1. Manuals
  2. Brands
  3. Eclipse Manuals
  4. Paintball equipment
  5. GEO
  6. Operator's manual

Eclipse GEO Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Eclipse GEO

Summary of Contents for Eclipse GEO

  • Page 2 Geo. (OpErariOs) UsariOs EsTá EN iNglés. never look into the barrel or breech area of the Geo contiene importantes normas de observe all local and national laws, regulations and whilst the marker is switched on and able to fire.

  • Page 3: Warranty Card

    QUicK gUidE > UNdErsTaNdiNg ThE BaTTErY iNdicaTOr > dwEll -the dwell parameter names the component parts of the Geo marker. this information on the location of your nearest Geo > ThE gaME TiMEr > Fsd cOMp -the first shot drop-off...
  • Page 4 #016 nbr70 o-ring which prevents the barrel from vibrating loose from the Geo body when the marker is fired. there is also a EYE cOVEr scrEw an o-ring on the barrel front (#015 nbr70) helps with alignment between the barrel back and front.
  • Page 5 BOlT sYsTEM QUicK gUidE #15 NBr 90 CONTENTS WARNING ORIENTATION ORIENTATION warNiNg: dO NOT rEMOVE ThE iNliNE pUrgE cONTrOl ValVE. QUICK SET-UP USING YOUR GEO FailUrE TO cOMplY wiTh This warNiNg MaY caUsE ThE MarKEr TO FirE a prOp shaFT shOT ThaT cOUld rEsUlT iN sEriOUs iNJUrY Or dEaTh.

  • Page 6: Solenoid Assembly

    OpEraTiONal OVErViEw QUicK gUidE CONTENTS below is a brief overview of what happens spOOl pacK rETaiNiNg scrEw when you fire your Geo. the location of parts ORIENTATION ORIENTATION FilTEr discussed in the text below can be found on QUICK SET-UP page 78-79.
  • Page 7 QUICK SET-UP QUICK SET-UP At the rear of the Geo grip frame you will find the away and with the barrel pointing to the right. navigation console USING YOUR GEO (FigUrE 1.5)
  • Page 8 ‘double-clicking’ . the Geo can also be switched on by QUICK SET-UP QUICK SET-UP a paintball is ready to fire from the Geo. if no paintball is pushing and holding the button (FigUrE 3.1).
  • Page 9 MacrOliNE hOsiNg aNd QUicK gUidE ElBOws CONTENTS before you can begin to use your Geo, you will need to the Geo utilises a t-slot arrangement to mount the ORIENTATION attach an air-system and a paintball loader. oops to the bottom of the frame. the t-slot is an...
  • Page 10 Geo. once you have filled your loader and air tank you will then be ready to begin using your Geo.

  • Page 11: Setting The Trigger

    ThE TriggEr (cONTiNUEd) QUicK gUidE CONTENTS the Geo provides the user with the option to use is used to adjust the Micro switch activation screw ORIENTATION either a micro- switch or an opto sensor as the means point in the trigger pull at which the micro-switch is for detecting trigger pulls.

  • Page 12: User Interface

    Geo has a simple user interface through which ORIENTATION velocity at which your Geo is firing. this is done by all aspects of it’s electronic control system can be inserting a 1/8" hex key into the adjuster screw at the...
  • Page 13 Geo is configured to use the micro- it must first be released and then pulled. the trigger the Geo can be fired at a maximum rate of user has selected training mode. As the switch to detect trigger pulls. the micro-...

  • Page 14: Battery Level Indicator

    0.5 affects the way in which the Geo shoots, without the the screen represents the number of full to another menu. branches always have an animated MENU TREE seconds.
  • Page 15 ORIENTATION QUICK SET-UP MaiN MENU sET-Up MENU USING YOUR GEO MENU TREE MENU TREE OFF? turn off the Geo lOcK ADVANCED SET-UP turn the tournament lock off displaY MAINTENANCE turn the tournament lock on timer display the game timer on the run screen...
  • Page 16 CONTENTS ORIENTATION raMp sET* QUICK SET-UP FUll 1.0 - 20.0 time in milliseconds that a paintball must be in the breech for the Geo to be USING YOUR GEO TYpE step select step type ramping ready to fire MENU TREE...

  • Page 17: Altering Parameters

    ORIENTATION a parameter value on the right of the screen, pressing affect the way in which the Geo shoots and which this parameter is used to select the information that is QUICK SET-UP...
  • Page 18 Game timer to begin counting down. this timer counts down to a specific time set by the alarM USING YOUR GEO parameter can be set between 00:00 and 60:00 minutes parameter has the following choices: parameter. this parameter can be set between 00:00...

  • Page 19: The Setup Menu

    Geo operates. the Geo has a tournament lock which prevents the in order to simplify the set up of the Geo a number QUICK SET-UP to access this menu, first turn on the Geo and then user from making changes to any parameter that of preset configurations are available for selection.
  • Page 20 > Ms 08: load a set of parameters that rOF cap Max rOF MOdE or not the Geo should have a limited, or capped rate achievable rate of fire from the Geo. the value of this configures the Geo to comply with the USING YOUR GEO of fire.
  • Page 21 Geo rate of fire over rate of trigger pulls. > sTEp: step ramping will cause the Geo to shoot in MENU TREE 15.0 balls per second and should always be set to the...
  • Page 22 ORIENTATION the parameter sets the number of trigger pulls that are this parameter sets the minimum rate at which the once the Geo is ramping the user has to continue to parameter defines the amount of time QUICK SET-UP rEsTarT...
  • Page 23 ORIENTATION the lcd backlight is illuminated whenever any of the if the Geo is inactive for a period of time then it will the parameters on the timing menu all relate to the buttons are pressed on the Geo. the parameter automatically switch off in order to save power.
  • Page 24 QUICK SET-UP the Geo’s software filters which prevent the Geo from bounce that might occur in the Geo and can be set detect that the bolt is fully retracted and the breech is firing unless all of the necessary conditions are met. the between level 1 and level 9 in one level increments.
  • Page 25 USING YOUR GEO paintball has to be in the breech before the Geo is can be set between 1.0 and 20.0 milliseconds in 0.5 ms is adjustable between 51% and 99% in 1% increments.

