Contents Motorcycle Safety P. 2 Operation Guide P. 16 Maintenance P. 35 Troubleshooting P. 79 Information P. 98 Specifications P. 122 Index P. 126...
Page 2
When service is required, remember that Honda motorcycle. Your selection of a your Honda dealer knows your motorcycle Honda makes you part of a worldwide family best. If you have the required mechanical of satisfied customers who appreciate “know-how” and tools, you can purchase an Honda’s reputation for building quality into...
Page 3
A Few Words About Safety Your safety, and the safety of others, is very DANGER important. Operating this motorcycle safely is You WILL be KILLED or SERIOUSLY an important responsibility. HURT if you don’t follow instructions. To help you make informed decisions about safety, we have provided operating WARNING procedures and other information on safety...
Safety Guidelines Safety Guidelines Before Riding Make sure that you are physically fit, mentally Follow these guidelines to enhance your safety: focused and free of alcohol and drugs. Check Perform all routine and regular inspections ● that you and your passenger are both wearing specified in this manual.
Page 6
Safety Guidelines We recommend that all riders take a certified Make Yourself Easy to See course approved by the Motorcycle Safety Make yourself more visible, especially at night, Foundation (MSF). New riders should start with by wearing bright reflective clothing, the basic course, and even experienced riders positioning yourself so other drivers can see will find the advanced course beneficial.
Page 7
Safety Guidelines check the tightness of critical nuts and bolts, Keep Your Honda in Safe Condition and check the handlebar, control levers, brakes, It’s important to keep your motorcycle properly and wheels. Ride slowly and cautiously. maintained and in safe riding condition.
Page 8
Safety Guidelines Carbon Monoxide Hazard Exhaust contains poisonous carbon monoxide, a colorless, odorless gas. Breathing carbon monoxide can cause loss of consciousness and may lead to death. If you run the engine in a confined or even partly enclosed area, the air you breathe could contain a dangerous amount of carbon monoxide.
Safety Labels Safety Labels hazards that could cause serious injury. Read these labels carefully and don’t remove them. Safety and information labels on your If a label comes off or becomes hard to read, motorcycle provide important safety contact your dealer for a replacement. information and may warn you of potential...
Safety Precautions Safety Precautions Face shield with unobstructed field of vision ● or other approved eye protection Ride cautiously and keep your hands on the ● handlebars and feet on the footpegs. Look for a DOT (Department of Keep passenger’s hands on to the seat strap Transportation) certification label on any helmet ●...
Riding Precautions ❙ Riding Precautions Boots or Riding Shoes Sturdy boots with non-slip soles and ankle protection Running-in Period ❙ During the first 300 miles (500 km) of running, Jacket and Pants follow these guidelines to ensure your Protective, highly visible, long-sleeved jacket motorcycle’s future reliability and performance.
Page 13
Riding Precautions ❙ Exercise caution on low traction surfaces. Combined ABS (VT1300CRA/CTA only) ● The tires slip more easily on such surfaces Your motorcycle's rear brake system is linked to and braking distances are longer. the front brake. This means that operating the Avoid continuous braking.
Page 14
Riding Precautions ❙ This model is also equipped with an Anti-lock Wet or Rainy Conditions Brake System (ABS) designed to help prevent Road surfaces are slippery when wet, and wet the brakes from locking up during hard braking. brakes further reduce braking efficiency. ABS does not reduce braking distance.
Page 15
Riding Precautions To reduce the likelihood of theft, always lock ● Refueling and Fuel Guidelines the handlebar and remove the key when Follow these guidelines to protect the engine leaving the motorcycle unattended. and catalytic converter: Use of an anti-theft device is also Use only unleaded gasoline.
Loading Loading WARNING Carrying extra weight affects your ● Overloading or improper loading can motorcycle’s handling, braking and stability. cause a crash and you can be seriously Always ride at a safe speed for the load you hurt or killed. are carrying.
Page 19
(VT1300CR/CRA) Spark plug (P60) Clutch lever (P73) Ignition switch Fuel fill cap (P30) (P26) Engine oil fill cap/dipstick (P63) Seat (P54) Spark plug (P60) Battery (P56) Main fuse (P97) Final drive gear oil fill cap (P69) Shift lever (P29) Final drive gear oil drain bolt...
