Advertisement
Available languages
Available languages
Checking the working systems
This check is very important, and must be carried out conscientiously before you fly the model for the first
time. Start by giving all the batteries a full charge, including the transmitter battery. Assemble the model
completely, ready to fly. Important: switch the transmitter on first, and check that the stick or switch
which controls the electric motor is at the "OFF" position. It should now be safe to connect the
speed controller connector to the LiPo flight pack. From this point on, all work on the model must
be carried out from behind the propeller.
Ask a friend to hold the model for you, and check that the speed control function operates correctly. Test
the aircraft's control surfaces again with the motor running. When you are confident that all is well, switch
the motor off and disconnect the LiPo battery from the speed controller.
Test-flying
For the model's first flight, seek out a large flying field devoid of all obstacles. If possible, wait for a day
with little or no breeze. If there is detectable air movement, always launch directly into wind. Set the
motor to full speed, and give the model a powerful hand-launch, with the wings and fuselage level.
Allow the machine to climb to a safe height, then switch off the motor and check the pitch trim; you may
find that slight elevator trim correction is necessary on the glide. Always land the model into wind with the
motor stopped. As soon as you reach the model, disconnect the speed controller from the LiPo battery.
General information on flying the MAXIE SPORT
Allow the LiPo battery and the electric motor to cool down to ambient temperature after each flight.
Never overcharge the LiPo battery. These packs are supplied with comprehensive instructions regarding
safety and proper charging, and these must be observed at all times.
If, for whatever reason, the propeller should touch the ground and stop - perhaps if you have to abort a
launch - switch off the electric motor immediately.
Always remove the LiPo battery from the MAXIE SPORT before transporting and storing the model.
Store the LiPo battery only in the discharged state. We recommend that you store these batteries in a
safety case, Order No. 8371.
Parts List
Part
Description
No.
1
Reinforcing strip
2
Decal
3
Servo well cover retainer
4
Fuselage
5
Motor bulkhead
6
Battery support
7
Cheese-head screw
8
Washer
9
Motor bulkhead, small
10
Canopy
11
Canopy locating peg
12
Canopy latch
13
Fuselage cross-piece
14
Captive nut
15
Countersunk screw
16
Wing saddle tape
17
Heat-shrink sleeve
18
Clevis
19
Threaded pushrod
20
Tail post
21
Hinge doubler
22
Hinge doubler
23
Point-hinge
24
Rudder
25
Control surface horn
26
Tailplane
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten!
No.
Material
off
4
Self-adhesive film
4
Self-adhesive film
2
Self-adhesive film
1
GRP
1
Plywood
1
Plywood
2
Steel
2
Steel
1
Plywood
1
ABS
1
Steel
1
Brass
1
Plywood
2
Steel
2
Plastic
2
Foam
2
Plastic
8
Plastic
4
Steel
1
Plywood
1
Plywood
1
Plywood
2
Plastic
1
Balsa
4
Plastic
1
Balsa
Dimensions
240 x 60 x 0.1
120 x 40 x 0.1
113 x 65 x 0.1
Ready made
Laser-cut, 3
Laser-cut, 3
M3 x 10
6 / 3.2 Ø
Laser-cut, 3
Ready made
2 Ø x 50
Ready made
Laser-cut, 3
M5
M5 x 40
250 x 9 x 1.6
40 x 40
Ready made
M2 x 30 screw
Laser-cut, 3
Laser-cut, 3
Laser-cut, 3
Ready made
Ready made
Ready made
Ready made
25
09/2006
Advertisement
