Advertisement
SHORT FORM SPECIFICATIONS
Provide Blodgett model CB42G-10-10K two 10 gallon direct steam kettles on a 140,000 BTU gas boiler base base.
The kettles shall have a double wall interior to form a steam jacket around the lower 2/3 of the kettle. The bottom of the kettle shall be of hemispherical design for superior heat circula-
tion. Steam control valve mounted in leg. The tubular stainless steel mounting legs shall have the steam supply and condensate return pipes completely concealed within the leg meme-
bers. The sealed stainless steel tilt mechanism bearings shall permit the kettle to tilt forward 90° for complete emptying. A removeable operating handle with heat proof knob shall be
mounted on the left or right. Unit shall have a single support leg with nylon insert. Construction shall be all welded satin finish 304 stainless steel with a 316 stainless steel liner.
The boiler shall be suitable for operation at any pressure from 5-11 PSI (34-76 kPa) and operate on 120 VAC. Boiler shall be mounted in cabinet base. Polished stainless steel cabinet
base shall be of modular design to match other Blodgett steam equipment. Unit shall have 6" (152mm) stainless steel legs and adjustable bullet feet, reinforced stainless steel counter top
and hinged doors with magnetic latches. All piping shall be confined within the cabinet. Unit shall be automatically filled with water and brought to pressure when power switch is turned
on. Cold water condenser shall automatically condense exhausted steam in water before releasing it to drain. Boiler controls shall include automatic water level, pressure gauge, water
gauge glass, pressure control with pressure safety control, safety relief valve, cathodic protector and CSD-1 secondary low water cut off, electronic ignition and automatic boiler blowdown.
Unit shall have a hot and cold water faucet with control valves, 5" (152 mm) deep sink with drain and two splash guards.
Kettles and boiler shall be ASME code stamped and National Board registered. Provide options and accessories as indicated.
WATER SUPPLY:
Water quality is a major factor affecting the performance of your steamer. If you are
unsure of water quality, consult a local water treatment specialist and have the water
analyzed. Your water supply must be within these general guidelines:
Total dissolved solids: Less than 60 PPM
Silica:
Less than 13 PPM
pH Factor:
7.0 - 8.5
Water which fails to meet these standards should be treated by installation of a water
conditioner. Failure or malfunction of this boiler due to poor water quality is not covered
under warranty.
WATER & DRAIN CONNECTIONS:
Drain
2" (51mm) IPS piped to open floor drain. No solid connection.
24" length before open air opening (no bends or elbows)
Cold Water
3/8" (10mm) tubing at 25-50 PSI (170-345 kPa)
Steam Take Off 3/4" IPS optional to operate adjacent equipment
NOTE: The company reserves the right to make substitutions of components without prior notice.
www.blodgett.com 44 Lakeside Avenue, Burlington, VT 05401 • Toll Free: (800) 331-5842 • Phone: (802) 860-3700 • Fax: (802) 864-0183
Printed in U.S.A.
CB42G-10-10K
Total alkalinity: Less than 20 PPM
Chlorine:
NOTE: FOR COMMERCIAL USE ONLY
GAS SUPPLY:
3/4" IPS supply line required
Minimum Inlet Pressure:
Natural
Propane
POWER SUPPLY:
Less than 1.5 PPM
Unless otherwise specified, field wire electrical con-
nection to be 120VAC, single phase, 60 Hz with
grounding wire.
PRODUCT CLEARANCE
Right and Left side
Rear
SHIPPING INFORMATION:
Approx. Weight:
CB42G-10-10K
BLODGETT
APPROVAL/STAMP
4.0" W.C. static to unit
11.0" W.C. static to unit
3" (76mm)
6" (152mm)
820 lbs. (372 kg)
P/N S00096 Rev A (7/06)
Advertisement