Page 21
(VT1300CT/CTA) Ignition switch (P26) Spark plug (P60) Clutch lever (P73) Fuel fill cap (P30) Engine oil fill cap/dipstick (P63) Spark plug (P60) Seat (P54) Saddlebag (P34) Battery (P56) Main fuse (P97) Final drive gear oil fill cap (P69) Shift lever (P29) Final drive gear oil drain bolt (P70)
Page 22
Instruments Odometer [Odo], Tripmeter [Trip A/B] & Clock (12-hour display) Select/Reset button switches between Select/Reset button odometer, tripmeters & clock. USA: Odometer & tripmeter read in miles. • Odometer: Total distance ridden. Canada: Odometer & tripmeter read in • Tripmeter: Distance ridden since tripmeter kilometers.
Page 23
To set the clock: Press the select/reset button until the desired minute is displayed. Turn the ignition switch on. Select the clock. Press and hold the select/reset button until Press and hold the select/reset button until the hour digits start flashing. the display stop flashing.
Page 24
Indicators ABS (Anti-lock Brake System) indicator (VT1300CRA/CTA) Comes on when the ignition switch is turned on. Goes off when your speed reaches approximately 6 mph (10 km/h). If it comes on while riding: (P83) High coolant temperature indicator If it comes on while riding: (P81) Fuel reserve indicator When this indicator comes on, remaining fuel...
Page 25
Neutral indicator Comes on when the transmission is in Neutral. Turn signal indicator High beam indicator PGM-FI (Programmed Fuel Injection) malfunction indicator lamp (MIL) Comes on briefly when the ignition switch is turned on with the engine stop switch in the RUN position.
Page 26
Switches (VT1300CR/CRA) Engine stop switch Should normally remain in the position. In an emergency, switch to OFF the position to stop the engine. Start button Headlight turns off when Turn signal switch operating the starter motor. Pressing the switch turns the turn signal off.
Page 27
(VT1300CT/CTA) Engine stop switch Should normally remain in the position. In an emergency, switch to OFF the position to stop the engine. Start button Headlight turns off when operating the starter motor. Turn signal switch Pressing the switch turns Horn button the turn signal off.
Page 28
Ignition Switch Switches the electrical system on/off. Push Key can be removed when in the OFF position. Turn Steering lock ley Turns electrical system on for starting/riding. Turn ❙ Locking Turn the handlebar all the way to the left. Turns engine off. Insert the steering lock key in the steering lock and turn it counterclockwise, then push Steering Lock...
Page 29
Starting the Engine Start your engine using the following NOTICE procedure, regardless of whether the engine • If the engine does not start within 5 seconds, turn the is cold or warm. ignition off and wait 10 seconds before trying to start the engine again to recover battery voltage.
Page 30
If the engine does not start: Open the throttle fully and press the start button for 5 seconds. Repeat the normal starting procedure. If the engine starts, open the throttle slightly if idling is unstable. If the engine does not start, wait 10 seconds before trying steps &...
Page 31
From 4th to 5th 31 mph (50 km/h) shift lever down with your heel. Shifting Down (VT1300CR/CRA) (VT1300CT/CTA) From 5th to 4th 22 mph (35 km/h) From 4th to 3rd 16 mph (25 km/h)
Page 32
Refueling Opening the Fuel Fill Cap Ignition key Open the lock cover, insert the ignition key, Filler neck and turn it clockwise to open the cap. Fuel level (max) Closing the Fuel Fill Cap Fuel filler After refueling, align the fuel fill cap latch opening with the slot in the filler neck.
Page 33
Storage Equipment ❙ Helmet Holder Unlocking Helmet holder is located on the left side Insert the ignition key and turn it below the seat. counterclockwise. Helmet holder ❙ Locking Hang your helmet on the holder pin and push it in to lock. Remove the key.
Page 34
Storage Equipment (Continued) Document Bag Store your other documents in the document Store your owner’s manual in the document bag attached to the rear fender under the bag attached to the inside of the right side seat. cover. ❙ Removing the Seat (P54) ❙...
Page 35
Tool Kit Removing the Ignition Switch The tool kit is stored on the face of the Cover ignition switch case behind the ignition Remove the clips. (P55) switch cover. Remove the ignition switch cover. Clip Tool kit Ignition switch case Installing the Ignition Switch Cover Install the parts in the reverse order of...
