Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PSCS 11-12V
Summary of Contents for Trotec PSCS 11-12V
- Page 1 PSCS 11-12V ORIGINAL INSTRUCTIONS CORDLESS DRILL DRIVER...
-
Page 2: Table Of Contents
Follow the manual • Keep children and bystanders away while operating a Information marked with this symbol indicates that the power tool. Distractions can cause you to lose control. instructions must be observed. cordless drill driver PSCS 11-12V... -
Page 3: Safety
Use of the power tool for operations different the power tool on. A wrench or a key left attached to a from those intended could result in a hazardous situation. rotating part of the power tool may result in personal injury. cordless drill driver PSCS 11-12V... - Page 4 • Only charge the Li-Ion battery "PSCS 11-12V DC" (capacity General Power Tool Safety Warnings – Battery tool of 2.0 Ah = 1 battery cell) with the charger use and care "PSCS 11-12V AC".
- Page 5 • for drilling in wood, plastic, ceramic and metal, battery: whilst adhering to the technical data. Warning of explosion risk! We recommend using the power tool with original Trotec These symbols indicate the following: accessories. Do not expose the battery pack or tool to fire or...
- Page 6 Warning Make sure not to hit power, gas or water lines when working with a power tool. If necessary, use a pipe detector to check the wall you want to drill in or slit open. cordless drill driver PSCS 11-12V...
- Page 7 Only change the rotational direction when the device is at a standstill! Otherwise the device might be damaged. Note Set the torque and rotational direction according to the operating mode. A wrong selection may damage the device. cordless drill driver PSCS 11-12V...
-
Page 8: Information About The Device
LED work light Scope of delivery • 1 x Cordless drill driver PSCS 11-12V • 1 x Rechargeable battery • 2 x Bits (50 mm) • 1 x Quick charger • 1 x Transport case • 1 x Manual cordless drill driver PSCS 11-12V... - Page 9 Sound power level 74.07 dB (A) Uncertainty K 5 dB (A) Vibration information according to EN 62841 Vibration emission value for 1.58 m/s drilling in metal a Vibration emission value for 0.969 m/s screwing a Uncertainty K 1.5 m/s cordless drill driver PSCS 11-12V...
-
Page 10: Transport And Storage
• Check the contents of the transport case for completeness and look for damages. Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. cordless drill driver PSCS 11-12V... - Page 11 Allow the battery (7) to cool down to room temperature. 5. Remove the battery (7) from the quick charger (8). 3. If required, charge the battery (7) as described in the section Charging the battery. cordless drill driver PSCS 11-12V...
- Page 12 1. Set the switch for clockwise/counter-clockwise rotation (5) to centre position (lock). 5. Tighten the keyless drill chuck (1) by turning clockwise. 2. Turn the keyless drill chuck (1) counter-clockwise to open 3. If necessary, take the (drill) bit out of the drill chuck. cordless drill driver PSCS 11-12V...
- Page 13 ð Speed level 1: Speed of up to 400 rpm, suitable for all well as for unscrewing. screwing applications. ð Speed level 2: Speed of up to 1300 rpm, suitable for • For drilling, select the drilling setting indicated by the drilling. symbol cordless drill driver PSCS 11-12V...
-
Page 14: Operation
• Use a wood drill bit with centring tip. For deep drill holes, use an auger bit; for large drilling diameters, use a Forstner bit. cordless drill driver PSCS 11-12V... -
Page 15: Available Accessories
4. Remove the tool from the device (see Start-up chapter). • Check the quick charger for damages. Should the quick 5. Clean the device according to the Maintenance chapter. charger be damaged, stop using it. Contact the Trotec 6. Store the device according to the Storage chapter. customer service. -
Page 16: Maintenance
• Keep the connecting terminals on the device and charger device to an authorised specialist electrical company or to clean. Trotec for repair. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. cordless drill driver PSCS 11-12V... -
Page 17: Disposal
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life. - Page 18 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...