Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the operating manual must be observed. Operating manual – cordless drill driver PSCS 11-20V...
Use of a cord safety principles. A careless action can cause severe suitable for outdoor use reduces the risk of electric shock. injury within a fraction of a second. Operating manual – cordless drill driver PSCS 11-20V...
Page 4
• Keep handles and gripping surfaces dry, clean and free from oil and grease. Slippery handles and gripping surfaces do not allow for safe handling and control of the tool in unexpected situations. Operating manual – cordless drill driver PSCS 11-20V...
Page 5
Make sure that no water or other liquids can whilst adhering to the technical data. enter the housing. We recommend using the power tool with original Trotec accessories. Warning of explosive substances Do not expose the battery to temperatures above Improper use 45 °C! Do not let the battery come into contact with...
Page 6
Only change the rotational direction when the device is at a standstill! Otherwise the device might be damaged. Note Set the torque and rotational direction according to the operating mode. A wrong selection may damage the device. Operating manual – cordless drill driver PSCS 11-20V...
• 1 x Cordless drill driver PSCS 11-20V • 1 x Rechargeable battery • 2 x Bits (50 mm) • 1 x Quick charger • 1 x Belt clip • 1 x Transport case • 1 x Manual Operating manual – cordless drill driver PSCS 11-20V...
Page 8
Sound pressure level 69.5 dB(A) Sound power level 80.5 dB(A) Uncertainty K 3 dB(A) Vibration information according to EN 60745 Vibration emission value 1.03 m/s drilling in metal / screwing Uncertainty K 1.5 m/s Operating manual – cordless drill driver PSCS 11-20V...
– Only ship batteries if their housing is undamaged. – Mask open terminals with tape and pack the battery in a way that it cannot move inside the packaging. – Please also observe any other national regulations. Operating manual – cordless drill driver PSCS 11-20V...
Allow the battery (8) to cool down to room temperature. 5. Take the battery (8) out of the quick charger (9) by pressing and holding the unlocking button (15) and pulling the battery (8) off the quick charger (9). Operating manual – cordless drill driver PSCS 11-20V...
Page 11
(II.). rotation (4) to centre position (lock). 2. Turn the keyless drill chuck (1) counter-clockwise to open it. 3. If required, charge the battery (8) as described in the section Charging the battery. Operating manual – cordless drill driver PSCS 11-20V...
Page 12
• Select a low torque for smooth-running screws or soft materials. • Select a high torque for tight screws and hard materials as well as for unscrewing. • For drilling, select the drilling setting indicated by the symbol Operating manual – cordless drill driver PSCS 11-20V...
Page 13
1. Slide the gear selection (3) to the desired position. ð Speed level 1: Speed of up to 400 rpm, suitable for all screwing applications. ð Speed level 2: Speed of up to 1550 rpm, suitable for drilling. Operating manual – cordless drill driver PSCS 11-20V...
• Use a wood drill bit with centring tip. For deep drill holes, use an auger bit; for large drilling diameters, use a Forstner bit. Operating manual – cordless drill driver PSCS 11-20V...
• Check the quick charger for damages. Should the quick 3. Remove the battery from the device (see Start-up chapter). charger be damaged, stop using it. Contact the Trotec 4. Remove the tool from the device (see Start-up chapter). customer service.
Trotec for repair. • Keep the connecting terminals on the device and charger clean. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. Operating manual – cordless drill driver PSCS 11-20V...
Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006 on batteries and accumulators. Please dispose of batteries and accumulators according to the relevant legal requirements. Operating manual – cordless drill driver PSCS 11-20V...
Page 19
Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...