Page 36
Storage Equipment (Continued) Saddlebag (VT1300CT/CTA) Opening the Saddlebag Never exceed the maximum weight limit. Pull the lever up and open the lid. Maximum Weight: 10 lb (4.5 kg) Closing the Saddlebag Lever Push the lid closed and check that it is secure.
Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefully before attempting any maintenance. Refer to “Specifications” for service data. An optional larger tool kit may be available. Check with your Honda dealer’s parts department. Importance of Maintenance ..... P. 36 Engine Oil ...........P.
Importance of Maintenance For information about the exhaust emission and Importance of Maintenance noise emission requirements of the U.S. Keeping your motorcycle well-maintained is Environmental Protection Agency (EPA), the absolutely essential to your safety and to California Air Resources Board (CARB), and protect your investment, obtain maximum Environment Canada (EC).
Page 39
Importance of Maintenance Maintenance Safety Always read the maintenance instructions before you begin each task, and make sure that you have the tools, parts, and skills required. We cannot warn you of every conceivable hazard that can arise in performing maintenance.
If you sell the motorcycle, these receipts should be transferred with the Maintenance work should be performed in motorcycle to the new owner. accordance with Honda’s standards and specifications by properly trained and equipped technicians. Your dealer meets all of these requirements. Keep an accurate record of maintenance to help ensure that your motorcycle is properly maintained.
Page 41
– Evaporative Emission Control System – Maintenance Level : Intermediate. We recommend service by your Honda dealer, : Technical. In the interest of safety, have your motorcycle unless you have the necessary tools and are mechanically serviced by your dealer.
Page 42
Maintenance Schedule Frequency Odometer Reading × 1,000 mi Refer to page Items × 1,000 km 12.8 19.2 25.6 32.0 38.4 Final Drive Oil Brake Fluid Brake Pads Wear Brake System Brake Light Switch Headlight Aim Clutch System Side Stand Suspension Nuts, Bolts, Fasteners –...
Maintenance Fundamentals Brakes-Check operation; Pre-ride Inspection ● Front and Rear: check brake fluid level To ensure safety, it is your responsibility to ) and pads wear. P. 71 P. 72 perform a pre-ride inspection and make sure Lights and horn-Check that lights, ●...
Page 44
Maintenance Fundamentals Also, check the odometer reading against the Periodic Checks Maintenance Schedule and perform all You should also perform other periodic maintenance that is due. P. 38 maintenance checks at least once a month regardless of how often you ride, or more often if you ride frequently.
Page 45
Maintenance Fundamentals Replacing Parts Color label Always use Honda Genuine Parts or their equivalents to ensure reliability and safety. When ordering colored components, specify the model name, color, and code mentioned on the color label. The color label is attached to the frame under the seat.
Page 46
Maintenance Fundamentals Electrolyte splashes into your mouth: ● Battery Rinse mouth thoroughly with water, and Your motorcycle has a maintenance-free type do not swallow. battery. You do not have to check the battery WARNING electrolyte level or add distilled water. Clean the battery terminals if they become dirty or The battery gives off explosive corroded.
Page 47
30 days using a charger designed specifically for 3. If the terminals are heavily corroded, clean your Honda, which can be purchased from your the terminals with a wire brush or sandpaper. dealer. Read the information that came with Wear safety glasses.
Page 48
Jump starting using an automobile battery can damage your motorcycle’s electrical system and is not recommended. Bump starting is also not recommended. NOTICE Installing non-Honda electrical accessories can overload the electrical system, discharging the battery and possibly NOTICE damaging the system.
Page 49
The API classification specifies the quality and performance rating of engine oils. Use SG or If you use non-Honda engine oil, check the label higher oils, excluding oils marked as “Energy to make sure that the oil satisfies all of the Conserving”...
Page 50
Brake Fluid Recommended Coolant Do not add or replace brake fluid, except in an Pro Honda HP is a pre-mixed solution of emergency. Use only fresh brake fluid from a antifreeze and distilled water. sealed container. If you do add fluid, have the...
Page 51
Maintenance Fundamentals Air Cleaner Tires (Inspecting/Replacing) ❙ Checking the Air Pressure This motorcycle is equipped with a viscous type air cleaner element. Visually inspect your tires and use an air Compressed air cleaning or any other cleaning pressure gauge to measure the air pressure at can degrade the viscous element performance least once a month or any time you think the and cause the intake of dust.
