There are three levels With the massage function in press the Timer button to select a minute The light below will illuminate indicating which timer setting is Timer Setting &...
- Page 14 POWER-FLEX OWNER’S MANUAL ELECTRICAL COMPONENT SETUP Overview The electronic components are and no assembly is some setting and input locations are important for proper setup Foot Motor Input Underbed Light Input and functionality Head Motor Input Massage USB Input...
- Page 15 POWER-FLEX OWNER’S MANUAL ELECTRICAL COMPONENT SETUP USB ports are located under the head portion of the bed base at two locations To access the USB press the Head Up button to raise the bed and reveal the USB Once your device is plugged into the USB you may lower or adjust the bed to your...
- Page 16 POWER-FLEX OWNER’S MANUAL BACKUP Overview BATTERY Use two batteries only If a power outage install the batteries into the power supply to allow temporary power to the base Unplug the power cord from the outlet and remove the cover from the compartment on the underside of the power supply Place two batteries...
- Page 17 POWER-FLEX OWNER’S MANUAL SYNCHRONIZING press the blue Pairing button on the power bases and remove the batteries cord for Base You should hear two from each five reconnect Base A and Base B to the power source and return (for Twin XL and the batteries to Remote A and Ensure Remote A moves both bases by Split sizes only)
- Page 18 POWER-FLEX OWNER’S MANUAL SYNCHRONIZING (for Twin XL and Split sizes only) Place two Twin XL or split size adjustable bases next to each other in desired Plug in Sync Cable to the control box of each base into the “Program” input on the control box With the connecting cable use remote and test all functions of the bed...
- Page 19 POWER-FLEX OWNER’S MANUAL TEST ALL Zero Gravity Preset Head/Foot Up FUNCTIONS Anti Snore Preset Head/Foot Down TV/Read Preset Foot Up Lounge Preset Foot Down Memory Back Massage/Intensity Remote Lock Foot Massage/Intensity Head Up Timer Head Down Massage Off/Last Overview Flat Massage Type Underbed LED Lights To ensure proper...
- Page 20 POWER-FLEX OWNER’S MANUAL NOTES: ADDITIONAL HELP Check under the bed base to verify the wired connections are secure and there are no cords or bedding obstructing the movement of the If the remote control activates the wrong the motors are plugged into the wrong input on the control Switch the input location of the cords on the control Ensure remote lock has been deactivated...
- Page 21 fitness for a particular purpose and all other warranties otherwise arising by operation of law, course of dealing, custom, trade, or otherwise. Malouf® shall not be liable for any consequential damages or losses arising from the purchase, installation and/or use of this product.