Specifications; Warranty Conditions - PIEPS iprobe ONE 220 Manual

De eN eS Fr
SUMMArY ACoUSTIC SIGNALS
permanent acoustic signal (piiiiiiiiiiiep):
During power-on a permanent signal is emitted for one second.
permanent acoustic signal after self-check (piep_piep_piep_...):
iPROBE ONE error
acoustic signal for 3 seconds after self-check (piep_piep_piep_...):
Battery replacement
permanent acoustic signal (tschip__tschip__tschip_...):
no active transmitter nearby
acoustic signal (piep_piep_piep_...):
active transmitter is nearby (approx. 0,5 to 2 m)
permanent acoustic signal (piiiiiiiiiiiep):
active transmitter is nearby (< approx. 50 cm)
5 short Beep-signals (piep-piep-piep-piep-piep_...):
Transmitter with iPROBE ONE Support is deactivated
acoustic signal (prrrrie):
During power-off an acoustic signal is emitted for 3 seconds
SUMMArY LeD-INDICATIoN
Continuous LED-signal:
During power-on both LED-indication lights will show for 1 second
Blinking LED-signal:
active transmitter is nearby (approx. 0,5 to 2 m)
Continuous LED-signal:
active transmitter is nearby (< approx. 50 cm)
20 | 08/12
IT CZ SK rU rU SK CZ IT

SpeCIFICATIoNS

TeCHNICAL DATA
Device designation
System
Receiving frequency
Power supply
Battery lifetime
Approaching range
Range target hit
Temperature range
PIEPS iproBE oNE
Weight (incl. battery)
Probing length (mechanically)
Probing length total
(mech. + electronic Target range)

WArrANTY CoNDITIoNS

• The device is guaranteed by the manufacturer against defects in material
and workmanship for a period of 2 years from the date of purchase.
• This warranty does not apply to damage caused by incorrect use, dropping
or dismantling of the device by unauthorized persons.
• Any further warranty or liability for consequential damage is
expressly excluded.
• Warranty claims should be addressed - enclosing the receipt of purchase –
to the relevant sales outlet.
CerTIFICATIoN: Warning: Any changes or modifications not expressly
approved by the manufacturer, responsible for compliance, could void the
user's authority to operate this device. Europe: Manufacturer: PIEPS GmbH,
Country of manufacture: Austria, Device type: PIEPS iPROBE ONE; Canada:
IC: 7262a-iproBE01, USa: fCC ID: rEMiproBE01; This device conforms to
Paragraph 15 of the FCC regulations. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device
must accept any interference received, including interference that may cause
undesired operation.
CoNForMITY: PIEPS GmbH declares hereby, that the product PIEPS iPROBE
ONE fulfills all requirements and regulations of directive 1999/5/EC! The
declaration of conformity can be downloaded at the following source: http://
www.pieps.com/certification
MANUFACTUrer, SALeS & SerVICe
pIEpS GmbH, Parkring 4, 8403 Lebring, Austria
E-mail: office@pieps.com, www.pieps.com
Fr eS eN De
PIEPS iPROBE ONE
Electronic avalanche probe with high
quality carbon and aluminum tubes
457 kHz (EN 300718)
1 battery, Alkaline (AA), LR06, 1.5V
150 h (Check A1)
2 m
0 – approx. 50 cm
-20°C to +45°C
220 260
350 g 390 g
1,80 m 2,20 m
max. max.
3,60 m 4,00 m
All information supplied
without liability.
11/2011
08/12 | 21