Page 52
Maintenance Fundamentals ❙ Inspecting for Abnormal Wear WARNING Inspect the tires for signs of abnormal Riding on tires that are excessively wear on the contact worn or improperly inflated can cause surface. a crash in which you can be seriously hurt or killed.
Page 53
Always use the size and type of tires Have the wheel balanced with Honda ● recommended in this owner’s manual. Genuine balance weights or equivalent after the tire is installed.
Page 54
Maintenance Fundamentals ❙ Tire Identification Number (TIN) Tire Service Life The tire identification number (TIN) is a group of The service life of your tires is dependent on numbers and letters located on the sidewall of many factors, including, but not limited to, the tire.
Removing & Installing Body Components Side Cover Grommets Prongs The right side cover must be removed to remove the seat, to service the circuit fuses and to access the owner’s manual. The left side cover must be removed to remove the seat, to service the main fuse and the battery.
Removing & Installing Body Components Seat ❙ Seat Removal 1. Remove the right and left side covers. P. 53 Bolt B Tabs Collar A 2. Remove the bolts A, collars A and collars Collar B 3. Remove the bolt B. 4.
Removing & Installing Body Components Clip ❙ Clip Installation 1. Slightly open the retaining pawls and then The clip must be removed to access the tool push them out. kit. 2. Insert the clip into the hole. ❙ 3. Press down on the center pin to lock the Removal clip.
Removing & Installing Body Components Battery Battery 3. Disconnect the negative terminal from the battery. 4. Disconnect the positive terminal from Battery band Positive terminal the battery. 5. Remove the battery taking care not to drop the terminal nuts. ❙ Installation Install the parts in the reverse order of removal.
Throttle Checking the Throttle Adjusting the Throttle Freeplay With the engine off, check that the throttle 1. Slide the cable boot. rotates smoothly from fully closed to fully 2. Loosen the lock nut. open in all steering positions and throttle 3.
Air Cleaner Changing Air Cleaner Element 6. Tighten the bolts. Torque: 1.1 lbf·ft (1.5 N·m, 0.2 kgf·m) Use a new Honda Genuine air cleaner element or an equivalent specified for your Air cleaner element Air cleaner motorcycle. housing cover NOTICE Using the wrong air cleaner element can result in serious damage to the engine.
Spark Plug Checking Spark Plug Grommets Rear over head cover For the recommended spark plug, see “Specifications.” P. 123 Use only the recommended type of spark plug in the recommended heat range. NOTICE Using spark plugs an improper heat range can cause engine damage.
Page 63
Spark Plug Checking Spark Plug Front over head center Spark plug cap cover Bolt Washer Prongs Front over head cover Grommets 5. Disconnect the spark plug cap. 8. Inspect the electrodes and center 6. Clean any dirt from around the spark porcelain for deposits, erosion or carbon plug base.
Page 64
Spark Plug Checking Spark Plug 9. Check the spark plug gap using a wire- 12. Tighten the spark plug: type feeler gauge. If the old plug is good: ● If adjustment is necessary, bend the 1/8 turn after it seats side electrode carefully.
Engine Oil Checking the Engine Oil Oil fill cap/dipstick 1. If the engine is cold, idle the engine for 3 to 5 minutes. Upper level 2. Turn the ignition switch off, stop the engine and wait 2 to 3 minutes. 3.
Page 66
Engine Oil Adding Engine Oil Adding Engine Oil NOTICE Overfilling with oil or operating with insufficient oil can If the engine oil is below or near the lower cause damage to your engine. Do not mix different brands level mark, add the recommended engine oil. and grades of oil.
Page 67
We recommend that you have your Sealing washers motorcycle serviced by your dealer. Use a new Honda Genuine oil filter or equivalent specified for your model. NOTICE Using the wrong oil filter can result in serious damage to the engine.
Page 68
Engine Oil Changing Engine Oil & Filter 6. Remove the oil filter with a filter wrench 7. Apply a thin coat of engine oil to the and let the remaining oil drain out. Make rubber seal of a new oil filter. sure the prior seal is not stuck to the 8.
