1. Manuals
  2. Brands
  3. McConnel Manuals
  4. Lawn and Garden Equipment
  5. Twose Series
  6. Instruction & parts manual

McConnel Twose Series Instruction & Parts Manual

Ballast roller 2.5 & 3.0m wheeled type
Hide thumbs Also See for Twose Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Twose Series
SWH 8 BALLAST ROLLER
SWR 10 BALLAST ROLLER
2.5 & 3.0M WHEELED TYPE
INSTRUCTION & PARTS MANUAL
Publication No: 5293
May 2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Twose Series and is the answer not in the manual?

Questions and answers

Related Manuals for McConnel Twose Series

Summary of Contents for McConnel Twose Series

  • Page 1 Twose Series SWH 8 BALLAST ROLLER SWR 10 BALLAST ROLLER 2.5 & 3.0M WHEELED TYPE INSTRUCTION & PARTS MANUAL Publication No: 5293 May 2016...
  • Page 2 VERIFICATION OF WARRANTY REGISTRATION DEALER WARRANTY INFORMATION & REGISTRATION VERIFICATION It is imperative that the selling dealer registers this machine with McConnel Limited before delivery to the end user – failure to do so may affect the validity of the machine warranty.

  • Page 3: Warranty Policy

    12 months, unless a different period is specified. 1.02. All spare parts supplied by McConnel Ltd and purchased by the end user are warranted to be free from defects in material and workmanship from the date of sale to the original purchaser for a period of 6 months.
  • Page 4 McConnel Ltd web site and confirms the registration to the purchaser by completing the confirmation form in the operator’s manual. 2.02. Any fault must be reported to an authorised McConnel Ltd dealer as soon as it occurs. Continued use of a machine, after a fault has occurred, can result in further component failure for which McConnel Ltd cannot be held liable.

  • Page 5: Declaration Of Conformity

    DECLARATION OF CONFORMITY Conforming to EU Machinery Directive 2006/42/EC McCONNEL LIMITED, Temeside Works, Ludlow, Shropshire SY8 1JL, UK Hereby declare that: The Product; Tractor Trailed Roller(s) Product Code; TWBR Serial No. & Date ………………………………… Type ………………………… Manufactured in; United Kingdom Complies with the required provisions of the Machinery Directive 2006/42/EC The machinery directive is supported by the following harmonized standards;...
  • Page 6 No responsibility will be accepted by McConnel Limited for any injury, damage or loss arising from the improper use or lack of maintenance of any machinery supplied...
  • Page 8 INDEX OPERATOR SECTION GENERAL ARRANGEMENT SPECIFICATIONS GENERAL INFORMATION SAFETY NOTES AND WARNINGS HEALTH AND SAFETY GENERAL INSTRUCTIONS OPERATING INSTRUCTIONS SAFETY WHEN ROLLING ROUTINE MAINTENANCE AND LAYING-UP NOTES PARTS SECTION MAINFRAME ASSEMBLY - SWH 8 MAINFRAME ASSEMBLY - SWR 10 DRUM ASSEMBLIES AXLE ASSEMBLY - SWH 8 AXLE ASSEMBLY - SWR 10 RAM ASSEMBLY...

  • Page 10: General Arrangement

    GENERAL ARRANGEMENT SWH 8 BALLAST ROLLER IN WORKING POSITION...
  • Page 11 GENERAL ARRANGEMENT SWR 10 BALLAST ROLLER IN WORKING POSITION SWR 10 BALLAST ROLLER IN TRANSPORT POSITION...

  • Page 12: Specifications

    SPECIFICATIONS SWH 8 SWR 10 Rolling Width 2.5M 3.0M Drum Diameter 0.76M 0.76M Number of Drums Drum Capacity (Per Drum) 567 Litres 675 Litres Machine Length Operating 3.5M 2.981M Transport 3.5M 5.550M Machine Width Operating 2.87M 4.42M Transport 2.87M 2.03M Machine Weight Without Ballast 1010 Kg...

  • Page 13: General Information

    Full address to which spares are to be sent. Method of delivery required. CAUTION:- Always insist on genuine and correct spare parts. NOTE:- Further copies of this handbook/manual can be obtained from:- McCONNEL LIMITED Temeside Works Ludlow Shropshire SY8 1ND Telephone: 01584 873131 Email: sales@mcconnel.com...

  • Page 14: Safety Notes And Warnings

    SAFETY NOTES AND WARNINGS Throughout the handbook the following sub headings are used to draw attention to various points of importance. This is to draw attention to very important instructions which MUST be followed precisely to avoid injury or death. CAUTION This is used to draw attention to instructions which MUST be followed to avoid damage to operator, machine, process or the environment.

  • Page 15: Health And Safety

    HEALTH AND SAFETY Never attempt to assemble, couple up, operate machinery until understand fully the functions, controls and safety precautions required, as shown in the operators manual. Always follow tractor safety operations and instructions VERY carefully. NEVER TAKE RISKS CAUTION. Be aware of warning and instruction decals on machine as care must be taken and instructions obeyed.
  • Page 16 Always be aware of your surroundings - and operate machinery accordingly. Beware of confined-tight areas, low height restrictions, buildings overhangs etc. Also drive and operate bearing in mind weather conditions such as sun, rain, ice, snow, wind etc. (Make allowances in all situations). CAUTION Never carry "passengers"...