  • Page 26: Basic Trigger

    ‘t’ to indicate that training mode is enabled. SPARES & ACCESSORIES note: the fAstest wAy to shoot A Geo is to wAlk the the training parameter choices are as follows:- triGGer with two or more finGers. feAtherinG (not...
  • Page 27 >caNcEl: TriggEr parameter unchanged. ThE TriggEr paraMETEr TONEs the Geo is fitted with a dual trigger pull detection system. A non-contact opto- ThE TONEs paraMETEr electronic trigger sensor arrangement is used to detect trigger movement this parameter sets the Geo emits a tone...
  • Page 28 (sEE FigUrE 9.6). undo the retaining screw for the break beam sensor PARTS LIST Fig 9.4 cover on the right hand side of the Geo using a 5/64" Fig 9.1 SPARES & ACCESSORIES (2mm) hex key (sEE FigUrE 9.1).
  • Page 29 “superchArGe” , so this should Also be checked. NOTE: the internAls of your inline reGulAtor mAy SERVICE CENTERS vAry AccordinG to the model of Geo thAt you hAve. with the threaded section towards to the base of PARTS LIST the regulator body, re-insert the adjuster screw into SPARES &...
  • Page 30 Fig 11.5 take the can and having cleaned off any old grease, PARTS LIST paint or debris, apply a small amount of eclipse Grease SPARES & ACCESSORIES once the threaded section is free from the threads in to the internal o-ring and the 2 external o-rings...
  • Page 31 SERVICE CENTERS take the bolt and having cleaned off any old grease, Assembly into the marker body (sEE FigUrE 11.17). paint or debris, apply a light film of eclipse Grease to PARTS LIST Fig 11.10 Fig 11.9 cover the front end of the bolt and also the internal SPARES &...
  • Page 32 (sEE FigUrE 12.1). with the Geo body and using the short arm of a 1/8” hex key, tighten the rear frame screw into place (sEE unplug the solenoid and the break beam sensor FigUrE 12.8).
  • Page 33 MAINTENANCE MAINTENANCE Fig 12.10 Fig 13.1 Attach the Geo rubber Grips to the frame using a 5/64” FAULT FINDING with the frame separated from the Geo body and the hex key to replace the 6 grip screws (sEE FigUrE 12.12).
  • Page 34 (sEE FigUrE 13.11) hold the solenoid Assembly onto the bottom of the Geo body, taking care to line it up correctly with the screw holes in the body and to avoid pinching the bbss NOTE: if Any of the components of the bAck- wires underneath it .
  • Page 35 Geo body (see page 62), use a 5/64” hex key to remove USING YOUR GEO bearing carrier, slide the trigger pin in place and using a the two screws that hold the bearing carrier in place 1/16”...
  • Page 36 MarKEr EasiEr TO wOrK ON. lubricate the narrow end of the oops pin with a drop SERVICE CENTERS of eclipse oil and push the pin, narrow end first, into the PARTS LIST oops body so that it sits in the oops insert and pokes having disconnected the macroline hose from the SPARES &...
  • Page 37 SERVICE CENTERS use a low quality or rechargeable battery. PARTS LIST the Geo leaks from the solenoid Assembly. check that the solenoid gasket is intact and replace the solenoid gasket if damaged. SPARES & ACCESSORIES seated in its designated pocket in the minifold.
  • Page 38 Geo has low velocity on the first shot. fsdo parameters are set too low to overcome Adjust fsd comp and fsd dly parameters. o-ring stiction.
  • Page 39 QUicK gUidE plaNET EclipsE llc grOUNd zErO paiNTBall acTiON paiNTBall gaMEs CONTENTS Are you unsure of where to send your Geo to be repaired or serviced? if your local eclipse dealer can’t assist you, Australia rhode island southern states ORIENTATION...
  • Page 40 QUicK gUidE parT NaME CONTENTS ORIENTATION QUICK SET-UP bolt plastic push button strip body USING YOUR GEO bolt front o-ring display window Anti double ball (Adb) finger MENU TREE bolt bumper o-ring navigation console clamping feed tube ADVANCED SET-UP clamping feed tube screw...
  • Page 41 O-riNg O-riNg lOcaTiON lOcaTiON QUicK gUidE BOlT CONTENTS ORIENTATION QUICK SET-UP USING YOUR GEO middle prop shaft o-ring MENU TREE bolt rear o-ring ADVANCED SET-UP can outer o-ring #013 NBr 70 MAINTENANCE rear prop shaft o-ring FAULT FINDING SERVICE CENTERS...
  • Page 42 QUICK SET-UP pcb screw (3), beArinG cArrier (2) maintain it with the eclipse tech on all maintenance and servicing the eclipse Geo. the eclipse ego9 is USING YOUR GEO ( m2.5 x5 cAp heAd socket) flex mat. procedures that require grease.
  • Page 43 UK & Europe: +44 (0)161 872 5572 call Usa & canada: 401 247 9061 licensed under one or more of the following patents: us 6311682, 6615814, 5881707, 5967133, 6035843, 6474326b1, 6637421b2 uk Gb 234270, Gb 2345953 © copyright 2008-2009 planet eclipse ltd. Geo and the Geo device are registered trademarks. gM08VOl2...

Table of Contents