Coolant Checking the Coolant If the coolant level is dropping noticeably or the reserve tank is empty, you likely have a 1. Place your motorcycle on a firm, level serious leak. Have your motorcycle inspected surface. by your dealer. 2. Check that the coolant level is between the UPPER and LOWER level marks in the Adding Coolant reserve tank.
Page 70
Coolant Changing Coolant 2. Remove the bolt. 5. Securely reinstall the cap. 3. Pull the left rear cover out until the prongs 6. Install the parts in the reverse order of are clear of the grommets. Remove the removal. left rear cover. WARNING 4.
Final Drive Oil Checking the Final Drive Oil Adding Final Drive Oil 1. Place your motorcycle on the side stand If the final drive oil level is low, check for oil on a level surface. leaks. Add the recommended final drive oil 2.
Page 72
Final Drive Oil Changing Final Drive Oil Changing Final Drive Oil 4. Install a new sealing washer onto the drain bolt. Tighten the drain bolt. 1. Place your motorcycle on the side stand Torque: 9 lbf·ft (12 N·m, 1.2 kgf·m) on a level surface.
Brakes Checking Brake Fluid If the brake fluid level in either reservoir is below the LOWER level mark or the brake 1. Place your motorcycle in an upright lever and pedal freeplay becomes excessive, position on a firm, level surface. inspect the brake pads for wear.
Page 74
Brakes Inspecting the Brake Pads Inspecting the Brake Pads Inspect the brake pads from in the Front bottom of the brake caliper. Check the condition of the brake pad groove Always inspect both left and right wear indicators. The pads need to be calipers.
Clutch Checking the Clutch Check the clutch cable for kinks or signs of wear. If necessary have it replaced by your dealer. ❙ Checking the Clutch Lever Freeplay Lubricate the clutch cable with a commercially available cable lubricant to Check the clutch lever freeplay. prevent premature wear and corrosion.
Page 76
Clutch Adjusting the Clutch Lever Freeplay Adjusting the Clutch Lever Upper lock nut Freeplay ❙ Upper Adjustment Attempt adjustment with the upper clutch – cable adjuster first. 1. Loosen the upper lock nut. 2. Turn the upper clutch cable adjuster until Upper clutch cable adjuster the freeplay is 3/8 to 13/16 in (10 to 20 mm).
Page 77
Clutch Adjusting the Clutch Lever Freeplay 1. Loosen the upper lock nut and turn the Lower lock nut upper clutch cable adjuster all the way in (to provide maximum freeplay). Tighten the upper lock nut. – 2. Loosen the lower lock nut. 3.
Side Stand 4. Start the engine, pull the clutch lever in, and shift the transmission into gear. 5. Lower the side stand all the way. The engine should stop as you lower the side stand. If the engine doesn’t stop, have your motorcycle inspected by your dealer.
Other Adjustments Adjusting the Rear Suspension Adjuster Punch mark ❙ Rebound Damping You can adjust the rebound damping by the adjuster to suit the load or the road surface. Turn clockwise to increase rebound damping Reference (hard), or turn counterclockwise to decrease punch mark rebound damping (soft).
Other Adjustments Adjusting the Headlight Aim Adjusting the Headlight Aim Adjusting the Brake Light Switch You can adjust vertical aim of the headlight for proper alignment. To move the headlight Check the operation of the brake light case, loosen the bolts. switch.
Troubleshooting Engine Will Not Start......... P. 80 Electrical Trouble........P. 92 Overheating (High coolant temperature Battery Goes Dead ........P. 92 indicator is on) ......... P. 81 Burned-out Light Bulb .......P. 92 Blown Fuse..........P. 96 Warning Indicators On or Flashing ..P. 82 Low Oil Pressure Indicator ......
Engine Will Not Start ❙ ❙ Starter Motor Operates But Engine Starter Motor Does Not Operate Does Not Start Check the following items: Check the following items: Make sure engine stop switch is RUN ● Check the correct engine starting position P.
Overheating (High coolant temperature indicator is on) The engine is overheating when the If the fan is not operating: following occurs: Suspect a fault. Do not start the engine. High coolant temperature indicator comes Transport your motorcycle to your dealer. ●...
Warning Indicators On or Flashing Low Oil Pressure Indicator If the engine oil level goes down rapidly, your motorcycle may have a leak or another If the low oil pressure indicator comes on, serious problem. Have your motorcycle pull safely to the side of the road and stop inspected by your dealer.