  • Page 17: General Instructions

    GENERAL INSTRUCTIONS Before attaching any machine to a tractor make sure that implement is still standing firmly on good solid - level site as it will be, providing unit was previously parked correctly. -Check that any wheels are 'chocked' correctly and that supports/props are in position where necessary to prevent booms etc.
  • Page 18 OPERATING INSTRUCTIONS SWH 8 Machines To Change the Roller from ‘Transport’ to ‘In Work’ Position Set the tap on the ram to the ‘open’ position Raise the axle by retracting the hydraulic ram fully Close the tap on the ram To Change the Roller from ‘In Work’...
  • Page 19 SAFETY WHEN ROLLING Before starting work with any roller ensure that the bearings are properly greased and that all bolts and nuts are tight. Remember that a heavy roller will add to your momentum and will require a longer distance for stopping. Particular care will be needed on hilly or sidling ground.
  • Page 20 ROUTINE MAINTENANCE AND ‘LAYING-UP’ DAILY Check end float and adjust if necessary. WEEKLY Grease pivot points thoroughly. Check all bolts and nuts for tightness. ANNUALLY AND LAYING-UP Periodically (once a year should suffice) check the bearings or bushes, spacer and axle for wear;...
  • Page 21 NOTES...

  • Page 22: Parts List

    Direct access can be gained using the web address or QR code below. http://www.mcconnel.com/support/product-support/interactive-parts-database/ If an interactive search yields no results please contact our Parts Dept. for information. Tel: +44 (0)1584 873131 All enquiries for parts must be addressed to; McCONNEL LIMITED Temeside Works Ludlow Shropshire SY8 1ND Telephone: 01584 873131 Email: parts@mcconnel.com...

  • Page 23: Main Frame Assembly

    5293 MAINFRAME ASSEMBLY SWH 8...
  • Page 24 MAINFRAME ASSEMBLY 209.220 MAINFRAME MODULE - SWH 8 209.070 MAINFRAME 45429.01 SERIAL NUMBER PLATE 05.227.01 HAMMER DRIVE SCREW 209.073 SCRAPER BAR 05.291.23 BOLT 05.287.03 SELF LOCKING NUT 05.281.03 FLAT WASHER 209.050 05.291.18 BOLT 05.287.02 SELF LOCKING NUT...
  • Page 25 MAINFRAME ASSEMBLY SWR 10...
  • Page 26 MAINFRAME ASSEMBLY 209.210 MAINFRAME MODULE - SWR 10 209.031 MAINFRAME 45429.01 SERIAL NUMBER PLATE 05.227.01 HAMMER DRIVE SCREW 209.047 SCRAPER BLADE 05.281.05 FLAT WASHER 05.287.03 SELF LOCKING NUT 05.291.23 BOLT 209.041 MAIN DRAWBAR DRAWBAR – TRANSPORT 209.046 209.051 00.372.01 LINCH PIN 209.052 00.372.01 LINCH PIN...

  • Page 27: Drum Assembly

    DRUM ASSEMBLY...
  • Page 28 DRUM ASSEMBLY 209.223 DRUM ASSEMBLY MODULE – SWH 8 209.074 AXLE 209.071 DRUM T1698 PLUG (HOLLOW) 088.001 BLOCK WOODEN – MACHINED 209.062 CLAMP PLATE 05.292.39 BOLT 05.287.04 SELF-LOCKING NUT T7824 GREASE NIPPLE 088-023-B SPACER 088-023-C SPACER 209.214 DRUM ASSEMBLY MODULE - SWR 10 209.040 AXLE 209.043...

  • Page 29: Axle Assembly

    AXLE ASSEMBLY SWH 8...

  • Page 30: Wheel And Tyre

    AXLE ASSEMBLY AXLE ASSEMBLY MODULE – SWH 8 209.212 209.072 AXLE PIVOT FRAME 207.058 STUB AXLE ASSY 05.285.01 BOLT 05.287.06 NUT SELF LOCKING 209.053 05.287.02 NUT SELF LOCKING 05.291.18 BOLT 207.228 WHEEL AND TYRE MODULE T5718 WHEEL AND TYRE...
  • Page 31 AXLE ASSEMBLY SWR 10...
  • Page 32 AXLE ASSEMBLY AXLE ASSEMBLY MODULE – SWR 10 209.212 209.042 AXLE PIVOT FRAME 207.058 STUB AXLE ASSY 05.285.01 BOLT 05.287.06 NUT SELF LOCKING 209.053 05.287.02 NUT SELF LOCKING 05.291.18 BOLT 207.229 WHEEL AND TYRE MODULE T5718 WHEEL AND TYRE...
  • Page 33 RAM ASSEMBLY - AXLE SEAL KIT 46673.25...
  • Page 34 RAM ASSEMBLY - AXLE 209.211 RAM ASSEMBLY MODULE - SWH 8 & SWR 10 46673.01 RAM ASSEMBLY 05.953.01 GREASE NIPPLE 08.297.08 PLASTIC BUSH 03.290.04 BONDED SEAL 01.099.01 ADAPTOR 05.124.01 ADAPTOR VALVE – ISOLATING 08.200.01 02.714.01 ADAPTOR BSP SWIVEL 46673.25 SEAL KIT HYDRAULIC INSTALLATION MODULE –...
  • Page 35 TRANSFERS 1. T410184 2. T410185 3. T410201...
  • Page 36 TRANSFERS 209.201 TRANSFER MODULE - SWH 8 & SWR 10 TRANSFER – HI-LIGHTER T410184 TRANSFER – TWOSE T410185 TRANSFER – GREASE GUN T410201...
  • Page 38 McConnel Limited, Temeside Works, Ludlow, Shropshire SY8 1JL. England. Telephone: 01584 873131. Facsimile: 01584 876463. www.mcconnel.com...

This manual is also suitable for:

Twose swh 8Twose swr 10

Table of Contents