Advertisement
Quick Links
SSV40108HAC
SSV40108HDAC
SSV40108HDC
SSV40108HDDC - Hydraulic Hoist, Deep Water, with 12 Volt Pump
Midwest Industries, Inc.
Page 1
- Hydraulic Hoist with 120 Volt Pump
- Hydraulic Hoist, Deep Water, with 120 Volt Pump
- Hydraulic Hoist with 12 Volt Pump
Ida Grove, IA 51445
800.859.3028
www.shorestation.com
0003277
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ShoreStation SSV40108HAC
Summary of Contents for ShoreStation SSV40108HAC
- Page 1 SSV40108HAC - Hydraulic Hoist with 120 Volt Pump SSV40108HDAC - Hydraulic Hoist, Deep Water, with 120 Volt Pump SSV40108HDC - Hydraulic Hoist with 12 Volt Pump SSV40108HDDC - Hydraulic Hoist, Deep Water, with 12 Volt Pump Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028...
- Page 2 DC Powered Pumps - Troubleshooting ......28 12 Volt Pump Drawing/Assembly Instructions ..... 14 DC Powered Hoists - General Elec Troubleshooting ..28 Bundles Required SSV40108HAC SSV40108HDAC Aluminum V-Frame 4000 lb. Hydraulic Hoist with AC Drive Alum. V-Frame 4000 lb. Hyd. Deep Water Hoist w/AC Drive...
- Page 3 Diagram A Post No. 2 Post No. 1 Post No. 3 Lower Side Frame 5x2x131” Lower Frame Tube 5x2x107” Post No. 4 Bottom Corner Cable Bracket Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 4...
- Page 4 Locate one of the lower frame tubes (107”for a SSV10408 series or 119”for the SSV40120 series ) and slide one end of the lower frame tube over the leg of the lower corner block leg as shown. See Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 5...
- Page 5 Cable end attaches to Bottom Corner Cable Bracket Cable Guide Holes for attaching plat- form rail extrusions to the platform. Identical hole pattern located on either side of platform. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 6...
- Page 6 Locate the two platform rail extrusions (Item No. 5 in Diagram B). They are punched the same on both ends eliminating a right and left part. Place one of the platform rail extrusions between the two Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 7...
- Page 7 Insert level cable in this hole. Diagram C Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 8...
- Page 8 Attach the step assembly to the drop side weldment using two (2) 3/8” X 3-7/16” X 3” square u-bolts and secure with 3/8” lock washers and 3/8” hex nuts. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 9...
- Page 9 Diagram E Winch Tube Assembly Winch Tube Assembly Pre-drilled hole for attaching motor mount brackets. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 10...
- Page 10 Place a second 2” top clamp on the post and the pump box. drop down and around the winch tube assembly. Align the holes in Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 11...
- Page 11 Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 12...
- Page 12 Place a ¼” x 2 ¼” hex bolt into the second hole in the control arm tube and the control arm pivot weldment. Secure using a ¼” hex nut. Tighten. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 13...
- Page 13 The correct connector is identified below on the drawing. Once mated turn the outside sleeve of the connector clockwise to lock the connection together. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 14...
- Page 14 Attach the end fitting on the red cable to the large solenoid terminal for the motor. It is the post on the solenoid opposite the one that has a heavy cable attaching the solenoid to the motor windings. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 15...
- Page 15 The red cable is for the positive post connections while the black is for the ground. See page 14 for the instructions on how to connect your battery to the motor. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 16...
- Page 16 SSV40108H Winch Tube Cable Diagram Side View Lift Cable Winch Cable 3110364 3110365 Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 18...
- Page 17 Should you have any questions regarding bly. Lower until the cylinder is fully extended and the cables can not the cables or pulleys, contact your local ShoreStation dealer. be extended any further. Midwest Industries, Inc.
- Page 18 Repeat the above process on the remaining bunk assembly on the other side of the hoist. is a good starting point. The bunks may need to be adjusted in a Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 20...
- Page 19 Once the assembly is in the proper position, tighten the nuts on the u-bolts. Assembly is complete. Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorestation.com 0003277 Page 21...
Need help?
Do you have a question about the SSV40108HAC and is the answer not in the manual?
Questions and answers