Advertisement
Quick Links
Item
Qty
Description
A
1
Winch Post
B
Non-Winch Post
1
C
1
Removable Winch Handle
D
1
PK10NXL Pickleball Net
Inspect all contents prior to installation. Report any missing parts to dealer immediately
Read all instructions before proceeding.
Lacing Bar
48"
8"
FIGURE 1
Date: 11/7/2018
Rev: 1
—— Instruction Manual ——
PK10XL
Competition Pickleball System
1.
Use the attached court diagram to determine where to locate and dig two
8" round and 48" deep holes 22 feet apart. See Figure 1.
2.
Insert Winch (A) and Non-Winch (B) posts into the holes with the lacing
bars facing the pickleball court and fill holes with concrete. Each hole will
require between 6 and 8 1/3 cubic foot bag of concrete. Make sure to brace
posts while concrete is curing to maintain the 36 1/2" dimension and ensure
the post remain perpendicular to the court surface. See Figure 1.
3.
Dig one 8" round and a minimum 12" deep hole centered between the
two pickleball posts (make sure to bell out the bottom of the hole). Insert
TNCSA Center Strap Anchor (F) with the strap retaining bar running
parallel with the PK10NXL Net (D) and fill hole with concrete. The hole
36 1/2"
will require 2 to 3 1/3 cubic bags of concrete. See Figure 2.
4.
Concrete must cure 7-10 days before continuing with PK10NXL Pickleball
Net (D) installation.
5.
Stretch out PK10NXL Pickleball Net (D) across the court.
Use models PK23 or PK235 (H) for removable post installation. Use
instructions provided with these sockets for installation procedure.
6.
Hook the loop on the PK10NXL Pickleball Net (D) top cable around the
net retaining pin on Non-Winch Post (B) and over the top pulley.
See Figure 3.
7.
Cut off loop and remove 12" of nylon cable coating from the top net
cable, insert cable into the winch cable hole on the Winch Post (A). Use
the Removable Winch Handle (C) to crank cable until you achieve 34" at
the center of PK10NXL Pickleball Net (D). See Figure 4.
B.A.
N.J.C.
P A R T S L I S T
Item
Qty
E
1
F
1
G
2
H
2
Note:
File: \pub\pk10xl
1
Description
TN10CS Center Court Hold Down Strap
TNCSA Center Strap Anchor
Lacing Cord
PK23 or PK235 Socket (Optional)
.
Ref#: 960921
Advertisement
Related Manuals for Bison PK10XL
Summary of Contents for Bison PK10XL
- Page 1 Winch Post (A). Use the Removable Winch Handle (C) to crank cable until you achieve 34” at 8" the center of PK10NXL Pickleball Net (D). See Figure 4. FIGURE 1 Date: 11/7/2018 Rev: 1 B.A. N.J.C. File: \pub\pk10xl Ref#: 960921...
- Page 2 Insert dowels through the end side tapes of PK10NXL Pickleball Net (D). Square up PK10NXL Pickleball Net (D) to each post, use Lacing Cord (G) to secure PK10NXL Pickleball Net (D) to each post. See Figure 3. 10. Attach TN10CS Center Court Hold Down Strap (E) to the strap retaining bar in the TNCSA Center Strap Anchor (F).