Related Manuals for Wallenstein BA201
Summary of Contents for Wallenstein BA201
- Page 1 INSTALLATION INSTRUCTIONS Backhoe Kit for LXT95 & LXT115 Log Grapple Booms Z97831_En Rev Sep-2021...
-
Page 2: Safety Alert Symbol
BA201 Safety Safety Alert Symbol This Safety Alert Symbol means: ATTENTION! BE ALERT! YOUR SAFETY IS INVOLVED! The Safety Alert Symbol identifies important safety messages on the machine and in this instruction. This symbol means be alert to the possibility of personal injury or death. Follow instructions provided. -
Page 3: Parts Breakdown
BA201 Parts Breakdown BA201 Backhoe Kit does not include a bucket. Bucket Item Part Number Description must be purchased separately. See table below for 3011C107 Cylinder, 2-1/4 x 12-7/8" Stroke bucket size options. SLK-2212 Seal Kit for 3011C107 Model Size 3011M109 Pin, 1 x 7.45 Greasable... -
Page 4: Installation Instructions
• Park the trailer on dry level ground, with the wheels chocked. Make sure the log grapple trailer and the area To install the BA201 Backhoe Kit and BK bucket on the LXT around it is clear and free of debris. - Page 5 BA201 Step 1 Step 3 • On the grapple pivot, remove the nut from the pivot pin. CAUTION! Gently drive the pin out of the pivot. Move the grapple pivot out of the boom nose. Risk of burns to exposed skin.
- Page 6 BA201 Step 5 • Install the bucket (purchased separately). Align the bucket main pivot to the dipper main pivot. • Position the 6089W250 chain hook (7) with the dipper main pivot. • Insert 3011W1170 flanged pin (6) through dipper, chain hook, and pivot.
-
Page 7: Operating Safety
BA201 Operating Safety • Extend stabilizers to support frame while excavating. • Keep the unit attached to the tow vehicle for extra stability. • Review the work site and plan the project before starting, WARNING! clearly marking the area to be excavated. - Page 8 Main boom rotate right–push the lever to the With the BA201 Backhoe Kit installed, bucket curl-in and right to rotate the main boom clockwise. curl-out is performed with the left-to-right grapple rotate control lever (4).
- Page 9 BA201 Digging with the Backhoe IMPORTANT! Do not use the side of the excavation to stop the bucket. The backhoe could be damaged. • Swing the dipper out and adjust bucket so the teeth can dig into the ground at a slight angle. Lower the boom down to set teeth into the ground.
-
Page 10: Transporting Safety
BA201 Transporting Trailer mount 1. Be sure the trailer is hitched positively to the vehicle and a IMPORTANT! LXT95 Log Loader / Trailer is not intended for retainer is used through the drawbar. use or transport on public roadways. Therefore, it does not 2. -
Page 11: Service Illustration
BA201 Service Illustration This illustration shows the location of service grease points for BA-201 and BK series buckets. BK-2612 bucket is shown, but grease points are the same for all BK series buckets. Grease pivot pins every 50 hours of operation. -
Page 12: Product Warranty
BA201 Product Warranty LIMITED WARRANTY Wallenstein products are warranted to be free of defects in materials and workmanship under normal use and service, for a period of Five Years for Consumer Use Two Years for Commercial/Rental Use from the date of purchase, when operated and maintained in accordance with the opera�ng and maintenance instruc�ons supplied with the unit. -
Page 13: Bolt Torque Specifications
BA201 Bolt Torque Specifications Checking Bolt Torque Imperial Bolt Torque Specifi cations The tables shown give correct torque values for various Torque Value bolts and capscrews. Tighten all bolts to the torque values Bolt specified in the table, unless indicated otherwise. Check SAE Gr. -
Page 14: Hydraulic Fitting Torque
BA201 Hydraulic Fitting Torque Hydraulic Fitting Torque Tightening Flare Type Tube Fittings Tube Size Flats From Size Torque value 1. Check flare and flare seat for defects that might Across Finger Tight cause leakage. Flats 2. Align tube with fitting before tightening. - Page 15 WallensteinEquipment.com...