Advertisement
Available languages
Available languages
SAR-G2+ RELAY UNIT
SAFETY PRECAUTIONS
( )
*
-
Always disconnect the power supply
before making modifications to the devic
.
- The fitting and handling of these devices must be carried out by
- The wiring must run at least
40 cm away from any other wiring
.
- Do not overtighten the screws on the terminal block.
- Install the relay unit in a dry and protected location free from the risk of dripping or splashing water.
- Install the SAR-G2 relay unit and SAR-12/24 together with the FA-G2 power supply unit.
+
- Do not place in humid, dusty or smoky locations, or near sources of heat.
- Before connecting the system to the mains, check the connections.
- Always follow the instructions contained in this manual.
( )
CHARACTERISTICS
*
G2+
- Digital relay for the
system, allows the following operating modes:
Stairs light activation relay (necessary module SAR-12/24).
O
Golmar additional alternating lock release relay (necessary power supply unit TF-104).
O
- Necessary to configure operating mode of the SAR-G2 relay unit.
- Connects to the Bus
door
panel.
- Configuration DIP switch.
- Operating status LEDs.
- The maximum consumption of relay contacts will be:
- 12Vdc output to activate SAR-12/24 module in operating mode "stairs light activation".
- The SAR-G2+ relay unit counts as one element (monitor/telephone) in the installation.
OPERATING MODES
( )
*
Stairs light activation relay (necessary module SAR-12/24):
- This operating mode allows activation of the stairs light from the apartment. (Light operating
mode Set the
:
Dip 4
to
ON
and from the
switch of the SAR-G2+).
It will be activated by pressing the button located below the light con
the settings menu of the ART 4/ ART 4 LITE, in the main menu of the ART 7/ ART 7 LITE monitor,
by clicking on the icon of the ART 7W monitor displayed on the screen in the main menu or
pressing for 3 seconds the
button
of the
handset on the hook).
See user manual for monitor
Mains
100~240Vac
FA- 2
G +
Monitor Bus
2
SAR-G2+ configuration
SW1 dip
switch:
Light operating mode:
ON
Dip 4
to
ON.
1
2
3
4
Dip 1
to
Dip3 a OFF.
J
P1
jumper
:
Leave i the
n
pos. 2-3.
IMPORTANT:
For the description, installation, configuration and programming of the system, see the corresponding manual.
( )
*
For more information, see the "TSAR-G2 (cód. 5012
https://doc.golmar.es/search/manual/50122550
e.
authorised personnel
.
+
+
0,75
A to
24
Vcc (
18W / 1A
)
to
18Vca (18VA)
Dip1
to
Dip3
to
OFF n
i the configuration
i
displayed
on the screen in
ART 1
terminal/ T-ART telephone (in standby and
or terminal
installed in the apartment.
To stairs light
push button
2
2
( ) 1
220V
ac
/1.8A m x.
SAR-G2+
SAR-12/24
2
2
G2 access door panel
+
( ) 1
Neutral point of the power supply of the
stairs light is connected in series through
the relay contacts of the SAR-12/24.
2
+
2550
)" user manual.
2
SAR-G2+ RELAY UNIT
OPERATING MODES
( )
*
Additional lock release activation relay (necessary power supply unit TF-104):
- This operating mode allows activation of a Golmar additional alternating lock release. This lock release is
.
activated as lock release 1 or lock release 2 and with the panel that has been assigned (through
configuration in SAR-G2
It will be activated by pressing the button located below
lock release 2 respectively
on the
corresponding
of the
ART1
apartment.
( ) 1
The power supply of the lock release
is connected in series through the
SAR-G2 relay contacts.
+
SAR-
G2 configuration
+
Lock release operating mode: Dip 4 to OFF.
Lock release 1 (door panel 1) operating mode:
ON
Door panel 1: Dip 1 & 2 to OFF.
Lock release 1: Dip 3 to OFF.
1
2
3
4
.
Lock release 2 (door panel 1) operating mode:
ON
Door panel 1: Dip 1 & 2 to OFF.
Lock release : Dip 3 to ON.
1
2
3
4
J
P1
jumper
:
Leave i the
IMPORTANT: Must be configured in the SAR-G2+ the lock release (1 or 2) that is not being used on door panel.
For the description, installation, configuration and programming of the system, see the corresponding manual.
( )
DESCRIPTION OF SAR-G2 RELAY UNIT
*
SW1 dip
-
NC
C NA 12+
12258965
V02
RELE SAR-G2+
CONTACTOS RELÉ /
RELAY CONTACTS
POWER
1A 18V AC
0.75A 24V DC
GOLMAR S.A.
C/ Silici, 13
08940-SPAIN
a
( )
*
INSTALLATION
( )
*
Description modes
( )
*
For more information, see the "TSAR-G2 (cód. 5012
https://doc.golmar.es/search/manual/50122550
+,
see
"TSAR-G2+ "
manual
) during a call or communication process.
of corresponding icon
) shown on the
ART4/
ART4 LITE/
ART7
icon of the ART 7W monitor displayed on the screen o
terminal / T-ART telephone Note:
.
See user manual for monitor
Additional
Va
Mains
lock release
100~240Vac
FA- 2
G +
Monitor Bus
SW1 dip
switch
:
2
2
n
pos. 2-3.
+
a
b
-
AP1
c
JP1
3
2
1
BUS BUS
d
e
h
f
g
-
-
NC
C NA 12+
AP1
12258965
V02
RELE SAR-G2+
JP1
3
CONTACTOS RELÉ /
2
RELAY CONTACTS
POWER
1
1A 18V AC
0.75A 24V DC
BUS BUS
GOLMAR S.A.
C/ Silici, 13
08940-SPAIN
and
configuration
SW1 dip
switch
+
2550
3
or
(
lock release 1 or
1
2
/ ART7 LITE monitor screen,
by clicking
r pressing the
button
or
or terminal
installed in the
c
( ) 1
2
2
SAR-G2+
TF-104
TF-104
Mains
2
100~240Vac
2
G2 Access
+
door panel
2
a.
12Vdc and AP output connector
1
.
b.
Relay contact connector.
c.
Label.
d.
JP
jumper
(do not use)
.
e.
Status LED (power supply).
f.
Configuration SW1 dip switch.
g.
Connector G2+
(
BUS)
.
h.
DIN rail latch release.
The relay unit can be mounted onto a DIN rail
(4 elements) by applying slight pressure.
To remove the relay unit from the rail, use a flat
screwdriver and lever it off, as shown in the
drawing.
DIN 46277
.
)" user manual.
Advertisement
