PI C-414 Short Instructions
  1. Manuals
  2. Brands
  3. PI Manuals
  4. Controller
  5. C-663
  6. Short instructions

PI C-414 Short Instructions

Digital motor controllers and drivers
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Table of Contents

MS242EK 3.1.0 02/2021. 0.5
Page 1 of 8
Digital Motor Controllers and Drivers
Short Instructions
C-414 / C-663 / C-863 / C-867 / C-877 / C-884 / E-861 / E-871 /
E-872.401 / E-873
User Information
These short instructions contain an overview of the most important safety information and hand-
ling instructions for installation and startup of motor controllers and motor drivers (hereinafter
referred to as „electronics") with the above-mentioned product numbers.
Subject to change. These short instructions are superseded by any new release. The latest respec-
tive release is available for download on our website.
Downloading and Reading the Manual
The actions during installation, starting and operating, adapting the settings, and maintenance
require additional information from the manuals for the electronics and/or the positioner.
Manuals may be titled as follows: „User Manual", „Technical Note".
Downloading Manual Packages as ZIP File
If you received a CD from PI with the PI Software Suite, follow the instructions in the file
Manuals\A000T0081-Downloading Manuals from PI.pdf to download the manuals for your elec-
tronics.
Downloading Manuals from the Website
1. Open the website www.pi.ws.
2. Search the website for the product number (e.g., C-663.12) or the product family (e.g., PICMA®
Bender).
3. Click the corresponding product to open the product detail page.
4. Click Downloads.
The manuals are displayed under Documentation.
5. Click the desired manual and fill out the inquiry form.
The download link will then be sent to the email address entered.
If you cannot find the manual you are looking for or if you have any questions: Contact our custo-
mer service department via service@pi.de.
B E W E G E N | P O S I T I O N I E R E N
M O T I O N | P O S I T I O N I N G

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C-414 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for PI C-414

Summary of Contents for PI C-414

  • Page 1 Manuals may be titled as follows: „User Manual“, „Technical Note“. Downloading Manual Packages as ZIP File If you received a CD from PI with the PI Software Suite, follow the instructions in the file Manuals\A000T0081-Downloading Manuals from PI.pdf to download the manuals for your elec- tronics.

  • Page 2: General Safety Instructions

    PI. 1. Unpack the tar archive from the /linux Startup directory on the PI software CD to a direc- The collision of a moving part at the end of the tory on your PC. travel range, or with an obstacle, as well as high 2.
  • Page 3 ▪ Positioner with compatible drive type protective earth conductor ▪ If necessary: Compatible adapter from PI ▪ Mounting hardware for the protective ▪ If necessary: Suitable extension cable from earth conductor; is on the protective earth...
  • Page 4 MS242EK 3.1.0 02/2021. 0.5 Page 4 of 8 Connecting the PC Removing the Protective Cap If necessary: Remove the protective cap NOTICE from the power adapter connector on the Connecting the USB and RS-232 inter- electronics. faces of the electronics to the PC at the Electronics with M8 panel plug same time can damage the PC or the electronics.
  • Page 5 MS242EK 3.1.0 02/2021. 0.5 Page 5 of 8 ✔ If available: You have set the DIP switches Startup on the electronics according to your appli- cation (see manual). Electronics that are not a part of a daisy chain network must The PIMikroMove PC software is recommended have address 1, if they are to be used in for initial startup.

  • Page 6: Starting Motion

    MS242EK 3.1.0 02/2021. 0.5 Page 6 of 8 If the Select connected stages step is displayed PIMikroMove: Connect controller in the Start up controller window: PIMikroMove®: Select connected stages 1 Field for electronics selection 2 Tabs for interface and connection type 1 Stage database entries field 3 Interface parameters 2 Assign button 4 Connect button...
  • Page 7 MS242EK 3.1.0 02/2021. 0.5 Page 7 of 8 4. If necessary: Do the reference move during d. If available, click Auto Zero to start the Start up axes step and if necessary, the an autozero procedure (compensates autozero procedure for the axis. the weight force for drives without a.
  • Page 8 MS242EK 3.1.0 02/2021. 0.5 Page 8 of 8 Companies Subsidiaries Physik Instrumente (PI) GmbH & Co. KG US PI (Physik Instrumente) L.P. Auf der Roemerstrasse 1 www.pi-usa.us 76228 Karlsruhe GB PI (Physik Instrumente) Ltd. Germany www.physikinstrumente.co.uk Phone +49 721 4846-0 Fax +49 721 4846-1019 Physik Instrumente (PI) S.

This manual is also suitable for:

C-663C-863C-867C-877C-884E-861 ... Show all

Table of Contents