Blodgett SB-10SC Specifications page 2

SB-SC CONVECTION STEAMER
SHORT FORM SPECIFICATIONS
Provide Blodgett model SB-6SC (6 pan), SB-10SC (10 pan) or SB-16SC (16 pan) convection steamer with steam coil boiler base. The SB-6SC and SB-10SC shall be mounted on a 24"
wide base (an optional 36" base is available). The SB-16SC shall be mounted on a 36" wide base. The SB-6SC is comprised of two 3 pan compartments. The SB-10SC is comprised of
two 5 pan compartments. The SB-16SC is comprised of two 8 pan compartments. Unit shall be constructed of 304 stainless steel with a one piece 316 welded stainless steel cooking cham-
ber with coved corners. The door shall have a removable inner liner of stainless steel with full perimeter gasket seal, an outer liner of one-piece all welded stainless steel, and a positive lock
and seal mechanism with spring release. Each compartment shall have removable stainless steel pan supports, A stainless steel drip trough integrally connected to collect and drain con-
densate with the doors open. The control housing shall be constructed of stainless steel with a full access removable panel. The controls shall include an on/off power switch with LED, a
ready indicator light, cooking indicator light, a 60 minute electric timer with audible alarm that signals the end of the cook cycle and CSD-1 secondary low water cut off. Steam flow to the
compartment shall be cut off when the door is opened during the cook cycle and shall be reactivated when the door is closed. The boiler base shall have full painted perimeter angle iron
frame, reinforced steamer and boiler mounts, stainless steel exterior, hinged doors and 6" (152 mm) stainless steel legs with adjustable bullet feet on the front and flanged feet on the rear
for mounting unit to the floor. Unit shall be ASME code stamped and National Board registered. Provide options and accessories as indicated.
WATER SUPPLY:
Water quality is a major factor affecting the performance of your steamer. If you are
unsure of water quality, consult a local water treatment specialist and have the water
analyzed. Your water supply must be within these general guidelines:
Total dissolved solids: Less than 60 PPM
Silica: Less than 13 PPM
pH Factor: 7.0 - 8.5
Water which fails to meet these standards should be treated by installation of a water
conditioner. Failure or malfunction of this steamer due to poor water quality is not
covered under warranty.
WATER & DRAIN CONNECTIONS:
Drain 2" (51mm) IPS piped to open floor drain. No solid connection.
24" length before open air opening (no bends or elbows)
Cold Water 3/8" (10mm) tubing at 25-50 PSI (170-345 kPa)
Condensate Return 1/2" (13 mm) IPS
NOTE: The company reserves the right to make substitutions of components without prior notice.
44 Lakeside Avenue, Burlington, VT 05401 • Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183
Printed in U.S.A.
Total alkalinity: Less than 20 PPM
Chlorine: Less than 1.5 PPM
BLODGETT
www.blodgett.com
NOTE: FOR COMMERCIAL USE ONLY
APPROVAL/STAMP
STEAM SUPPLY:
3/4" (19 mm) IPS
25 PSI (170 kPa) minimum
50 PSI (345 kPa) maximum
Steam take-off connection: 3/4" (19 mm) optional to oper-
ate adjacent equipment
POWER SUPPLY:
1/2" (13 mm) conduit connection to controls. 2 amps per
compartment
SHIPPING INFORMATION:
Approx. Weight: w/24" base
SB-6SC 550 lbs. (249 kg)
SB-10SC 675 lbs. (306 kg)
SB-16SC n/a
w/36" base
600 lbs. (272 kg)
725 lbs. (329 kg)
800 lbs. (363 kg)
P/N S00028 Rev H (1/07)