Warning Indicators On or Flashing ABS (Anti-lock Brake System) Indicator (VT1300CRA/CTA only) ABS (Anti-lock Brake System) The ABS indicator may come on if you turn the rear wheel while your motorcycle is lifted Indicator (VT1300CRA/CTA off the ground. In this case, turn the ignition only) switch off and then on again.
Tire Puncture Repairing a puncture or removing a wheel WARNING requires special tools and technical expertise. We recommend you have this type of service Riding your motorcycle with a performed by your dealer. temporary tire repair can be risky. If After an emergency repair, always have the the temporary repair fails, you can tire inspected/replaced by your dealer.
Page 87
Tire Puncture Removing Wheels (VT1300CRA/CTA only) 4. Support your motorcycle securely and When removing and installing the wheel, be raise the front wheel off the ground using careful not to damage the wheel speed a maintenance stand or a hoist. sensor and pulser ring.
Page 88
Tire Puncture Removing Wheels Installation 4. Tighten the right axle pinch bolts to hold 1. Attach the side collars to the wheel. the axle. 2. On the right side, place the wheel 5. Tighten the axle bolt. between the fork legs and insert the Torque: 47 lbf·ft (64 N·m, 6.5 kgf·m) front axle shaft, through the right fork 6.
Page 89
Tire Puncture Removing Wheels 10. Check the clearances between each If a torque wrench was not used for surface of the brake disc and the brake installation, see your dealer as soon as bracket (not the brake pads) are possible to verify proper assembly. symmetrical.
Page 90
Tire Puncture Removing Wheels ❙ Rear Wheel 3. Remove the muffler bracket bolt A, bolt B, nuts and washers. Removal 4. Remove the muffler. 1. Park on a firm, level surface. Nuts Muffler bracket bolt A 2. Remove the exhaust pipe joint nuts. Rear Front Washers...
Page 91
Tire Puncture Removing Wheels 5. While holding the other end of the rear Rear brake bracket Protective tape axle shaft with a wrench, remove the rear axle nut and washer. 6. Loosen the axle holding bolt and washer. 7. Support your motorcycle securely and raise the rear wheel off the ground using a maintenance stand or a hoist.
Page 92
Before installing the wheel, check that the wheel hub, rear brake bracket. wheel hub and final drive gear splines are coated with molybdenum disulfide paste. Recommended molybdenum disulfide paste: (USA only) Pro Honda Moly 60 paste or equivalent...
Page 93
Tire Puncture Removing Wheels 5. Remove the protective tape or an Before installing the muffler, replace the equivalent. exhaust pipe gasket with a new gasket. 6. Install the rear axle nut and washer. 10. Tighten the nuts and bolts. Tighten the rear axle nut. Exhaust pipe joint nut: Torque: 94 lbf·ft (127 N·m, 13.0 kgf·m) Torque: 17 lbf·ft (23 N·m, 2.3 kgf·m)
Electrical Trouble Battery Goes Dead Burned-out Light Bulb Charge the battery using a motorcycle Follow the procedure below to replace a battery charger. burned-out light bulb. Remove the battery from the motorcycle Turn the ignition switch to the OFF position. while charging.
Page 95
Electrical Trouble Burned-out Light Bulb ❙ Headlight Bulb Seat rubber TOP mark Grommet Bolt Tabs Headlight Bulb Bolt Bolt Connector Bolt 5. Remove the seat rubber. 1. Remove the bolts from the headlight case. 6. Unhook the pin and remove the bulb. 2.
Page 96
Electrical Trouble Burned-out Light Bulb ❙ ❙ Brake/Taillight Bulb Front/Rear Turn Signal Bulb Bulb Taillight lens Bulb Turn signal lens Lens packing Screws Screw 1. Remove the taillight lens by removing the 1. Remove the turn signal lens and lens screws.
Page 97
Electrical Trouble Burned-out Light Bulb ❙ License Plate light Bulb License light cover 1. Remove the screws and license light Bulb cover. 2. Pull the bulb out of the socket without turning it. 3. Install a new bulb and parts in the reverse order of removal.
