Table of Contents
Advertisement
Quick Links
Installation, Operation
and Maintenance Guide
AtmosSmart
OUR MISSION
To improve health and wellness by actively restoring indoor air
to its pure, natural state where no pollution or contaminants
exist, while reducing energy use and emissions in the process.
IMPORTANT
Save this Document
for Future Reference &
Warranty Information
AtmosAir.com
CAG-06-21-003
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AtmosAir AtmosSmart 500 Series
Summary of Contents for AtmosAir AtmosSmart 500 Series
- Page 1 To improve health and wellness by actively restoring indoor air Save this Document to its pure, natural state where no pollution or contaminants for Future Reference & AtmosAir.com exist, while reducing energy use and emissions in the process. Warranty Information CAG-06-21-003...
- Page 2 To the Holder of this Document The contents of this document are current as of the date of publication. AtmosAir® reserves the right to change the contents without prior notice. In no event will AtmosAir be liable for any special, incidental, or consequential damages or for commercial losses even if AtmosAir has been advised thereof as a result of issue of this document.
-
Page 3: Table Of Contents
Bi-Polar Ionization Description General Product Description Mode of Operation 02 INSTALLATION 03 STEP BY STEP INSTALLATION INSTRUCTIONS Installing AtmosAir 500 Series in a Duct 04 MONITORING DISPLAY INSTALLATION 05 ATMOSSMART CONNECTION POINTS 06 BMS CONNECTIVITY 07 A TMOSSMART/ATMOSCOMMS CONNECTIVITY & SEQUENCE 13 08 ... -
Page 4: Product Overview
The standard unit Voltage Range Control - 5 VDC, Cat5e / Cat6 simplifies monitoring and control of up to eight (8) AtmosAir™ Power Consumption 12 Watts Active Ionization Systems, using BACnet IP Communication. -
Page 5: Bi-Polar Ionization Description
The internationally certified and patented AtmosAir™ AtmosSmart™ is an integrated sensor array designed for System enables Bi-Polar Ionization at the AtmosAir Ionization installation in the RETURN duct of a typical HVAC air handling Tubes using controlled electronics. The surrounding oxygen unit (AHU) system. -
Page 6: Mode Of Operation
The HDMI port can output to a Tablet or a remote display (as specified). Longer HDMI runs than 35’ are achievable with an HDMI repeater. AtmosSmart™ is BMS compatible through BACnet IP and displays real-time Indoor Air Quality data to BMS. 1-888-MY-AIR11 CAG-06-21-003 AtmosAir.com... -
Page 7: Installation
The Sensor head should be mounted so that it is oriented on the centerline of the return duct with the impeller screen DOWNSTREAM of the ambient airflow, i.e., facing the filter, if present, or the AHU itself. 1-888-MY-AIR11 CAG-06-21-003 AtmosAir.com... - Page 8 Installation, Operation & Maintenance Guide AtmosSmart As many as 8 AtmosAir BPI units (500 Series and/or Matterhorn Series) can be controlled and monitored via the AtmosSmart™ system. More than one BPI unit being controlled is considered a custom application. The AtmosSmart™ systems are available in single BPI control or double (two-unit) control, as may be ordered.
- Page 9 Typically, every 30 seconds, an average of readings is taken. As the AtmosSmart sensor is read, that value goes into an AtmosAir proprietary algorithm. Every (2) minutes the ‘decision engine’ makes a go/no-go evaluation based on pre-programmed set points.
-
Page 10: Step By Step Installation Instructions
This transformer is provided with a standard plug suitable for the region/country in which the AtmosAir system is to be installed. This can be dedicated to the same, well-grounded, 15-amp service to which the AtmosAir BPI systems are connected. -
Page 11: Monitoring Display Installation
33’ (10 meters) is recommended. For longer cable routing, a HDMI repeater is required. Below are the 8 data points that the AtmosSmart system records, that can be displayed via an optional Monitor: 05 ATMOSSMART CONNECTION POINT BPI END BACNET / NETWORK END 1-888-MY-AIR11 CAG-06-21-003 AtmosAir.com... -
Page 12: Bms Connectivity
NOTE: The two ends with receptacles of the AtmosSmart Sensor Probe are generally arranged as ‘network’ and ‘display’ on one end, and output to AtmosAir BPI Systems and Micro-USB on the other. If the AtmosAir BPI control cable is plugged into the wrong RJ-45 cable receptacle nothing will happen. -
Page 13: Control Sequence
■ Every 30 seconds, an average of readings is taken. As the AtmosSmart™ Ozone (O3) sensor is read. That value goes into a proprietary algorithm. ■ Every 2 minutes the ‘decision engine’ makes a go/no-go evaluation based on AtmosAir set-points. If the value is below that limit the BPI unit will restart. -
Page 14: Product Warranty
Clean Air Group or the dealer where you purchased the unit. Disclaimer: The air purification technology provided by AtmosAir is intended to improve air quality. It is not intended to replace reasonable precautions to prevent the transmission of airborne contaminants. Customer, its employees, invitees and all persons having access to the serviced premises should comply with all applicable public health laws and guidelines issued by federal, state and local governments and health authorities such as the Centers for Disease Control and Prevention (CDC).
Need help?
Do you have a question about the AtmosSmart 500 Series and is the answer not in the manual?
Questions and answers