Table of Contents
Advertisement
Engineers Forms
Commissioning/Field settings record sheet (continued from the previous page)
Main remote controller screen
Service menu Operation
settings
Energy
monitor
settings
External in-
put settings
Thermo ON output
*1 The settings related to Zone2 can be switched only when 2-zone temperature control or 2-zone valve ON/OFF control is active.
*2 The settings related to Zone2 can be switched only when 2 Zone temperature control is enabled (when DIP SW2-6 and SW 2-7 are ON).
*3 Cooling mode settings are available for ERS* model only.
*4 Only available if DHW tank present in system.
*5 When the hydrobox is connected with a PUMY-P outdoor unit, the mode is fixed to "Normal".
*6 For the model without both booster and immersion heater, it may not reach the set temperature depending on the outside ambient temperature.
*7 This setting is valid for only cylinder units.
*8 The lower limit is -15°C depending on the connected outdoor unit.
*9 The lower limit is -13°C depending on the connected outdoor unit.
*10 The lower limit is -14°C depending on the connected outdoor unit.
*11 On: the function is active; Off: the function is inactive.
*12 Do not change the setting since it is set according to the specification of flow sensor attached to the hydrobox.
*13 When DIP SW1-1 is set to OFF "WITHOUT Boiler" or SW2-6 is set to OFF "WITHOUT Mixing tank", neither Boiler nor Hybrid can be selected.
*14 Valid only when operating in Heating room temperature.
*15 When DIP SW5-2 is set to OFF, the function is active.
*16 If asterisk (**) is chosen freeze stat function is deactivated. (i.e. primary water freeze risk)
*17 When the hydrobox is connected with a PUMY-P outdoor unit, the mode is fixed to "Ambient".
*18 "*" of "*/kWh" represents currency unit (e.g. € or £ or the like)
*19 The default setting is 1 pulse/kWh depending on the connected indoor unit.
OCH712C
Smart grid ready
DHW
Heating
Cooling
Pump cycles
Floor dry up function
Summer mode
Water flow control
Electric heater
Booster heater
1 capacity
capacity
Booster heater
2 capacity
Immersion
heater capacity
Analog output
Delivered energy adjustment
Water pump input
Pump 1
Pump 2
Pump 3
Pump 4 *7
Electric energy meter *19
Heat meter *19
Demand control (IN4)
Outdoor thermostat (IN5)
83
Parameters
On/Off
Target temp(+1
to
+20°C) / -- (Non active)
On/Off
Target temp.
Switch-on recommendation (20
Switch-on command (20
On/Off
Target temp.
Switch-on recommendation (5
Switch-on command (5
Heating (On/Off)
Cooling (On/Off)
Interval (10
120 min)
to
On/Off *11
Target temp.
Start&Finish (20
to
Max. temp. (20
60°C)
to
Max. temp. period (1
Flow temp.
Temp. increase step (+1
(Increase)
Increase interval (1
Flow temp.
Temp. decrease step (−1
(Decrease)
Decrease interval (1
On/Off
Outdoor ambi-
Heating ON (4
to
19°C)
ent temp.
Heating OFF (5
20°C)
to
Judgement
Heating ON (1
48 hours)
to
time
Heating OFF (1
48 hours)
to
Forced heating ON (-30
to
10°C)
On/Off
0
30 kW
to
0
to
30 kW
0
to
30 kW
0
to
30 kW
−50
+50%
to
0
200 W or ***(factory fitted pump)
to
0
200 W
to
0
200 W
to
0
to
200 W
0.1/1/10/100/1000 pulse/kWh
0.1/1/10/100/1000 pulse/kWh
Heat source OFF/Boiler operation
Heater operation/Boiler operation
Zone1/Zone2/Zone1&2
Default
Field
setting
setting
Off
--
Off
60°C) 50°C
to
to
60°C)
55°C
Off
to
25°C)
15°C
25°C)
10°C
to
On
On
10 min
Off
60°C)
30°C
45°C
to
20 days)
5 days
+10°C) +5°C
to
7 days)
2 days
to
−10°C) −5°C
to
to
7 days)
2 days
Off
10°C
15°C
6 hours
6 hours
5 °C
Off
2 kW
4 kW
0 kW
0 kW
0%
***
0 W
0 W
72 W
1000 pulse/kWh
1000 pulse/kWh
Boiler
operation
Boiler
operation
Zone1&2
Notes
Hide quick links:
Advertisement
Table of Contents