Electrical Trouble Blown Fuse Blown Fuse 1. Remove the right side cover. P. 53 2. Remove the fuse box cover. Before handling fuses, see “Inspecting and 3. Pull the fuses out one by one check for a Replacing Fuses.” P. 46 blown fuse.
Page 99
Electrical Trouble Blown Fuse ❙ Main Fuse 1. Remove the left side cover. P. 53 2. Disconnect the wire connector of the starter magnetic switch. Main fuse Wire 3. Pull the main fuses out and check for a connector blown fuse. Always replace a blown fuse with a spare of the same rating.
Information Keys.............P. 99 Honda Contacts ........P. 119 Instruments, Controls, & Other Features ... P. 100 Reporting Safety Defects ..... P. 121 Caring for Your Motorcycle.....P. 101 Storing Your Motorcycle ......P. 105 Transporting Your Motorcycle ....P. 106 You & the Environment ......P. 107 Vehicle Identification Number ....P.
Keys Keys Ignition key/Steering lock key Be sure to record the key number provided with the original keys. Store the spare key and recorded key number in a safe location. To make a duplicate, take the spare key or the key number to a locksmith.
Instruments, Controls, & Other Features Instruments, Controls, & Tripmeter Other Features The tripmeter returns to 0.0 when the read-out exceeds 999.9. Ignition Switch Document Bag The headlight is always on when the ignition switch is on. Leaving the ignition switch on with The owner’s manual, registration, and the engine stopped will drain the battery.
Frequent cleaning and polishing is important to 3. Thoroughly rinse your motorcycle with plenty ensure the life of your Honda. A clean of clean water and dry with a soft, clean motorcycle makes it easier to spot potential cloth.
Page 104
Caring for Your Motorcycle ❙ Washing Precautions Do not direct water near the headlight: ● Follow these guidelines when washing: Any condensation inside the headlight Do not use high-pressure washers: should dissipate after a few minutes of ● High-pressure water cleaners can damage running the engine.
Page 105
Caring for Your Motorcycle Aluminum Components Exhaust Pipe and Muffler Aluminum will corrode from contact with dirt, The exhaust pipe and muffler are stainless steel mud, or road salt. Clean aluminum parts but may become stained by mud or dust. To regularly and follow these guidelines to avoid remove mud or dust, use a wet sponge and a scratches:...
Page 106
Caring for Your Motorcycle Replace the windscreen if scratches cannot be Windscreen (VT1300CT/CTA) removed and they obstruct clear vision. Using plenty of water, clean the windscreen with a soft cloth or sponge. (Avoid using Take care to keep battery electrolyte, brake detergents or any kind of chemical cleaner on fluid, or other chemical solvents off the the windscreen.) Dry with a soft, clean cloth.
Storing Your Motorcycle Storing Your Motorcycle Twice a year, at the beginning and end of the riding season, perform a ‘‘deep’’ clean that may require three or four applications of the leather If you store your motorcycle outdoors, you cleaner. After cleaning, apply a high-quality should consider using a full-body motorcycle leather conditioner (neatsfoot oil, mink oil, etc.) cover.
If your motorcycle needs to be transported, it For more information about storage, should be carried on a motorcycle trailer or a refer to the Honda Winter Storage Guide, flatbed truck or trailer that has a loading ramp available from your dealer.
You & the Environment You & the Environment drain or on the ground. Used oil, gasoline, coolant, and cleaning solvents contain poisons Owning and riding a motorcycle can be that can hurt refuse workers and contaminate enjoyable, but you must do your part to protect drinking water, lakes, rivers, and oceans.
Vehicle Identification Number Vehicle Identification Number The VIN and engine serial numbers uniquely identify your motorcycle and are required in order to register your motorcycle. They may also be required when ordering replacement parts. The VIN number is stamped on the right side of the steering head and also appears on the Safety Certification Label attached to the left side of the down tube.
Emission Control Systems Emission Control Systems Engine number Your motorcycle engine emits combustion byproducts, including carbon monoxide (CO), oxides of nitrogen (NOx), and hydrocarbons (HC). Gasoline evaporation also emits hydrocarbons. Controlling the production of NOx, CO, and HC is important for the environment.
Page 112
Compliance with the terms of the Distributor’s The EPA requires that motorcycles built after Warranties for Honda Motorcycle Emission January 1, 1983 comply with applicable noise Control Systems is necessary in order to emission standards for one year or 3,730 miles...
