Download Print this page

Advertisement

Quick Links

Temporarily Repairing a Flat Tire
If the tire has a large cut or is otherwise severely damaged, you will need to have the
vehicle towed. If the tire only has a small puncture, from a nail for instance, you can
use the temporary tire repair kit so that you can drive to the nearest service station
for a more permanent repair.
If a tire goes flat while driving, grasp the steering wheel firmly, and brake gradually
to reduce speed. Then, stop in a safe place.
1. Park the vehicle on a firm, level, and non-slippery surface, and apply the parking
brake.
2. Put the transmission into
(
P .
3. Turn on the hazard warning lights and set the power mode to VEHICLE OFF
(LOCK).
uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire
1Temporarily Repairing a Flat Tire
The kit should not be used in the following situations.
Instead, contact a dealer or roadside assistance to
have the vehicle towed.
The tire sealant has expired.
More than one tire is punctured.
The puncture or cut is larger than 3/16 inch (4 mm).
The tire side wall is damaged or the puncture is
outside the contact area.
When the puncture is:
Smaller than 3/16 inch
Contact
Area
Larger than 3/16 inch
Damage has been caused by driving with the tires
extremely under inflated.
The tire bead is no longer seated.
The rim is damaged.
Do not remove a nail or screw that punctured the
tire. If you remove it from the tire, you may not be
able to repair the puncture using the kit.
Continued
Use Kit
Yes
(4 mm)
No
(4 mm)

Advertisement

loading

Summary of Contents for Honda Insight 2022

  • Page 1 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire Temporarily Repairing a Flat Tire If the tire has a large cut or is otherwise severely damaged, you will need to have the 1Temporarily Repairing a Flat Tire vehicle towed. If the tire only has a small puncture, from a nail for instance, you can The kit should not be used in the following situations.
  • Page 2 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire ■ 1Getting Ready to Temporarily Repair the Flat Tire Getting Ready to Temporarily Repair the Flat Tire Repair notification label and speed restriction label are applied to the side of the temporary tire repair kit. Power Plug When making a temporary repair, carefully read the instruction manual provided with the kit.
  • Page 3 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 1. Open the trunk floor lid. 2. Take the kit out of the case. 3. Place the kit face up, on flat ground near the flat tire, and away from traffic. Do not place the kit on its side.
  • Page 4 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire ■ 1Injecting Sealant and Air Injecting Sealant and Air CAUTION 1. Remove the valve cap from the tire valve Valve Cap stem. Tire sealant contains substances that are harmful if inhaled, ingested or if contact is made with the eyes or skin.
  • Page 5 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 4. Plug in the compressor to the accessory 1Injecting Sealant and Air power socket. WARNING Be careful not to pinch the cord in a door or window. Running the engine with the vehicle in an 5.
  • Page 6 Models with 215/55R16 93V tires See a Honda dealer for a replacement sealant bottle After the air pressure reaches front: 35 psi and proper disposal of an empty bottle. (240 kPa)/rear: 33 psi (230 kPa), turn off the kit.
  • Page 7 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 11. Press the pressure relief button until the gauge returns 0 psi (0 kPa). Pressure Relief Button 12. Apply the repair notification label to the Repair Notification Label flat surface of the wheel. The wheel surface must be clean to ensure the label adheres properly.
  • Page 8 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire ■ Distributing the Sealant in the Tire 1. Apply the speed restriction label to the location as shown. 2. Drive the vehicle for about 10 minutes. Do not exceed 50 mph (80 km/h). 3.
  • Page 9 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 5. Turn the selector knob to AIR. Do not turn the air compressor on to check the pressure. 2 Inflating an Under-inflated Tire P. 558 6. If the air pressure is •...
  • Page 10 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire Models with 215/55R16 93V tires 1Distributing the Sealant in the Tire • Greater than 25 psi (175 kPa), but less WARNING than front: 35 psi (240 kPa)/rear: 33 psi (230 kPa): Running the engine with the vehicle in an Turn the air compressor on to inflate the enclosed or even partly enclosed area can...
  • Page 11 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 8. Press the pressure relief button until the gauge returns to 0 psi (0 kPa). 9. Repackage and properly stow the kit. Pressure Relief Button Continued...
  • Page 12 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire ■ 1Inflating an Under-inflated Tire Inflating an Under-inflated Tire WARNING You can use the kit to inflate a non-punctured, under-inflated tire. 1. Open the trunk floor lid. Sealant/Air Hose Running the engine with the vehicle in an 2 Getting Ready to Temporarily Repair enclosed or even partly enclosed area can the Flat Tire P.
  • Page 13 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 7. Plug in the kit to the accessory power socket. Be careful not to pinch the cord in a door or window. 8. Turn the power system on. Keep the power system on while injecting air.
  • Page 14 uuIf a Tire Goes FlatuTemporarily Repairing a Flat Tire 12. Turn off the kit. Check the pressure gauge on the air compressor. If overinflated, press the pressure relief button. 13. Unplug the kit from the accessory power socket. 14. Unscrew the sealant/air hose from the tire Pressure Relief Button valve stem.