Korenix JetCon 1302 Series Quick Installation Manual

A Beijer Electronics Group Company
JetCon 1302 Series Industrial Media Converter
Quick Installation Guide V1.2
Overview
JetCon 1302 Industrial Media Converter, conforming IEEE 802.3 and 802.3u standard,
supports 2 10/100Base TX plus one 100FX Ethernet port. JetCon 1302 adopts slim industrial
design to save rail space of compact system requirement. In order to survive under harsh
environment, JetCon 1302 chooses industrial-grade aluminum case with IP30 standard
protection. It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetCon 1302 is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
Package Check List
 JetCon 1302 Industrial Media Converter
 Quick Installation Guide
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 1302 on the DIN rail
Grounding JetCon 1302
ere is one grounding screw on the bottom side
of JetCon1302. Connect the frame grounding of
JetCon1302 to the grounding surface to ensure
safety and prevent noise.
Wiring the Power Inputs
1. Insert the positive and negative wires into the V+
Fault
and V- contact on the terminal block connector.
2. Tighten the wire-clamp screws to prevent the DC
wires from being loosened.
Notes: The recommended working voltage is DC24V
(DC18~ 32 V).
Wiring the Relay Output
e relay output alarm contacts are in the middle of
Fault
the terminal block connector as shown in the gure .
By inserting the wires and set the DIP switch of Port
Alarm to "ON", relay output alarm will detect any
port failures, and form a short circuit. e alarm
relay output is "Normal Open".
Connecting to Network
1. Connecting the Ethernet Ports: Connect one end of an Ethernet cable into the UTP port
of JetCon 1302, while the other end is connected to the attached networking device. All
UTP ports support auto MDI/MDIX function.
10M Ethernet or Green for 100M Ethernet.
2. Connecting the Fiber Port: Connect the ber port on your JetCon 1302 to another Fiber
Ethernet device, by following the gure below. Wrong connection will cause the ber port
not working properly.
ATTENTION
is is a Class 1 Laser/LED product.
！ Don't look into the Laser/LED Beam.
A Beijer Electronics Group Company
JetCon 1302 Series Industrial Media Converter
Quick Installation Guide V1.2
Overview
JetCon 1302 Industrial Media Converter, conforming IEEE 802.3 and 802.3u standard,
supports 2 10/100Base TX plus one 100FX Ethernet port. JetCon 1302 adopts slim industrial
DIP Switch Settings for Alarm Relay Output
design to save rail space of compact system requirement. In order to survive under harsh
environment, JetCon 1302 chooses industrial-grade aluminum case with IP30 standard
protection. It provides one relay output to alarm port break events, which is enabled/ disabled
by the dip switch. JetCon 1302 is recommended to be powered by DC24V (18~32V) from
the 2-pin terminal block.
A Beijer Electronics Group Company
Package Check List Overview JetCon 2301 Industrial Fast Ethernet to Fiber Media Converter Quick Installation Guide V1.1
JetCon 2301 is a single port Fast Ethernet to Fiber media converter, supporting 4 types of Converter with auto-change modes. forwarding modes – Store and Forward, Modi ed Cut-through, Pure Converter and e JetCon 2301 adopts rugged aluminum case with
 JetCon 1302 Industrial Media Converter environments with severe electromagnetic interference and -25~70°C (JetCon 2301) or IP31 grade enclosure and 1.5KV Hi-Pot isolation protection to operate in harsh
for alerting remote or central management systems when a remote fault occurs. It also -40~75°C (JetCon 2301-w). It features Link Loss Forwarding to forward link status changes adopts one relay output to alarm users if a port link fails or if the power fails. Alarms can be
DC10~60V through the 6-pin removable terminal block. enabled/ disabled by dip switch. JetCon 2301 has redundant power inputs with wide range e ber port supports
 Quick Installation Guide JetCon 2301 Industrial Media Converter  Package Check List Single-mode or Multi-mode for providing up to 30KM extended distance transmission. Pin No. # Status Description
 Quick Installation Guide
Installation
Mount the unit
Din-Rail mount: Mount the din-rail clip screwed on the rear of
JetCon 1302 on the DIN rail
ON To enable port break alarm at this port.
P1 to P3
(Pin1 ~3)
Off To disable port break alarm at this port.
Support
5 Years Warranty
Each of Korenix's product line is designed, produced, and tested with high industrial standard.
Port Alarm Fault V+ V- DC24
Korenix warrants that the Product(s) shall be free from defects in materials and workmanship
Erdung
for a period of ve (5) years from the date of delivery provided that the Product was properly
installed and used.
is warranty is voided if defects, malfunctions or failures of the warranted Product are caused
V+ V-
by damage resulting from force measure (such as oods, re, etc.), other external forces such as
Power Inputs
power disturbances, over spec power input, or incorrect cabling; or the warranted Product is
misused, abused, or operated, altered and repaired in an unauthorized or improper way.
Attention! To avoid system damage caused by sparks, please DO NOT plug in power
connector when power is on.
e product is in compliance with Directive 2002/95/EC and 2011/65/EU of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain
V+ V- hazardous substances in electrical and electronics equipment(RoHS Directives & RoHS 2.0).
Korenix Customer Service
Relay Output,
KoreCARE is Korenix Technology's global service center, where our professional sta s are
Carry ability
1A @24V
ready to solve your problems at any time Korenix global service center's e-mail is
KoreCARE@korenix.com.
For more information and documents download please visit our website:
http://www.korenix.com/downloads.htm
e LNK / ACT LED will turn Yellow for
RX RX
TX TX
Cable Wiring(SC to SC)
TX A RX B
RX A TX B
Alarm Switch
1 2 3