Making Espresso; Making Cappuccino - Vitek VT-1501 Manual Instruction

•
Insert the coffee filter (4) into the holder (5),
matching the ledge on the filter (4) with the
slot on the holder (5) and turn the filter (4)
clockwise/counterclockwise.
•
Install the filter holder (5) into the coffee
maker. The holder (5) ledges should match
the grooves on the boiler «
turn the filter holder (5) handle (7) to the right
until bumping «
•
Place a suitable cup on the tray grid (8).
•
Insert the power plug into the mains socket.
•
Switch the coffee maker on, setting the
power switch (14) to the «–» position, the
indicator (1) will light up, and the indicator (2)
will start flashing.
•
Wait until the boiler heats up, the indicator (2)
will stop flashing and light constantly.
•
Set the operation mode switch knob (3) to
the position «
off in 30 seconds by setting the operation
mode switch (3) to the position « ».
•
Preheating is over.

MAKING ESPRESSO

Attention!
When making coffee do not leave the operat-
ing coffee maker unattended, as it is necessary
to watch the cup being filled with ready coffee!
•
Make sure that the power switch (14) is in
position «0», and the operation mode switch
knob (3) is in position « ».
•
To remove the tank (11), take it by the han-
dle (10) and remove the tank (11) upwards,
fill it with cold water up to the MAX mark and
install it back to its place.
•
To remove the filter holder (5) turn the han-
dle (7) to the left «
holder (5).
•
Put ground coffee in the filter (4) using the
measuring spoon (16), slightly tamp the
coffee with the back side of the measuring
spoon (16).
• Install the filter holder (5) into the coffee
maker. The holder (5) ledges should match
the grooves on the boiler «
turn the filter holder (5) handle (7) to the right
until bumping «
•
Place the cup on the tray grid (8).
•
Insert the power plug into the mains socket.
•
Switch the coffee maker on, setting the
power switch (14) to the «–» position, the
IM VT-1501.indd 5
», after that
».
», switch the water supply
» and remove the filter
», after that
».
indicator (1) will light up, and the indicator (2)
will start flashing.
•
Wait until the boiler heats up, the indicator (2)
will stop flashing and light constantly.
•
Switch the water supply on by setting the
operation mode switch knob (3) to the posi-
tion « », watch the cup being filled with
ready coffee.
•
To switch the water supply off, set the oper-
ation mode switch knob (3) to the position
« ».
Notes:
After you set the operation mode knob (3) to
–
the position « », the pressure is released,
the remaining hot water fills the tray (9);
you will hear a distinctive sound and see the
steam released from the tray grid (8), be
careful to avoid burns by the released hot
steam.
Control the tray (9) filling, periodically pour
–
out the liquid and wash the tray (9).
The pop-up indicator (15) shows the tray (9)
–
filling.
•
Switch the coffee maker off by setting the
power switch (14) to the position «0», the
indicator (1) will go out.
•
Wait until the coffee maker cools down and
remove the filter holder (5), turn the han-
dle (7) to the left «
coffee remnants and wash the filter (4).
Note:
The cups used need to be preheated; to do
–
this, place the cups on the upper tray, while
water is heated in the boiler, the upper tray
heats up too, thus warming the cups.

MAKING CAPPUCCINO

Attention! Be careful to avoid burns by the
released hot steam.
•
Make coffee, as described in the chapter
«MAKING ESPRESSO», in the cup with
enough capacity to add frothed milk or
cream.
•
Set the operation mode switch knob (3) to
the position « », wait until the indicator (2)
lights constantly.
•
Put the tip (13) into the cup with cold milk or
cream.
•
Set the operation mode switch knob (3) to
the position « ». The tip (13) should not
touch the bottom of the cup, as this can hin-
5
ENGLISH
». Remove the ground
20.05.2019 9:28:42