Table of Contents
Advertisement
Quick Links
Long-Range Barrier Sensors
Model
E-9626-2B190Q
E-9643-4B190Q
E-9661-6B190Q
E-9679-8B190Q
4 Different programmable frequencies
Range: Up to 190ft (60m) outdoor,
380ft (120m) indoor
End caps swivel for easy installation
Built-in heater for cold weather
operation
Note: Model numbers that end with "Q" or that have a round green "Q" sticker signify RoHS-compliant products.
Manual
# of Beams
2 pairs
4 pairs
6 pairs
8 pairs
Built-in tamper switches
Programmable trigger options
Form C relay output
Weatherproof IP65
AGC circuits ensure operation in rain,
fog, and low-temperature conditions
Length
26" (66cm)
43" (109cm)
61" (155cm)
79" (201cm)
Advertisement
Table of Contents
Related Manuals for SECO-LARM ENFORCER E-9626-2B190Q
Summary of Contents for SECO-LARM ENFORCER E-9626-2B190Q
- Page 1 Long-Range Barrier Sensors Manual Model # of Beams Length E-9626-2B190Q 2 pairs 26” (66cm) E-9643-4B190Q 4 pairs 43” (109cm) E-9661-6B190Q 6 pairs 61” (155cm) E-9679-8B190Q 8 pairs 79” (201cm) 4 Different programmable frequencies Built-in tamper switches Range: Up to 190ft (60m) outdoor, ...
-
Page 2: Table Of Contents
4 x Pole mount brackets 8 x Machine screws 4x6mm (for pole mount brackets) 8 x Machine screws 4x25mm (for pole mount brackets) 12 x Screws 6x20mm (for wall mount use) 12 x Plastic anchors (for wall mount use) SECO-LARM U.S.A., Inc. -
Page 3: Features
Humidity Ingress protection IP65 Case Aluminum housing / PC anti-UV cover / ABS end caps Dimensions See page 4, Dimensions for more details Weight (Tx & Rx) with brackets 5.5lb (2.5kg) 7.7lb (3.5kg) 12.1lb (5.5kg) 14.3lb (6.5kg) SECO-LARM U.S.A., Inc. -
Page 4: Dimensions
To use, twist the beams up to 90. Sample Applications: Typical Garages, door/window gates, and frame walls Windows Fence tops SECO-LARM U.S.A., Inc. -
Page 5: Overview - Inside The Sensor
Power switch (SW1) Ground Tamper Channel selection Beam alignment output switch (SW2) buzzer jumper (JP1) Tamper Tamper switch Channel selection switch switch (SW2) Swivel screw Swivel screw Red alignment/trigger Swivel screw Swivel screw Tamper switch Tamper switch SECO-LARM U.S.A., Inc. -
Page 6: Installation - Choosing A Location
Do not let sunlight or any direct beam of light shine one unit is at the top directly on the sensor. If unavoidable, mount in a and the other is at way that the transmitter – not the receiver – faces the bottom. the sun. SECO-LARM U.S.A., Inc. -
Page 7: Installation - Wall Vs. Pole Mounting
Connecting Multiple Units Fig. 7 – Linear protection Fig. 8 – Perimeter protection CH 3 (TX) CH 1 (TX) CH 4 (RX) CH 2 (RX) CH 3 (RX) CH 1 (RX) CH 4 (TX) CH 2 (TX) SECO-LARM U.S.A., Inc. -
Page 8: Installation - Running The Wires
(see Fig. 10). Using these holes as a template, mark their location on the wall with a pencil. 4. Connect the wires (see pg. 9) before permanently mounting the units to the wall. SECO-LARM U.S.A., Inc. -
Page 9: Installation - Connecting The Wires
4. Replace the end cap. NOTE: End cap must be off when aligning the sensor. 5. Use a screwdriver to tighten the screws holding the end cap in place. Fig. 11 – Receiver circuit board Fig. 12 – Transmitter circuit board SECO-LARM U.S.A., Inc. -
Page 10: Aligning The Beams
2. The latter (any single pair of beams broken) detection function can be disabled when the JP2 jumper is removed. Fig. 15 – Programming buzzer ON/OFF Fig. 16 – Jumper position (JP2) (JP1) and detection mode (JP2). Detection mode Detection mode SECO-LARM U.S.A., Inc. -
Page 11: Programming The Barrier Sensor
Transmitter circuit board Receiver circuit board Triggering the Barrier Sensor Fig. 19 – Ways to trigger the sensor Any two adjacent pair tripped Any single pair tripped Response time: programmable Response time: 2 seconds 150/300/450/600ms (Programmable, see page 10) SECO-LARM U.S.A., Inc. -
Page 12: Troubleshooting
This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.