The installation and handling of this equipment must be performed by authorised personnel. O Install or modify the equipment without the power connected. Do not overtighten the screws on the terminal block of the SU-R5 relay unit. The entire installation must be at least 40 cm away from any other wiring.
The entire installation must be at least 40 cm away from any other wiring O Install the SU-R5 relay unit in a dry and protected place without risk of drip or water. projections. O Avoid to place it near to heating sources, in dusty locations or smoky enviroments.
SU-R5 relay unit. O If more than one SU-R5 relay unit is fitted (up to 4 in cascade), it is possible to monitor the visitor through the doors of the building. By pressing the...
Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18. Tekna SU-R5 monitors/telephones M =Master.
Page 6
Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18. Tekna SU-R5 monitors/telephones M =Master.
Page 7
Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18. Tekna SU-R5 monitors/telephones M =Master.
If there are (slave) access door panels, they will have their own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 19-22.
Page 9
If there are (slave) access door panels, they will have their own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 19-22.
The Stadio door panel with EL502 module to connect the AC lock release will have its own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18.
Page 11
The Stadio door panel with EL502 module to connect the AC lock release will have its own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18.
Page 12
The Stadio door panel with EL502 module to connect the AC lock release will have its own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 17-18.
If there are (slave) access door panels, they will have their own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 19-22.
If there are (slave) access door panels, they will have their own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. Installation diagrams on pages 19-22.
Power supply input. INSTALLATION etail of the installation of the SU-R5 relay unit. Install the relay unit in a dry and protected place without risk of drip or water projections. To avoid damage, the relay unit must be firmly fixed.
CONFIGURATION escription of the configuration dip switch. The Sw1 configuration DIP switch is located at the top of the module Relay unit timed door release: (from the monitor or AP of the unit itself): " " Dip switches : 1 and 2 OFF (3 seconds), 1 OFF and 2 ON (6 seconds) 1 ON and 2 OFF (9 seconds), 1 and 2 ON (12 seconds).
AC lock release If the lock release connected to the SU-R5 relay unit is AC, use a TF-104 transformer and connect the lock release as per the following diagram.
INSTALLATION DIAGRAMS 1st floor To the following distributor Tekna R5 SU-R5 T530/R5 SU-R5 R. Line D4L-R5R Vout Distribution box Remove the JP1 jumper from all of the distributors SU-R5 Relay Unit except the last. FA-Plus/C OUTPUT 18Vdc INPUT CAMERA LOCK RELEASE...
Page 19
The Stadio door panel with the EL502 module to connect the AC lock release will have its own power supply unit. Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the SU-R5 relay unit, never between the door panel and the relay unit. Vista Nexa Panel FA-PLUS/C rev.
INSTALLATION DIAGRAMS M =Master. S =Slave. SU-R5 Relay Unit FA-PLUS/C (1) (1) Address 1 rev. 938072 OUTPUT 18Vdc INPUT CAMERA LOCK RELEASE 110 0 AP AP V M +12 2nd Camera Mains Vc.c Vista Nexa Panel (1) (1) FA-PLUS/C rev. 938072...
Page 21
'1', 2nd the unit with address '2', 3rd the unit with address '3' and 4th the unit with address "4"). Note: The CD-Plus/R5 converter for porter's exchange, distributors, monitors and telephones should be connected to the output of the last SU-R5 relay unit, never between the door panel and the relay unit. SU-R5 Relay Unit...
Page 22
INSTALLATION DIAGRAMS Continued from previous page M =Master. S =Slave. SU-R5 Relay Unit FA-PLUS/C (1) (1) Address 3 rev. 938072 OUTPUT 18Vdc INPUT CAMERA LOCK RELEASE 110 0 AP AP V M +12 2nd Camera Mains Vc.c Vista Nexa Panel...
Page 23
1st floor To the following distributor Tekna R5 SU-R5 T530/R5 SU-R5 R. Line D4L-R5R Vout Distribution box Remove the JP1 jumper from all of the distributors except the last. SU-R5 Relay Unit FA-PLUS/C Address 4 rev. 938072 OUTPUT 18Vdc INPUT...
Page 24
Golmar se reserva el derecho a cualquier modificación sin previo aviso. Golmar se réserve le droit de toute modification sans préavis. Golmar reserves the right to make any modifications without prior notice.