Subscribe to Our Youtube Channel
Related Manuals for InWin RS316-07
Summary of Contents for InWin RS316-07
- Page 1 HYBRID BACKPLANE with EXPANDER User Manual P/N : 2RAKVI007700 Model：RS316-07 HYBRID EXP-BP(OCULINK) MODULE (BROADCOM COBRA BASED) Version : A0 Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 1 OF 23...
-
Page 2: Table Of Contents
Expander Chipset SAS3X36R Firmware Upgrade Description ........... 17 Out-Of-Band through serial console ..................17 M058 Micro-controller Firmware Upgrade Description ............19 Management ....................22 Useful Console Commands ....................22 Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 2 OF 23... -
Page 3: Overview
Overview InWin’s 12G SAS3 Backplanes equipped with Broadcom 3X36R Expander provide an industry leading high performance and high stability of data transfer for storage server solution. The backplanes support state-of-the art SAS3 12Gbps HDD/SSD and also backward compatible with SAS 6Gbps, SATA 6Gps and SATA 3Gps HDD/SSD. The backplane has 8 * OcuLink (SFF-8621) connectors and 8* U.2 (SFF-8639) connectors to accommodate 8 * 2.5”NVMe SSDs... -
Page 4: Physical Outlook
Physical Outlook BOTTOM VIEW TOP VIEW Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 4 OF 23... -
Page 5: Mechanical
Mechanical Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 5 OF 23... -
Page 6: Connectors And Components
Main Power Connector ：PW1/2,PW3/4 I2C External Header: JC1/JC2 FAN Connector : FAN1~FAN4 Buzzer: SUB1 M/B Fan Speed Control : JM1 SAS3x36R Expander chip : U1 Connector Pin Definitions. CN1/CN2/CN3 NVME1~NVME8 Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 6 OF 23... -
Page 7: Connector Pin Definitions
PIN # Definition Communication BUS to Host I2C_CLK (Preserved) I2C_DAT Ground Firmware Programming Connector PIN # Definition PIN # Definition SDB_TX +1.8V SDB_RX Ground UART_TX UART_RX Ground Ground +3.3V Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 7 OF 23... - Page 8 JD1/JD2 Firmware Programming Connector PIN # Definition PIN No# Definition ICE_CLK ICE_DATA #Key ICE_RST Ground M/B FSC 3-Pin Connector PIN # Definition MB_PWM BP_TACH Ground DISK1/5/9/13,DISK4/8/12/16 DISK2/3/6/7,DISK10/11/14/15 Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 8 OF 23...
-
Page 9: Connector Locations And Led Indicators
LED1~4 DISK1~DISK4 Activity/Failure LED DG5~DG8 DISK5~DISK8 Power LED LED5~8 DISK5~DISK8 Activity/Failure LED DG9~DG12 DISK9~DISK12 Power LED LED9~12 DISK9~DISK12 Activity/Failure LED DG13~DG16 DISK13~DISK16 Power LED LED13~16 DISK13~DISK16 Activity/Failure LED Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 9 OF 23... -
Page 10: Hardware Specification
DBG/UART (JC3) Use for firmware upgrade and debugging purpose. JD1/JD2 Header for Programming MCU Firmware. JM1 connector for Fan speed control connected between Motherboard and backplane. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 10 OF 23... -
Page 11: Led Behavior
When SGPIO Jumper setting is enabled the LEDs behave according to the SGPIO signals. When SGPIO is disabled, the RED LEDs (for Locate and Fail) do not behave while the Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 11 OF 23... - Page 12 NVMe disks. For example, NVMe1 and NVMe2 LED management signal is form NVMe1 connector’s sideband I2C bus, NVMe3 and NVMe4 LED management signal is from NVMe3 connector’s sideband I2C bus and …etc. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 12 OF 23...
- Page 13 : 50% On and then Off in a one second circle Slow_Blink_1 : 50% On and then Off in a 2 seconds circle ActFlash : Stay off while idle and fast flash upon I/O load Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 13 OF 23...
-
Page 14: System Alarm
1 short beep stands for Fan Fails 2 short beeps stand for Over-Temperature Press Mute Button to disable buzzer beeps and will be retriggered when either system error occurs again. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 14 OF 23... -
Page 15: Smart Fan Control
6. When an external PWM source joins, the output PWM duty is determined by comparing the internal calculated PWM and external PWM and then select whichever is higher as the output PWM to the fan modules. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 15 OF 23... - Page 16 Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 16 OF 23...
-
Page 17: Firmware Upgrade
Please note that the connector to Backplane varies depends on the backplane. The 07 series backplane UART port is redesigned with smaller form factor. 2. Require a host with a serial COM port. 3. Connect serial cable between Backplane and host. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 17 OF 23... - Page 18 4. Configure serial port setting as 115200, N, 8, 1. 5. Command “fdl 0 0 y” for system firmware upgrade in serial console. Sending system firmware through Xmodem. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 18 OF 23...
-
Page 19: M058 Micro-Controller Firmware Upgrade Description
Fan speed control and system fail alarm. These MCUs are preprogrammed in manufacturing. In most cases, the MCUs are not required to reprogram unless there is issue needed to fix. How to upgrade firmware? Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 19 OF 23... - Page 20 1. Require Nuvoton ARM Cortex-M0 programming tool. Nu-Me or Nu-Link and install Nuvoton ICP Programming tool software. 2. Connect Nu-Link USB end to a host and the SWD end to Backplane ICE connector for each MCU. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 20 OF 23...
- Page 21 3. Make sure device is connected and select the binary file being programmed and then click on Start button to program firmware. 4. Please refer to http://www.nuvoton.com/resource- files/NuLink_Adapter_User_Manual_EN_V1.01.pdf for more details. Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 21 OF 23...
-
Page 22: Management
- 'config' subcommand displays phy event configuration - 'event' subcommand displays phy event counters - 'reset' subcommand resets all phy counters Display expander sasaddr [-d] Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 22 OF 23... - Page 23 SAS address ('-d': also show virtural ports address) Show POST info showpost Show MFG revision showmfg Show firmware revision Model : RS316-07 Hybrid EXP-BP (COBRA) User’s Manual PAGE 23 OF 23...
Need help?
Do you have a question about the RS316-07 and is the answer not in the manual?
Questions and answers