Page 113
The exhaust emission control system includes air into the exhaust gas to help improve the following components that should not need emission control performance. adjustment, although periodic inspection by your Honda dealer is recommended. ❙ Catalytic Converters The exhaust system contains one or more ❙...
Page 114
Emission Control Systems Crankcase Emissions Control System Noise Emission Control System ❙ TAMPERING WITH THE NOISE CONTROL The positive crankcase ventilation system prevents gases that build up in the engine’s SYSTEM IS PROHIBITED: crankcase from being released into the U. S. federal law prohibits, and Canadian atmosphere.
Page 115
Emissions FOLLOWING ACTS: Have your motorcycle inspected and repaired by 1. Removal of, or puncturing the muffler, your Honda dealer if you experience any of the baffles, header pipes or any other component following symptoms: which conducts exhaust gases. Hard starting or stalling after starting ●...
A defective catalytic converter contributes to air riding and turn off the engine. Have your pollution and can impair your engine’s motorcycle serviced as soon as possible. performance. A replacement unit must be an original Honda part or equivalent.
Oxygenated Fuels Oxygenated Fuels If you accidentally fill your fuel tank with an oxygenated fuel containing higher percentages, Some conventional fuels blended with alcohol you may experience performance problems. To or an ether compound are available in some resolve the problem, have your dealer drain the locales to help reduce emissions to meet clean fuel tank and replace with the correct fuel.
Authorized Manuals various systems on Honda motorcycles, scooters, and all-terrain vehicles. The Service Manual used by your authorized dealer is available from your Honda dealer or These Honda manuals are written for the Helm, Inc. professional technician. However, if you possess...
Honda. Your warranty coverage does not apply to the normal wear Coverage and deterioration associated with use of the motorcycle. Your new Honda is covered by the following warranties: Your warranty coverage is not voided if you Motorcycle Limited Warranty ●...
Page 120
If you believe you have a problem with your dealership or their designated representative. motorcycle, call the service department of your Honda dealer. Make an appointment for an inspection and diagnosis. You will be asked to authorize that inspection, and your dealer will return the results of the inspection.
● If you wish to contact Honda directly to comment on your experiences with your We will likely ask your Honda dealer to respond, motorcycle or with your dealer, please send or possibly acknowledge your comments your comments to the following address: directly.
Page 122
Protection Plan to extend almost all of your warranty coverage (USA only). Your Honda dealer can also supply information about, riding events, and information about safety training available in your local area, and the Honda Rider’s Club of America (USA only).
Highway Traffic Safety Administration Washington, DC 20590. (NHTSA) in addition to notifying You can also obtain other information American Honda Motor Co., Inc. about motor vehicle safety from: http://www.safercar.gov If NHTSA receives similar complaints, it may open an investigation, and if it finds...
*1 Including rider, passenger, all luggage, and accessories VT1300CTA *2 Includes the weight of the luggage and added accessories. 728 lb (330 kg) 395 lb (179 kg) VT1300CR/CRA Maximum weight capacity 388 lb (176 kg) VT1300CT/CTA Maximum luggage weight 33 lb (15 kg)
Page 125
API service label, SAE 10W-30, JASO T Rear 170/80-15M/C 77H engine oil 903 standard MA, Pro Honda GN4 4-stroke Tire type bias-ply, tubeless oil (USA & Canada) or Honda 4-stroke oil, or DUNLOP ELITE3 Front an equivalent motorcycle oil BRIDGESTONE L309 F Recommended After draining 3.7 US qt (3.5 liters)
Page 126
Specifications ■ Bulbs ■ Torque Specifications Headlight 12V-60/55W Air cleaner housing cover bolts 1.1 lbf·ft (1.5 N·m, 0.2 kgf·m) Brake/Taillight 12V-21/5W Engine oil drain bolt 22 lbf·ft (30 N·m, 3.1 kgf·m) Front turn signal lights 12V-21/5W x 2 Oil filter 19 lbf·ft (26 N·m, 2.7 kgf·m) Rear turn signal lights 12V-21W x 2...
Page 127
Information Record Engine No. Ignition Key No. Color Label & Code Owner’s Name Address City/State Phone Dealer’s Name Address City/State Phone Service Manager...